๐Ÿ”จ Practical decoration Garden: Gardener throne of tires

click fraud protection

Tires - material for a huge number of artefacts from the furniture to the practical garden figures. To the Editor HouseChief came very interesting material from Olga Rubakin from Nizhny Novgorod. She and her husband have done a lot practical things of this worthless material. One such exhibit she will tell in detail.

Greetings to all my colleagues in the horticultural and passion! My husband and I bought a summer residence eight years ago. All the while enjoying the outdoor life. A garden, planted neat gryadochkiBefore house - parterre. And I want to enjoy the beauty of the whole day, with enjoy comfortably. wooden benches - not the most comfortable seats, plastic seats we like that do not survive. As one day I came across a short video in which the master of Latin America did to sell the chair of the tire. We reviewed the video with her husband about forty times, no less, and then decided to try and do.

Read article

  • 1 Where to get the tires
  • 2 The base of the chair
  • 3 How to make a chair seat
  • 4 we do back

Where to get the tires

In our garage They were two old wheels, but it was not enough. The husband went to the fitting center and there he was almost happy to have handed over a package. Rubber was "killed", but very suitable for our purpose. So get tires for gardening is not difficult.

The base of the chair

So, we need 5 chairs tire with an inner diameter of 32 cm.

If you have on hand a larger diameter tires - it does not matter, only that they were all the same
If you have on hand a larger diameter tires - it does not matter, only that they were all the same
You should begin with cutting rings for internal risk
You should begin with cutting rings for internal risk
The inner part of a well-cut with a knife, but to facilitate the task better place to pour liquid soap cut
The inner part of a well-cut with a knife, but to facilitate the task better place to pour liquid soap cut
Here is the ring you want to cut on both sides of the tire
Here is the ring you want to cut on both sides of the tire
The second band - width of about 8 cm. It can be cut - you need a band, not a ring
The second band - width of about 8 cm. It can be cut - you need a band, not a ring
Such a result of working with one side tire
Such a result of working with one side tire
And since the result looks full wheel with
And since the result looks full wheel with
On a narrow ring need to drill to drill two holes opposite each other
On a narrow ring need to drill to drill two holes opposite each other
After cutting two tires, you should have 4 such rings with holes
After cutting two tires, you should have 4 such rings with holes
Bolting ring 4 cm
Bolting ring 4 cm
Firmly tighten bolts for secure connections
Firmly tighten bolts for secure connections
The rings are connected in series, one after the other
The rings are connected in series, one after the other
The last ring is bonded to the first
The last ring is bonded to the first
Here is ready to seat and base. As you can see, the work is just beginning
Here is ready to seat and base. As you can see, the work is just beginning
Another two such rings should be cut in half to get 4 half rings
Another two such rings should be cut in half to get 4 half rings
They must be fixed to the support rings in this position
They must be fixed to the support rings in this position
Fixing is done all the same bolts
Fixing is done all the same bolts
I myself made a plush armchair of tires and has not spoiled manicure
Please note that the half-ring is mounted on the inside.
Result fastening half-rings on the base
Result fastening half-rings on the base
Now our task is to make sure that the legs are not slithered under load
Now our task is to make sure that the legs are not slithered under load
You need to cut 4 of such parts as wide as two feet
You need to cut 4 of such parts as wide as two feet
Small parts bolted to the legs and fix them firmly in place
Small parts bolted to the legs and fix them firmly in place

How to make a chair seat

When the foundation is ready, you need to make the very seat. For its production, in addition to tires, require small screws with rounded caps 2 cm long.

The basis here is the seat will ring. You can just try it on the ground to make sure that it works
The basis here is the seat will ring. You can just try it on the ground to make sure that it works
Now is attached to the edges of the base rubber strip with self-tapping screws
Now is attached to the edges of the base rubber strip with self-tapping screws
Creating a so-called twist band. Try to make it not too rare, so it's good to keep the weight of sitting
Creating a so-called twist band. Try to make it not too rare, so it's good to keep the weight of sitting
When the braid is ready, fasten seat bolted to the ground in four places
When the braid is ready, fasten seat bolted to the ground in four places

we do back

Comfortable back support - an important part of the seat structure. For the back, too, use rubber tires.

To back you need a wide cut the ring. Near the cut on both sides need to drill holes
To back you need a wide cut the ring. Near the cut on both sides need to drill holes
The third hole exactly at the top of the cut ring
The third hole exactly at the top of the cut ring
Will be mounted back to back-up rings and half-rings. To do this, prepare the holes and bolts
Will be mounted back to back-up rings and half-rings. To do this, prepare the holes and bolts
I myself made a plush armchair of tires and has not spoiled manicure
On the back side of the seat is necessary to prepare an opening for back support
On the back side of the seat is necessary to prepare an opening for back support
We need one more ring to support a width of 6 cm
We need one more ring to support a width of 6 cm
This ring is bolted in two places: the top and bottom of the back of a semiring
This ring is bolted in two places: the top and bottom of the back of a semiring
For the final fixing and giving back the necessary rigidity, it is necessary to make two more fixing
For the final fixing and giving back the necessary rigidity, it is necessary to make two more fixing
Admire the result: nothing throne gardener
Admire the result: nothing throne gardener
If you cover these chairs painted with a metallic sheen and polish - from a distance they look forged
If you cover these chairs painted with a metallic sheen and polish - from a distance they look forged

Such seats safely bear the weight of an adult. They are very comfortable, not afraid of rain and snow. We made a few pieces of such, and so broke that he had received a kit with table.

I can only say that now the tires - our favorite material. After manufacturing of seats we are left with the widest part of the tread, from it we did tile for tracks. If interested - I tell you about it next time. In addition, we have in the country have a trampoline for children and tires swingNot to mention the garden figures. Therefore, if you have something like that in the garage - do not rush to throw out, just come in handy. In conclusion I would add that one chair we took four tires. All the luck in the works and gardening!

Rubakin thank Olga for the detailed story and photos! Indeed, the tires can be used for many purposes: from the creation of septic tanks the area to arrangement of decorative ponds. In addition, we offer here is a small video on making simple and convenient pouf:

We look forward to your feedback and our own workshops under the heading "not a woman's business"!

Photo: Olga Rubakin

[Totalpoll id = ยป54304"]