🔨 it possible to put the tiles on the tile: the main provisions of the order and finish various bases

If you have to repairs room or outdoor area, which was previously laid tile covering, we offer to find out whether it is possible to put tiles on the tile without loss of strength properties of the base. To this end, it is worth considering not only the general provisions, but also the basic stages of the work.

Is it possible to put the tiles on old tiles - general

It is often difficult to say with certainty whether it is possible and necessary to glue the tiles on the old tiles. In this case, to assess the economic feasibility of the implementation of these works, as well as to find out the situations in which costs from this option to refuse. We offer more closely acquainted with the basic provisions that may affect your choice.

Justification feasibility

Arguing whether it is possible to lay ceramic tiles on the tiles, do not forget about the economic feasibility of the process:

• you can refuse to dismantle the old lining, which will reduce the cost of the preparatory work;
• the amount of dust and debris is significantly reduced;
• you can refuse to align the base and, as a result, the purchase of materials needed for this procedure;
• reduced time finishing works and their cost.

Attention! Reducing the duration of the process may be mentioned convention, since the rejection of dismantling the old coating will need to properly prepare the base.

Contraindications to work

There are situations in which the dismantling of the old tiling is preferred. Make it should be obligatory in the following cases:

• the floor is uneven and has a significant bias. In such a situation it is necessary to remove not only the facecoat, but also the screed;
• under the old covered are communication, access to which is not provided. In such a situation must be dismantled old coating, and then provide auditing hatches;
• there are voids. Such a base is not withstand operational load;
• tiles quite brittle and fragile. The presence of chips and cracks clearly demonstrates the need for the dismantling of the old coating, since it does not have sufficient strength and can not withstand the weight of the new. If cracked only a few elements, they can be removed, and the vacant place, align with a cement slurry.

Attention! Removing the old base should be performed without fail, if the number of corrupted cells exceeds 10 - 15%.

Is it possible to put the tiles on the tiles on the wall: the technological nuances

If you have quality on the walls, but obsolete finish, I think you have already thought about whether it is possible to put the tiles on the tile. The answer is yes, but with certain reservations. Before proceeding to the finishing works, be sure to check the status of the base.

Procedure for assessing the state of the old coating

Carefully inspect the base, to ensure no visible defects. Tile should not be unsteady, crumble. It is also unacceptable that some elements were poorly documented, as they may fall off at any time under the influence of the operational load. To test should test the surface of the hands, as well as to tap with a hammer.

Attention! The presence of wavering elements, or characteristic ringing sound indicates the presence of voids under the decorative coating.

stitches between finishing material must be in perfect condition. Unacceptable crumbling material. It is necessary to verify the existence of bias using a spirit level. If the wall is "filled up" to correct the situation with the help of tile adhesive will not work.

We offer watch the video to find out in order to validate the state of the base:

As the old wall tile put new tile, if the state of the surface found to be satisfactory

If you have already checked the status of the base and convinced of its strength, we offer to find out how to put the tiles on the tile. There is a certain sequence of actions that will help achieve a good result.

Giving old rough coating to provide the desired level of adhesion

Before you begin laying tiles on the tiles should prepare the base properly:

Illustration	Procedure
	On the surface of the walls remove existing contamination. You can use a soda solution. If the previously laid coating with a glossy surface of the glaze must be eliminated. To do this, use the grinder with grinding attachment.
	To improve the adhesion characteristics of the base coated on the surface primer.

Comment

Mikhail Starostin

Team leader repair and construction company "Home Premium"

Ask a Question

«Before proceeding to installation, it is necessary to prepare an appropriate adhesive. It is worth checking whether you can glue the tiles on the tile selected composition. "

Installation on standard technology

Installation work should be performed in the following sequence:

Illustration	Procedure
	If the wall is inclined or have irregularities alignment surface with a cement-sand mortar. Instead, the solution can also be used an adhesive composition. First, it is applied using a conventional spatula and uniformly distribute over the surface and then attach tool via a gear shape.
	Putting a tile to the wall and gently presses. If necessary, adjust the position. Crosses adjustable thickness seam between the elements.

Is it possible to lay floor tiles on the tiles: professional answer to an urgent question

In bathroom and the kitchen as a floor covering is most commonly used tiles, rather than laminate or linoleum. High performance characteristics allow the material to withstand high humidity and significant temperature fluctuations. On the eve of the repair, many are trying to find out whether it is possible to put floor tiles on the tiles. There are certain conditions under which this process is possible. We offer to find out in more detail in the technical intricacies.

