The problem that the washing machine is noisy during the spin cycle is not as harmless as it seems. If the noise in the extraction mode is accompanied by extraneous sounds, you need to understand the causes of such work.
Repair Wizard identified a number of reasons why the washing machine during the spin cycle is very noisy. It all depends on the specifications of the model, the conditions and duration of use.
Bolts set for gentle transport, are not removed. This occurs when the user installs the car without the help of professionals. To secure transport of the machine on the rear wall mounted fixtures that hold the cushioning spring drum. It rotates without shock absorbers and knocks loudly.
Damaged bearings drum drives. The rotational mechanism is based on the guide bearings that can withstand enormous loads during spinning at high speed. Over time, they become useless. Define the problem in two ways:
Unplug the appliance, rotate the drum in opposite directions. If you hear crackling, then the matter in the bearing.
Foreign bodies stuck between the walls of the drum and the tub. If the washing machine is noisy and rattles more than usual, the reason may be foreign objects from the pockets of trousers or jacket.
Loose pulley drive system drum. If during the spin cycle increased noise and strange clicks - Loosen the drum pulley. If the time to identify the problem, this happens only after prolonged use stiralki.
Poor fixed counterweights tank. When the washing machine during the spin cycle hums and begins to rumble, there is reason to check balances. That they balance tank, which rests on the springs and do not let it sway. Counterweights attached to the machine by conventional screws or bolts. During the work of the screws are weakened and stiralka vibrates during the spin. Find weakened elements can be visually after removing the rear cover. After the inspection, tighten the screws become loose.
Rubber hatch cover seal is not fitted in size. If, during rotation of the drum unit emits a whistling sound unusual, the cause may be a circular hatch gum. After washing, can be found on the hatch trim rubber chips. According to specialists, in the machine-Machine budget type quality seal installation on the lower hatch.
Washing machine installed incorrectly. Because of this, the machine can also buzzing in the spin mode. The unit vibrates, moves on the floor, swinging and knocks. The reason for this setting is not on the level. The skewed state machine can not operate normally. It is necessary to eliminate the imbalance, otherwise it can lead to more serious problems.
Clogged filter: device noise when push-ups and you drain the water sound is amplified, the car starts to shake. The reason for this in the pump. The filter is clogged and the water goes to work.
It happens that the unit is noisy, but the drum does not rotate. This means that the engine is not running. If the drum does not interfere, the reason failure of the engine. In this case, take it to a service. Sometimes it is cheaper to buy a new stiralku than replace the item.
When the machine makes a very loud sound, it is not always failure. Some models in the instructions indicated an increased noise level in the extraction mode.
Elimination of damage with his own hands
Eliminate the causes stiralki noise during the spin cycle can be yourself. It is important to observe safety precautions before and repair disconnect the unit from the mains.
Do not remove the bolts set for transportation. Remove the transit bolts that hold the shock absorbers. They are located at the rear of the device closer to the center and unscrewed with a spanner. After that knock has to stop.
Damaged bearings. To correct the problem, you need to replace a part. In the absence of such experience entrust this work art.
Foreign objects inside the unit. To remove unwanted objects, remove the rubber gasket and loosen the heater heating element. Remove objects, return the heating element and a circular gasket in place. All this is done only with the device disconnected from the network.
Loose pulley. To solve the problem, remove the back wall of the machine and the tool tighten the fixing nut Pulley weakened. Pour mounting sealants.
Securing balances tank. Remove the rear wall of the unit, locate the weakened elements and tighten.
The problem in the rubber seal cap. Between the sealing rubber and the body put a piece of sandpaper and turn the machine on wash cycle without things. 30 minutes later trim the sandpaper roughness of the seal. Remove the remains of the cut chips, wipe the surface of the hatch and drum.
Improper installation of the machine. Line up the housing of the level typewriter strictly indicators mounting legs to twist.
Cleaning the filter. Remove the pump and clean it from dirt and foreign objects. If the pump is faulty, replace it.
If the machine still buzzes or rattles when spinning, call a service technician.
Prevention of faults
The washing machine worked effectively for a long time without interruption, take care of it and follow the simple rules of use:
- Before starting check whether unscrewed shipping bolts on the rear side of the device.
- The spirit level adjust installation.
- Do not overload the device lays the amount of laundry, the instructions provided.
- Do not use the machine several times a day: the drum does not have time to dry and seal wear gum.
- Do not use frequently wash cycle with hot water and high-speed spin.
- Keep the drainage filter is clean.
- Use a water softener to prevent limescale or install water filters.
- Before washing, remove all of the pockets. For clothes with metal decorations and lightning is best to use a special bag for washing.
Treat carefully to your washing machine and listen to outside noise. Proper use and maintenance will prolong its lifespan.
