It is difficult to imagine your home without electronics. When something breaks down, a sense of comfort disappears immediately. If the washing machine stops during a wash cycle, you need to act quickly.
If you stop during operation model has a display, it displays a fault code. Then with the help of instructions to determine the cause. Some of them can be independently removed, but in most cases it is necessary to apply to the master.
On the most basic reasons for the stop can cope on their own and run the machine at work:
- too much laundry downloaded or irregularly placed;
- incorrectly set wash cycle;
- bad lock access door.
To eliminate more complex reasons, use the services of a specialist:
- fault sensor, terminal blocks, connecting wires;
- failure of the electronic control unit;
- activated system of protection against leakage;
- engine malfunction PETN, drain pump.
minor fault
stiralki stop may occur due to electronics failure. In this case wrongly triggered sensors, electronics refuses to accept incorrect signals and stiralka hangs.
In this situation, you need 15 seconds to remove the power cable. Electronics will be reset to the initial state and resume work. If this does not work, check the other situation.
Overload or imbalance of the drum
Improperly loaded into the laundry drum can be the cause of cardiac stiralki. If the drum is greater than the permissible amount of laundry or items stacked unevenly, there is imbalance and stop.
The instructions indicate the allowable weight of things. If there is no automatic weighing stiralka linen, make a bookmark in strict accordance with the weights table. If the weighing function is provided, with the excess weight machine will not turn on.
In the case of incorrect bookmarks lingerie gets off lump rotates in one wall. Increases the load on the drum shaft and the vibration starts.
In this case, drain the water, proceed to download things and continue washing. If no other reason, the process goes well.
We made a mistake with the choice of regime
Washing machine hangs in the wrong selected program. Equipment to work properly, learn the nuances of its operation, as described in the instructions.
Do not attempt to simultaneously soaking and bleaching.
Clogged drain system
Sometimes the machine hangs during emptying. This could mean a clogged drain path.
First, make sure that there is no sewer blockage. If the water from the tub, toilet and sink drained properly, the sewer pipe is not clogged.
Check the drain filter in the bottom of the machine for the detachable or hinged panel. Clean it and rinse.
If the drain filter is clean, check the drain hose. To do this, remove it, clean the wire, if necessary, rinse with water under pressure and put into place. If the measures do not help, call a service technician.
The reason may be clogging in the drain pump or the drain hole of the tub.
serious damage
Tripped protection against leaks, do not close the door
Faced with the problem of water leakage due to damage to hoses, seals or connecting pipes, washing machines manufacturers provided them with protection against leaks. In case of water leakage the system operates and stops the process.
While the cause of the leak persists, the machine will not work to prevent flooding. Fault indication is displayed. Most often, the reason is failure of the discharge hose, which can be easily replaced by the customer.
The reason for a leak may be in a loosely closed hatch. If a bad set of rubber seals in the process of washing the hatch door can be opened. closing the door while the indicator goes off and the machine stops. In this case, open the oven door, wipe the gasket and close the hatch until it clicks.
The problem with the electronics or control unit
damaged electronics output during washing can cause a number of problems:
- in the washing process it is found that for a long time included one mode;
- washing machine does not switch modes;
- lit "rinsing" mode indicator, and the washing machine does not rinse.
In most cases, namely at the rinsing or spinning stops stiralka at failure of the electronics unit. The reason may be voltage drops, vibration machines, high humidity.
To control the washing process in machines sensors are installed. They monitor the water level, the balance of the laundry in the drum, temperature and engine speed.
If sensors with incorrect information supplied to the control unit, the machine stops responding and freezes.
Broke engine, PETN or drain pump
If a faulty motor, the drum stops rotating immediately. The water can be recruited, with some models even be heated to the desired temperature, but this work will cease. One can only switch stiralku to drain, turn it off and call the master.
To go with the washing mode to discharge mode: turn off the machine, select the appropriate mode and turn it on again.
Water is not discharged and stiralka stopped. Heating element can be damaged mechanically descaled or burn conductive heating filament. If weakened contacts, heating element will not be energized. Determine without fault diagnosis is possible by washing with high temperature, if the machine stops for some reason and the door glass is cold.
The latest models of washing machines fault diagnosis system more perfect. You can choose to diagnose the main components and to take measures so that the machine worked fine. For repair older models call a service technician.
