Before making accessories for your smartphone, you need to think about how to use raw materials, because the body of the finished tripod should be sturdy.
CONTENT
- 1 How to make a stand for your phone with your hands
- 2 How to make a stand for your phone from scrap materials
How to make a stand for your phone with your hands
The first step is to understand what the problem is made to perform a tripod. If you have to use it constantly, it is necessary to consider which of the materials choose to have it served durable. If you plan to use not so often, but I want to save, you can take the raw materials, which always have a home. Let's get to the point.
If you carry a wooden stand for a camera or smartphone, it is better to cover its stained - so it will last a long time.
From the plinth for plastic windows
When the house changed to more modern glazing, necessarily remain some waste. In this case they will use. To begin, prepare all the equipment, so you do not get distracted from your work.
When working with different tools necessary to observe safety precautions.
Materials and tools
To work required:
- plinth of plastic windows;
- hacksaw;
- knife;
- drill;
- metal tube.
Please note that plastic grown old will not work, as it may crack during use.
Do not attempt to increase the capacity of the recess for the smartphone mechanically, it can cause damage to the plastic holder.
Step-by-step instruction
- Take the rest of the plastic and cut off from his part in half more than your smartphone.
- Prepare fastener in which two holes drilled in them and insert screw and ball-detent.
- Measure the diameter of each locking member. Then attach the prepared plastic and note that will contain these details.
- Making holes in the piece of skirting board with a corresponding diameter and feint ball.
- Now fasten the adapter and fasten it to the foundation of the future tripod.
- The edges of the plastic handle with electrical tape, duct tape or silicone adhesive, so they do not scratch the phone.
- Next, fasten the length of the telescopic tube (can be normal), put the smart phone into the slot, and then start shooting.
GOOD TO KNOW! (Click to see)
If in doubt about the reliability of the holding device, the phone can be locked by means of elastic bands. Use a thin and flexible, for a slingshot.
Mini Tripod with your own hands can be used as a portable tool for shooting.
Adjustable tripod made of cardboard
To some it may seem that any board is not able to reliably hold the phone in time to shoot. However, if you do everything according to the instructions, you can get a solid tripod for continuous shooting.
Bare aluminum wire is better not to be used to construct stands. It is better to choose one that has a protective sheath.
Materials and tools
You will need a tripod for the manufacture of cardboard:
- Any cardboard box;
- scissors;
- line;
- ball pen;
- pistol glue.
Some embodiments of the racks can be made from old monopod.
Step-by-step instruction
Immediately prepare your desktop to work in the process save time searching for equipment. Next, proceed to making a tripod.
- Cut cardboard box into several parts (three parts will need a size of 10 × 6 cm).
For cardboard boxes tripods are more suitable from the large home appliances.
- Now take a part and draw a line thereon at a distance of 20 mm from each other. We make a four-lane and cut off the excess
Cardboard stand can be made of colored cardboard or make it your own design.
- Now Burst line drawn by each line and bend the figure outside. Then, the resulting edge between a glue gun.
Glue gun is best used for flexible materials only.
- Now do the same with the second cardboard, only draws a line at a distance of 16 mm.
Women often make the tripods of hair accessories, flexible curlers.
- Again forced and bend them, form a glue gun shape.
Paper racks can be used double-sided tape, paper clips stapler.
- Next, insert a smaller size in a large part.
Tripods, which are made high, it is advisable to install on Trinoga.
- Measure out the required distance at which the phone should be set during shooting and pierce two holes in the cardboard. We put them in the lock (can be made out of paper).
For holders it is recommended to install the foam, to leave no trace of the stand in the phone.
- Now, on the edge of the top piece of our tripod we make an incision that will keep your smartphone. Their depth should be at least 1 cm.
Stand for smartphones can be decorated in various ways, to do design models.
- Further, forming a stand for a cardboard devices. To do this, the remaining part of the box to the prepared glue gun tripod.
Some tripods can be adjusted depending on the width of the smartphone installed.
As a result of the above actions, you get a solid self-made tripod stand, which can be used on the table when the selfie or video capture.
Tripod Stand for smartphone plywood
Plywood - is one of the breeds of wood materials. It is used for different purposes. Today we use this tablet for the manufacture of Stand by your phone. Required for this purpose will need a diagram or drawing.
Flexible tripod for your phone attached to any object, similar to a wire products.
Materials and tools
To create a wooden stand on the phone, you need to have on hand:
- a pencil;
- plywood;
- jigsaw.
Step-by-step instruction
- Prepare plywood cut out from it two details size 10.5 × 12 5 cm × 5 cm.
- Otshlifuem two fragments, views to the edges no burrs.
- Making sawing at a distance of 2-2.5 cm from the lateral edge of the workpiece. The width of the sawn pieces on each part shall be not more than 5 mm.
