Drain pump for washing machine

Today, manufacturers provide us with a huge selection of models of washing machines with various dimensions, functions and features of the system. And if there is a question of replacing the drain pump in the device, then it is necessary to understand just the design of the device, then the work will not be difficult even for a beginner. Today, let's talk about an independent replacement of such a detail as a drain pump for a washing machine.

to the contents ↑

We select the pump

The drain pump is a very important part in the washing machine. It is responsible for pumping water out of the device after the wash cycle. Today, it is not difficult to purchase a drain pump, and the cost is quite affordable. First, let's try to understand why this part can fail.

Lump

In this case, the system can not cope with the load for the following reasons:

• Hitting small objects in the hatch. Then from the device will be heard grinding, crackling and other extraneous sounds.
• Also, if a blockage occurred, it is possible that during the drain stage the device will simply hang and refuse to continue the program. In this case, the filter is removed and cleaned.
• If the filter is clean, then it becomes necessary to check the impeller, it may have jammed it due to a blockage. It is simply scrolled, and if everything is in order - check the drain hose pipe.

breaks If a blockage is not detected, the next step is to check the voltage at the pump terminals. To do this, take a multimeter and ring the wires.

Important! It happens that the drain pump of the washing machine can not be repaired, it must be replaced.

Selecting the pump

Even if you have found the cause of the failure, cleaned the filter or replaced the wires, but the drain pump of the washing machine has been working for more than five years - it is recommended to replace it with a new one. The main tips for selecting the details are discussed below.

Tips:

1. Do not buy cheap parts of unknown brands. It is better to purchase the original part from the manufacturer of your washing machine.
2. Before buying, be sure to check the instructions for your device. There should be a detailed description of the necessary parameters for the pump.
3. Some experts advise to purchase small pumps with a magnetic rotor, but like any other parts, they also have drawbacks. Such a pump can not synchronize in time, because of what its power will fall.

Be sure to carefully weigh all the pros and cons, do not pursue cheapness, because, as the saying goes, a miser pays twice.

to the contents ↑

Removing and replacing

Depending on which model you have, the drain pump on the washing machine can be installed both with the removal of the device walls and without dismantling. First, check whether it is possible to lift the pump through the bottom of the device. This is the easiest option of repair.

Dismounting the bottom of the

In most popular brands of washing machines, everything is quite easy: repairs take place at the bottom of the unit, since bottom protection may be missing, or it can be removable.

Important! In this way, you can replace the drain pump for the washing machine LG, Samsung, Beko, Candy, Indesit, etc.

Consider the basic steps:

1. Disconnect the appliance from electricity and water.
2. To ensure the safety of the housing, place a soft cloth under the appliance before starting work.
3. Place the device on its side so that the pinned pump is at the top of the device.
4. Remove the lower bar by removing its latches.
5. If the device has plastic protection for the pump, disassemble it.
6. Next to the drain valve are the screws on which the pump system is attached. Unscrew them and gently pull the pump out as far as possible.
7. Next, disconnect all wires from the pump.
8. After - it will be necessary to drain the water. Therefore, first prepare a bucket or other container, and gently unfasten the clamps over the container.

Important! When replacing a pump with a snail, also remove it. If its kind satisfies you - the snail can be left, but cleaned.

Before replacing the drain pump in a Samsung washing machine or other brand device, be sure to clean the cochlea, it should not contain contamination.

The installation process proceeds in the reverse order of dismantling. The pump is installed, in the seat to the cochlea, connect the nipples and wires.

Removing the front of the

For Bosch, AEG, Siemens and some others, the principle of replacing the pump will be somewhat more difficult. The thing is that the bottom of these devices is closed, and it's easiest to get to the pump through their front wall.

Steps:

1. It is not difficult to remove the front part of the case. To do this, unscrew the self-tapping screws that are located on the back of the device. After that, the lid can easily be removed by pushing from the side of the hatch.
2. Next, remove the upper front cover with the control panel. To do this, remove the powder tray, unscrew the cover bolts and carefully disconnect it from the body of the device.

Important! Remember that the panel is connected to the device with wires. They do not need to be unfastened. Simply lift the panel and place it so that it does not interfere with you when replacing the pump.

1. Below there is a protective plastic panel, behind which is a drain valve. The panel is also removed, and the valve is unscrewed above the container into which the remaining water is drained.
2. Next remove the cuff of the hatch from the front wall.
3. After - the bolts that hold the pump and the fixings securing the wall are loosened.
4. The wall is dismantled neatly: in such a way that you do not tear off the connections to the tank lock.

Important! The pump replacement is no different from the version where the dismantling is done through the bottom of the unit. After the repair is complete, assemble all parts, connect the device and make its test run.

Dismantling the rear wall

There are also devices with a vertical load or a fixed bottom and a front wall. Changing the pump in them is possible when removing the rear of the device.

The very replacement of the washing machine drain pump is no different from the previous versions. But here's how to get close to him, we will consider further.

Steps:

1. Drain the remaining water in the device.
2. Remove the upper part by unscrewing the two bolts.
3. We unscrew all fastenings of a back wall of the device: from above, from sides and behind.
4. Disconnect the water intake valve from the wall.
5. Remove the wall.
6. Disconnect all pins from the pump.
7. We change the pump.
8. Next, we collect the device in its initial state and conduct a test run.

Important! In this way, the pump is replaced in a vertical washing machine, as well as Zanussi models and some other brands.

Separate attention should be paid to Hansa washing machines. In them, the replacement is the same as the pump on the washing machine LG, but with the difference that the dismantling of the front of the device is not needed. The manufacturer has provided for work a small wall from the socle side, taking off which you will get access to the pump.

If the pump breaks down in the washing machine, it means - the device has stopped draining the water, and most likely an error code will light up on the panel. You can always have time to contact the repair specialists, or you can try to solve the problem yourself, just follow the instructions and recommendations.

to the contents ↑

Recommendations:

1. Any work on the device should be carried out with the power and water disconnected.
2. Take pictures of the entire work process - it's easier for you to assemble the device
3. Be sure to read the instruction manual for your model. In it, the manufacturer will write most fully about all the nuances.
4. In order for the machine to last for a long time without breakdowns, use only high-quality detergents intended for automatic machines.
5. If you wash items with small parts( buttons, sequins, etc.), use a protective mesh bag for washing.
6. For hard water, use special softeners and filters.
7. After completion of work and assembly, connect the device and check its operation by running the spin and drain mode.

In compliance with the rules of operation and timely preventative measures, the machine will easily and without breakdowns last for more than 10 years. And how to solve the situation, if at the end of such a period the drain pump of the washing machine is out of order, you now know.