Methods of laundering foam with it: the nuances of the material, methods and means for flushing it with skin

Every man for once in your life picked up a hammer or other tool. Such is the share of men, so to know some secrets that can help in the repair, it is recommended to everyone.

Not every man had to deal with mounting material, but if faced with it in the process, it knows what difficulties may arise when working with him.

For example, not so easy to remove the mounting foam away with. People who worked with her, you know how difficult it is to do. Of course, it is recommended before starting to wear gloves in order to subsequently avoid getting foam on your hands, but even the experienced master is not immune to this. What is already talking about the people who are starting to work with this material for the first time.

Removal of the liquid foam with hand

Some craftsmen are advised to work generously lubricate your hands bold cream or vaseline as foam adheres to them badly and then remove it will not be difficult.

At the same time ignores the fact that work with your hands, slick with petroleum jelly or cream to keep tools is simply impossible.

In order to clean hands from foamIf it is still in a liquid state, it is necessary also to make some effort, so you should start with this.

In that case, if the material gets on your skin, you should try get rid of it as soon as possible. Strongly not recommended as the process of removing foam spread on the hands - unknowingly can immediately avoid this error, which complicate the process of subsequently removing the foam.

at the hands of the pollution can be removed using clean cloth or towel. But it should not just spread foam on the skin should move progressively available to the mass center of the spot, then to wash off. All this must be done before the composition hardens.

suitable means 

Before starting the work it is recommended to prepare in advance the special cartridge containing solvent. One can try to find a solvent from the same manufacturer as the material.

spray Apply in the contaminated siteAnd then simply wash off using plenty of water. It should be noted that such aerosols cope with mounting foam, located more in the liquid state, they are unlikely to be effective against solid pollution.

It can be used in such difficult situations based solvent acetone. In it you need to soak a napkin, and then quickly and thoroughly scrub hands with liquid foam. After that you should wash your hands thoroughly with soap and water.

In the case at hand there is no solvent, suitable kerosene. He can easily handle the liquid with foam, so that if it is at hand, flushing of the material does not would be so difficult.

If the hand is not kerosene, then you can use is available in every home vegetable oil. His pre-need a little warm up and then moisten it in a napkin. You need to be patient, as the oil will need to keep in place pollution twenty or thirty minutes.

Advantages of this method is that it is completely harmless to the skin, as well as its efficacy: if enough to hold the oil in the contaminated site, the skin will not even remnants of the material.

Can be used table salt. Not need to perform any complex manipulations with it. It will be necessary just to rub salt place soiled, and then wash your hands with soap and water.

If the reader has long been thinking about how to remove the mounting foam away with, as a result of sitting long on case password might stumble on the recommendation to use as a means of removing this material is the drug "Dimexidum".

Perhaps there is some truth, but not recommended this drug for this purpose, as it can enter the body through the skin during the removal of the foam. Do not forget that each medication has its own side effects, so do not risk it. In any case, "Dimexidum" can then be used to remove the material residues from the floor or walls.

If the material is already cured

Everyone knows that if not immediately remove the mounting foam away with, then after a while it becomes hard. This can be a real problem, causing headaches, since the removal of construction foam from hands will be several times harder.

But anyone can face, and with this, so you should be able to clean the mounting foam away with, if it has already become a firm. This will be discussed later in the article.

After mounting material hardened on the hands, then wash with hand assembly foam will not workEven using solvents and other agents which have been mentioned above in the list.

It should be noted that this fact is indicated in the operating instructions of the material. So do not get to do without mechanical action.

So, to wash the foam core to the skin, suitable stiff brush or pumice. In any case, nothing special, and expensive does not have to acquire. Help funds held roughly at hand.

To scrub solidified mounting material from the skin need to take the following steps:

1. it is recommended to grease the hands of sunflower oil, or some cream to mitigate the effects on the skin in the process of removing the foam. This will avoid rubbing or more serious damage to the skin when removing material.
2. Next, you need to take a longer brush or pumice. The selected tool will have abundant lather.
3. Lathered with pumice or brush to gently, slowly, to clean off the cured foam from hands. Thus it is necessary to do everything carefully, so as to reduce the risk of skin injury.

You can finish off the best effect, but it is recommended that before hands to steam in the hot water for ten minutes. After all these manipulations will be carried out, it is possible to spread your hands greasy cream.

helpful hints

In the event that all of the above methods did not work, and the remaining material is not got away with, something very upset and do not panic. A few days later traces of foam peeled from the own hands, as skin cells are constantly being updated.

In no case can not be used as solvents, foam materials that contain in its composition acids or alkalis. We are talking about substances such as Domestos, acetic acid and others.

The fact that they are still not able to cope with the remnants of the foam and use from them will not be any, but at the same time, their impact will be long burn. That's why use should not be.

Removal of foam from hands will not pass unnoticed by the skin, as throughout this process is the impact on it. That is why it should not be neglected.

After the manipulation carried out immediately should take care of the skin. This will require grease hands with a nutritious creamWhich has antiseptic and regenerating properties. For such purposes suitable creams containing ginseng juice or aloe.

Rules for working with foam mounting

To avoid possible contamination of foam on hands and other body parts, the walls and floor, it is recommended to take care of it.

• Before you begin, it is recommended to wear safety glasses and gloves.
• Better to use the clothes you do not mind then will throw out if it gets this stuff. It must be remembered that frozen tissue on the foam has not come out to wash.
• It is recommended to work to put on the head of any headgear. Make required due to the fact that the foam got on the hair and then will act immediately with hair already.

Sex is better to cover the unnecessary disposable material - polyethylene film or cardboard. It is advisable to buy some cleaning agents together with assembly foam. They need to scrub random spots. It is better to carry out all work with the editing work with an assistant, who can in which case the hedge, and quickly remove the random spots.