- Remember that drank carry about the middle. Next, connect the two parts together "slot-in-groove".
- In detail, which has a shorter length do recess chisel, then grind it with sandpaper.
- Now we cleanse our preparation, and should be covered with varnish or made out in an interesting design.
- After a recess set our smartphone and enjoy the result.
Plywood boards and can be made thin weight products of interest as supports for free. When creating an accessory for a child, it can be based on diagrams of different small animals or colorful geometric shapes.
Performing accessory with your hands, you can use a burning technology for the design drawing.
How to make an interesting wooden tripod
Everyone who uses the camera on your smartphone, understands that image quality is directly dependent on the immobility of the device. The convenient and reliable set the phone on a tripod, the better the resulting image.
Structure for holding the smartphone can perform additional functions, e.g., to serve a miniature hanger.
Materials and tools
- wooden blocks;
- Holder smartphone;
- fastener from a table lamp;
- glue gun;
- thin PVC pipe.
Some tripods provide the ability to charge your smartphone.
Step-by-step instruction
- First prepare all the bars to be processed. For this proshlifuem them on all sides, to remove irregularities.
- Next we take a big stick and stick to it little at the edges.
- Wide plane will be the basis of our tripod.
- Now glue the PVC pipe to the prepared bar.
- Two symmetrical holes are drilled with a diameter corresponding fasteners.
- Inserting the fixing member, forming a small rectangular bar with the same hole, which is subsequently attached to the reacting mechanism.
- On top of the glue stick produced one more, slightly larger. It will serve as a platform.
- Now, to the resulting structure fasten the plastic holder for the phone in a horizontal position.
After the above actions can be used as a self-made tripod with purchased. Such a device can be used at home to shoot a full-length video.
Many stands are suitable not only for smartphones, but also for some of button cell
How to make a stand for your phone from scrap materials
Among the variety of tools and materials that can be used to create a makeshift tripods, there are options that are always in the house. At this stage of Pohorje is on such devices.
Devices of the clips can be done not only for the phone, but also for flash drives and portable players.
Gadget for clamping of securities
When the house has a holder for files and documents in large numbers, they can be applied with great benefit to the phone. It is because these devices are going to create a simple tripod.
- To prepare a portable stand one large binder, and the other smaller.
- Open big fixture, place the handle of a small construction and slams into him.
- We lift up the bottom bracket, then simply install it on your smartphone stand.
- Ideally, the best prosilikonit verge of a mini tripod to avoid possible scratches on the body of the phone.
At the same time multi-functional supports can be stored up to three smartphones.
GOOD TO KNOW! (Click to see)
Such a device is easy to carry in a bag, organizer, or even in your pocket. Especially useful is a gadget for those who work in the office and always keeps the cell at hand.
Option of linen clothespins
For this purpose, it is advisable to use as plastic and wooden clothes pegs. However, it is worth noting that the latter will look better, especially if they decorate any of the methods. Proceed to the implementation of the stand.
- For products require a ballpoint pen and 5 pegs.
- Fasten all the pegs from the middle to the edge of the cap.
- Two extreme unfold in a reverse direction.
- The following two (located on opposite sides) rises.
- We can assume that the tripod is ready. Install it and use the phone as a normal stand, or a means for shooting.
Glam stands for girls perform in bright colors.
In this version, the accessory can be adjusted by the location of the slope of the smartphone.
Tripod from a piece of copper wire
Next homemade version supports more than suitable for cameras. Make this accessory is not difficult, the main thing - to properly prepare all the tools.
- Collect the desired material: silicone tube, copper wire, brass adapters, two bolt clippers, the burner, water and dishwashing detergent, epoxy.
- Immolation copper wire, observing safety rules and quenched it with water.
- Cleans up a tow wire, then carefully put it in the silicone tube.
- The next step is put on the brass sleeve on the tube, it will serve as a connecting element for the bolt and wire.
- Followed by a bolt cut off the head grinder or metal saw, leaving a tail of 2-3 cm.
- Further, the adapter is screwed into the prepared detail fix her glue gun, but rather with epoxy. Outside the adapter must remain part of 0.5 mm. This is required for the further secure the camera.
- Anchoring the opposite direction similarly, but do not leave a bolt outside.
In use, the device can be screwed onto the branches of trees and any other support if there is no one, and take the picture - this business essentials.
In the manufacture of accessories for electronic materials is better to take with a reserve.
Dear users. Ask your questions in the comments, tell us if you liked the idea to create a self-made tripod. If something is not clear, we discuss as a priority.
about the author
Evgenii Tarasevich
Any technique, like a car, needs careful study and comparison before buying. Always I try to give your readers a full picture of a choice.
