Error code on the display of washing machines Bosch

• Damage to handle. Replace this part.
• Improper adjustment sheds hatch. Set up tents to seal manhole covers.
• Inserting objects into a place fit the door. Remove the objects that prevent the closing of the hatch.

F02: the lack of water supply

If an error occurs, check:

• and plumbing between valve stiralka;
• the presence of water in the water;
• filler filter for blockage;
• water level sensor;
• inlet valve.

F03: problems with drainage water

To resolve this issue:

1. Check the drain filter and clean.
2. Check the drain pipe for clogging.
3. Inspect drain pump for operation.
4. Rang the electronic control unit.

In some models, these are characterized by failure code E5.

F04: water leak in the system

F04 error occurs because:

• Compromise the integrity of the intake hose. Replace it with a new one.
• Loose drain filter. Screw the pump.
• Damaged tray detergent powder. Install a new container.
• Cracks in the tank. Refer to qualified service personnel.

F16: loosely closed hatch CMA

F16 stiralka outputs error in the following cases:

• Broken lock. Check for serviceability.
• wiring damage. Rang her with a multimeter.
• Out of order guide. Change the detail.
• Incorrect work sheds hatch. Adjust the loop.

F17: the tank is no water

F17 Error in bosch washing machine may occur in the following cases:

• Closed locking device between the hose and the water pipe of the AGR. Open water flow.
• Contamination in the intake hose or filter. Eliminate the blockage.
• Faulty pressure switch. Change the water level sensor to work.

E17 Error in the washing machine bosch is the same as the F17. The appearance of the display E17 or F17 depending on the model. For example, E17 is displayed on the machine screen maxx5 series.

F18: bosch washing machine does not drain

In the event of a washing machine bosch error E18 or F18:

• Breakage of the drain pump. Check tangled around the impeller pump foreign objects. Prozvoniv pump motor winding and replace the pump in case of breakage.
• wiring damage. Restore the integrity of the wires.
• Blockage or improper discharge pipe connection. Clean clogged or properly connect the drain hose.

E18 depends on the model of the washing machine Bosch.

F19: Water heating error

Issued in these situations:

• Line voltage is not correct. Start washing at normal rates.
• Failure of the heating element. Replace it with a new one.
• temperature sensor breakage. Check the operation and replace if necessary.

F20: unplanned water heating

The reasons:

• Faulty relay supplies voltage to the heating element. Change of the control board.
• The sensor has broken, controlling the temperature of water in the typewriter mode. Change to the new sensor.
• Failure Control Module. Reflash control unit.

F21: not turning drum

Error F21, as well as E21 occurs due to the fact that he stopped spinning drum dryer. E21 is issued to the display the following reasons:

• Gust or stretching drum drive belt. Install the new belt.
• Engine wear brushes. Rely on the experts to replace them.
• drum lock foreign object. Remove the object and start the program.

F22: machine stopped heat water

• Blown heating element. Install a new heater.
• Worn or clogged pressure switch. Clean the tube pressure switch.
• Line voltage is below this. Wait for the normal stress and start SMA.

F23: system error is detected, load "Aqua-Stop"

F23 error in the washing machine bosch, like E23, appears if the MCA system detected a leak. In the event of F23 or E23, check for leaks details:

• inlet for water filling,
• a water level sensor,
• a hose connected to the water supply.

In addition, check the electronic control unit operation.

F25: faulty turbidity sensor

Appears on the display F25 is accompanied by:

• scaling of the turbidity sensor. Start the machine with the addition of special cleaning agents.
• Breakage pressostat or drain pump. Replace the defective part.
• Water low in the water purity. Install the filter cartridge in the water inlet hose.

A26: machine does not fill and / or drain

You can fix the machine by checking the pressure switch and wiring, according to which it is connected. Faults need to eliminate as far as possible or replace the damaged parts.

F27: broken work pressure sensor

The appearance of the error occurs due to the incorrect operation of the solenoid valve or a pressure sensor.

Details can not be repaired, so set in their place new ones.

F28: the flow sensor is faulty, the tank water is not supplied

The sensor monitors the ability to miss the right amount of water for a certain period of time. To solve the problem:

1. Install the new sensor.
2. Clean the blockage in the drain hose.
3. Measure the water pressure in the water.
4. Check valve operation.

F29: through the flow sensor does not pass water

Obstruction of water through the flow sensor occurs because:

• A clogged filter. Clean the filter element.
• Low water pressure in the water. Wait for the normal system pressure.
• Faulty pressure switch. Replace the part.
• Insufficiently tight closure of the door. Close the door more tightly.

F31: too much water in the tank

Oversupply of water in the tank may be due to failure of the water level sensor. The control unit does not receive a signal to close the inlet valve. The second reason: the fluid set in the tank due to improper installation of the machine. To solve the problem, check the pressure switch or install SMA in accordance with the instructions.

F34: the hatch door is not locked, no lock

The problem appears due to misconfiguration loading door. To solve the problem, configure or replace the details:

• door canopies,
• guiding the hatch to load linen,
• hatch latch
• lock cover.

F36: broken UBL

The reason for the occurrence of F36 can not only be breaking UBL, but also a violation of the integrity of the wiring. UBL replace or repair the damaged wiring. In some models, a fault code appears on the screen D07.

F37: no water heating from temperature sensor

The reason for failure is a failure in the electronic control. The problem solved by restarting the device. Also, the reason may be the failure of the sensor or its wiring.

F38: short-circuit temperature sensor

There are two causes of F38:

• offline required voltage due to damage in the wiring;
• thermistor failure requiring replacement.

F40: the car does not start

Washing machine gives F40 in the following cases:

• supply voltage is lower than claimed by the manufacturer. Provide normal stress.
• The power button is broken. Replace the switch.
• The power cord or plug is damaged.

F42: exceeded the permissible speed electric motor

In this case, there are two possible faults:

• Damage to the motor. Check the motor for operation.
• Failure of the tachogenerator. Replace parts.

F43: Motor blocked or not turning drum

The reasons that the motor can not turn the drum:

• jammed bearings;
• breakage of the Hall sensor;
• foreign objects in the drum, preventing normal operation.

To resolve the problem, contact a specialist.

F44: the motor rotates in the opposite direction

Most often, when such error fails reversing relay. In this case, replace it. F44 also appears when an uneven load of laundry.

F59: not functioning 3D-Sensor

1. Check sensor operation. Replace if necessary.
2. Correct connector loop connection to the module.

F60: flow sensor failure

F60 can be the result of faults:

• no pressure in the water;
• faulty inlet valve;
• failure of the drain pump;
• lock malfunction.

F61: the door is not locked, washing does not start

It appears in violation of the wiring board to Locking. Repair the wire and start the machine again.

F63: activation of functional protection

Functional protection is triggered if there was a software glitch. Refer to a specialist to repair the CMA to make reset software.

F67: failure controller

At failure of the electronic board, replace it. Boards can be repaired only if the processor and working only with help of a specialist.

E02: A critical error, there is a risk of fire CMA

The error occurs because:

• the critical state of the motor brushes, they need to change;
• broken bearings motor armature;
• tacho failure.

Such failures urgent need to eliminate to avoid the risk of fire.

E67: breakage control unit

E67 appears due for damage caused by the control unit:

• voltage drop;
• fuse failure;
• wiring damage.

Washing machines Bosch with self-diagnosis system simplifies maintenance. When the machine is itself an error, it can only decrypt and eliminate breakage. Do not assume a separate action to repair. To protect yourself and appliances, please contact in case of damage to the master.