Assessment of the old coating

Even if you understand in detail how to put tiles on old tiles, and then perform a quality installation work is not always possible to achieve a positive result if the condition of the coating does not meet certain requirements. From this method of decoration is to give in these cases:

• old flooring has numerous injuries on its surface is cracked and chipped. The new coating of a base such defects quickly begin to break down;

• floor space or ceiling height is low. Laying the second layer or the use of alignment plaster visually reduce the volume of the room;
• coating laid over communications. The audit state or replacement pipes lead to the necessity of mounting the two layers;
• there are voids. The new layer can lead to delamination of the old;
• the floor is uneven with a significant bias. It needs to dismantle not only the coating, but also screed.

In the absence of obstacles lay floor tiles on the tiles in the kitchen, in the bathroom or the toilet: a detailed list of actions

If the feasibility of the surface is new to the old is not in doubt, it's time to figure out how to lay tile tiles in the bathroom. There is a certain algorithm, which violate the wizard is not recommended. We offer to meet with a sequence of actions.

Revision coating and removal of unreliable elements

State audit coverage should start with a careful tapping of all the elements. This will reveal the emptiness and to identify elements with visible defects.

Attention! All damaged and poorly enshrined elements must be removed.

Then, using a level should ensure no bias. The presence of failures lead to the fact that over time, in this place the cover will sag and crack. The projecting parts cause buckling of the individual elements.

Scraping glossy surface

Glazed surface has low adhesion characteristics. Correct situation can base by stripping with a grinding disc or metal brushes.

Attention! Perform work with the windows open and a special mask.

During the surface treatment whole the glaze is removed, as well as various contaminants. Upon completion of all the dust and dirt must be carefully removed from the base.

Comment

Mikhail Starostin

Team leader repair and construction company "Home Premium"

Ask a Question

«If you do not possess a grinding disc or hard brush, improve adhesion characteristics is possible by drilling holes and by applying special notches. "

Preparation of an old ceramic floor

From the quality of the prepared base it depends largely on the life of the new coating. Therefore it is necessary to understand, on what surface you can put tilesAs well as how to prepare a foundation:

Illustration	Procedure
	If, after the inspection or during use several rings, it is essential to align the substrate with a tile adhesive was removed. The amount applied composition should be sufficient to form a smooth base.
	To align the tile adhesive can be used normally.
	It is applied to the prepared substrate "Betonokontakt". The composition should cover completely all the base. For the application, you can use various tools, including brush.

Installation on standard technology

After drying primer we place the tiles on the floor. Work is carried out in the following sequence:

Illustration	Procedure
	On the prepared surface spread a small amount of tile adhesive and distribute evenly over the floor surface using a trowel. The width of the formed strip should coincide with the width of the stacking material. Length must be sufficient for stacking 1 - 2 elements.
	We put the first element, ensuring the desired spatial position. Press down a bit. You can use the mallet to create an extra effort.
	Control the position of the laid track via level.
	We put the next item. control seam thickness with plastic parts.

We offer watch the video to find out in detail how to lay tile on tile:

Is it possible to put the tiles on old tiles on the street: we shall understand together

With finishing works are usually no difficulty indoors, but sometimes you can not say with certainty whether it is possible to put tiles on old tiles outdoors. This procedure is not always justified, and has certain nuances. However, this method is actively used, if the base has sufficient strength.

Checking stacking strength old coating

Quality-laid layer is the main criterion in the evaluation of the previous coating. Take a knife or a solid mount. If you delete or move the item coverage using them did not work, you can safely proceed to finishing work.

How to put paving slabs on the street, if the old coating strength is not satisfactory

If you have already checked the quality of the base, we offer to find out how to put tiles on the street. There are certain differences from the installation work on the premises.

The device is a new cushion of soil, gravel and sand

On top of the old tile is filled pillow consisting of compacted soil, sand and gravel. Each layer is compacted carefully to ensure a sufficient density.

That's not all of what lay paving slabs. Instead of sand cushion can form another type of substrate. It depends on the operational load and the location area.

How to lay tile on the street according to conventional technology: video instructions

When the base is prepared, one can start installation of paving stones. Sequentially stacked elements, the distance between which is controlled by means of plastic crosses.

We offer watch a video on how to lay tile on the street:

We think now that you know whether it is possible to put new tiles on the old one. Share in the comments, if you have managed to take advantage of this knowledge in practice.