Error e20 in the washing machine "Electrolux"

The most common error that occurs during the operation of Electrolux washing machines is e20.Experts associate it with the problems that have arisen in the drainage system, along which already drained water flows. Before you do repair the device, you need to understand why there is an error e20 in the washing machine "Electrolux".In this article, we will consider in detail all the steps involved in verifying the details that could have caused such a malfunction.

to the contents ↑

For what reasons does the washing machine "Electrolux" give an error of e20?

To begin with, remember when the last time you cleaned your machine, and if it was more than two years ago, then most likely the cause of the breakdown is hidden in a plugging blockage.

Important! People who always follow the rules of using household appliances, using powder suitable specifically for automatic machines, regularly using air conditioners and water softeners, never face such problems. Otherwise - your favorite washing machine "Electrolux" will make you nervous.

Error e20 occurs in the following cases:

1. The nozzle or drain hose is clogged.
2. The drain pump is broken or clogged.
3. There is a problem with the level sensor or the wires are blown.
4. The electronic module has failed.

to the contents ↑

How to fix e20 error yourself?

1. First disconnect the washing machine.
2. Then drain the water from the drum directly through the drain hose - for this it will have to be disconnected from the sewer.

Important! In this case, watch carefully, if the water flows easily, then most likely, blockage formed in the sewer. It will be necessary to clean the pump or siphon.

1. When all the water has merged, you will need to remove all the linen and continue to look for and fix the problem.

If there is no clogging in the sewerage check, then check the filter and the drain pump:

1. First unscrew the filter and pull it out.
2. Then rinse thoroughly under running water.

But with a pomp it will be more difficult, as it is hidden in the cars of this brand behind the back wall. We perform the following actions so that the error e20 in the washing machine "Electrolux" does not bother you anymore:

1. We unscrew the bolts from the rear wall to remove it.
2. Removes an already unscrewed surface.
3. Disconnect the wires connecting the pressure switch to the pump.
4. Remove the bolt located on the bottom of the device holding the pump.
5. Carefully unclip the clamps on the spigot and drain hose.
6. We take out the pump.
7. After disconnecting the pump, separate the nozzle from the tank.
8. Look at it from all sides, rinse under running water. Use a special cable to clean the drain hose.

Finally, proceed to the pump.

Features of cleaning the pump

In order to clean it thoroughly, unscrew the cover from above and carefully check the impeller. She often reels in her hair, hair and thread. All the garbage we choose and wipe it dry.

The multimeter will help when checking the pump - you need to attach its probes to the pump and see what the resistance of the winding is. If it is less than 200 ohms, you will have to buy and install a new pump.

If the error occurred because of a breakdown of the pump, then after reinstalling the device should normally earn.

Important! If you are first disassembling your washing machine, be sure to take photos of each stage of the disassembly in order to collect everything correctly.

to the contents ↑

Troubleshooting in the pressure switch, wiring and electronic module

It is necessary to check further the serviceability of the wiring and the pressure switch that connect the water level sensor to the electronic board and pump. Have you all carefully examined and found no breakdowns, and the error e20 remains? Then you need to start checking the electronic module.

Important! This process will take a lot of time and effort, because the work is serious and painstaking, even not many experts agree to it. Most boards are simply changed, not repaired, because they are inexpensive. But you should not be frightened, because such errors occur very rarely.

Important - take your time when you find that the display shows error e20."Electrolux" is a brand produced by which the technician often issues such errors, but they are usually easily correctable.

Important! Inspection is best done from the simplest stage to the most complex one. Do not immediately begin to disassemble the unit, perhaps the cause of the failure is not as serious as it seems to you.

to the contents ↑

The most common error codes for modern washing machines

Next we will look at the example of the most popular in our time automatic devices for washing, what other errors can occur and how to deal with such situations.

Errors in washing machines "Ariston" and "Indesit"

All models of units of these brands, issued after 2000, are equipped with a device for indicating errors. Thanks to the electronic module, the device is able to independently determine and report what the problem was. Depends on the year of production of the machine, they all in their own way report errors.

Important! The very first electronic models in such cases begin to give a signal, reflected in the form of flashes on the power indicator. Blinking occurs at a certain interval, and that's exactly their number indicates the number of the error that occurred. In more modern models, a fault code can be determined by a combination of indicators blinking on the panel.

The most popular errors in Ariston and Indesit models:

1. F01 - means that a short circuit has occurred in the motor control circuit.
2. F02 - the controller has stopped receiving a signal about the operation of the motor.
3. F03 - the temperature sensor or the TEN relay has broken.
4. F04 - problems with the pressure switch.
5. F05 - the pump has stopped functioning or there is no signal that the drum is empty.
6. F06 - there was a problem with the buttons.
7. F07 - the element for heating the water has not been lowered into it.
8. F08 - the water sensor reports a overflow or empty tank.
9. F09 - a failure in the system.
10. F10 - water for washing is not enough.
11. F11 - the console does not receive a signal about the pump, most likely it is broken.

The most popular service errors in Siemens and Bosch devices

If you decide to purchase a washing machine for one of these brands, you can find out which faults are more likely to occur in them and how to fix them yourself. These codes are:

1. F01 - the drum door is not closed securely. To fix the problem, you need to check if the door is closed and put the laundry in the hatch again, so that nothing is trapped by the door.
2. F02 - water does not enter the tank. It is necessary to check if the tap, through which water enters, does not clamp or bend the hose. Also, the error may appear due to insufficient pressure of water or blockage in the filter, which you can eliminate yourself - just remove the hose and clean it.
3. F03 - the drain pump is broken, namely, garbage or other objects accidentally got into the hose. It is easy to clean it according to the manufacturer's instructions.
4. F04 - the water poured onto the floor or flowed into the pan. To correct this defect, it is necessary to call the master.

The most common errors in the Electrolux and Zanussi devices

The e20 error in the Electrolux washing machine, unfortunately, is not the only problem that can arise with the models of this manufacturer's equipment, as well as its analogue - Zanussi. Here are the most popular errors:

1. E10 - water ceased to be fed into the device. To solve the problem, it is necessary to open the tap, where the water comes from the water pipe, further check that it starts to flow. Also it is necessary to check the condition of the hose, through which water flows - perhaps it tore and bent in some place. Or maybe inside it formed a blockage or debris accumulated in the filter located at the entrance.
2. EF0 - the washing machine "Electrolux" suddenly stopped draining the water. Error e20 is characterized by the same cause of failure, while in order to restart the unit, you need to check the operation of the drain hose and pump.
3. E40 - the door of the loading hatch is not closed. Try to close it again and arrange things neatly so that nothing sticks between the door and the tank.
4. E90 - out of order one or several electronic parts went out. Try turning off the device and selecting the desired program again and turning it on again. If the error occurs again, you will have to resort to the help of a specialist.

Now you understand more why error e20 has appeared in the washing machine "Electrolux", what other codes are signaled to you on the equipment of this and other brands, and what to do with these troubles, to restore the working capacity of the equipment and not to bother with manual washing.