How to remove a window sill from a plastic window?

The window is a perfect light source, as well as reliable protection against heat or cold, rain or snow, wind and other atmospheric phenomena. And an integral part of every window is the window sill. However, sometimes, due to an absurd accident, it can be damaged or simply not fit the size. In this case, you need to replace it with a new one - wider or, vice versa - already, or simply another in external execution. This is where the question arises, how to remove the windowsill from the plastic window, and whether it is possible at home. The answer is simple - yes, yes, but you need to follow the instructions clearly.

to the contents ↑

Preparing for dismantling

Before proceeding directly to the dismantling, it is necessary to prepare tools that will be useful to us, and naturally - the room itself. And also be sure to determine the material of this part of the structure, as this will depend on the method of dismantling used.

Important! Window sills can be made of plastic - the most common), as well as wood or concrete.

Tools:

• Scrap.
• Conventional and demolition hammer.
• Hacksaw.
• Chisel.
• Chisel.
• Bulgarian( not always necessary).

to the contents ↑

Dismantling the

Be extremely careful and careful, as repair is like a "jewelery" work that requires attention. Otherwise - you can destroy the walls or, worse, stay without fingers. So, let's start solving the problem, namely, how to remove the plastic window sill.

Wooden

If you need to replace a window sill made of wood, use a crowbar and a hacksaw. Check how the part is attached. If to the wall, then to remove the window sill from the plastic window:

1. Try to loosen the fasteners, slightly punching it with a hammer from below.
2. Then you need to get a window sill.
3. If this attempt is not successful, use a chisel and a hammer.

Important! If you still can not solve the problem, you can make the cuts and then get an unusable part in parts.

Concrete

If you need to replace the concrete window sill, be prepared for the fact that there will be a lot of dust. To remove it you will need a Bulgarian and a hammer. However, if you do not have a Bulgarian, you can replace it with crowbar and chisel. You need to delete exactly the same way as the structural element made of wood.

Plastic

If you have a question about how to remove a plastic window sill, there are two ways. Both are quite effective, but the first method is more destructive than the second.

1 way:

1. You need to peel the plaster and remove the slopes.
2. Then cut the construction foam with a sharp knife or other object with a sharp blade.
3. After these actions, it will be enough to pull the sill a little and it will be removed.

2 way:

The second method - on the contrary, is based on the preservation of plaster and all slopes, but will require more time and effort:

1. You need to cut the mounting foam under the window sill.
2. Then remove the liquid plastic near the slopes.
3. After this, as in the first version, you can easily get a window sill.

to the contents ↑

Useful advices

When deciding how to remove a window sill from a plastic window, it will be appropriate to remember that when installing it at home, it is necessary to take into account some important factors:

1. The new product should be 10-20 centimeters longer than the width of the window unit. When installing a part of the plastic model will be in the wall, and the protrusion of the board should be not less than 50-70 centimeters.
2. Mount a new surface during installation with a mounting glue or special mortar.
3. After a while, when everything dries, put special caps on the edges of the windowsill.
4. If you have a non-plastic window sill, such as wood or cement, you can try to remedy the situation without removing the part from the window unit. To do this, you will need a liquid deep penetration primer, diluted with putty powder. After applying the solution, immediately level it with a spatula. This is a very reliable and effective tool, so in most cases the problem of removing defects can be solved without resorting to the replacement of the window board.

So, if you carefully studied this article on how to remove a window sill from a plastic window, you have unequivocally gleaned information about how to solve this problem at home, and also learned several options in which it is not necessary to spend money for replacement, because you can bring the old to life. We hope that you will keep in mind the above methods and recommendations, and henceforth, when you face this task, you will not have a question how to remove the plastic window sill, because you already have enough knowledge. It remains only to learn how to properly implement the information received.