When you create a comfortable home important role goes to furniture.
Assembly and installation of the sofa, cabinet and other furniture accessories - not the final step in the accomplishment. cabinet doors Adjusting balances furniture fronts.
Adjust yourself furniture hinges, it is easy without the help of professionals.
If the cabinet is filled up, it follows that the gap will be greater than at the exact location.
Adjust the door should be in the case of acquisition of a new subject or an old carriage in another room. Screws bumped for a long time from the constant use of poor-quality or original settings.
cabinet doors Adjusting balances furniture fronts.
You should also check and the moment when the additive of the facade under the correct cup.
Content
- 1 Adjusts furniture hinges with their hands
- 2 Four law hinges adjustment
- 3 Setting up planes
- 4 VIDEO: How to adjust the cabinet doors and furniture. Adjusting to the loops,
Adjusts furniture hinges with their hands
Adjust yourself furniture hinges, it is easy without the help of professionals. It should adhere to certain rules that prevent the formation of cracks on the facade, the gap between the box and the door, and the friction during opening. That is, the cabinet extended operating life.
Screws bumped for a long time from the constant use of poor-quality or original settings.
Most often, the correct adjustment is not possible at this moment, therefore, have to adjust the loop.
Four law hinges adjustment
Before you adjust, learn the rules in this area:
- Before you begin, furniture hinges are aligned vertical distance height of the door, and then set up on the formulation. If we apply the algorithm of actions, it will be much faster and easier to repair loops, as it does not have to go back.
- At the beginning of adjusting furniture hinges make sure the exact position of the cabinet on a level in all views. To control the position of furniture, use a special building level.
- The desired level is sometimes impossible to achieve. In such a situation it is guided by the distance between the doors. If the cabinet is filled up, it follows that the gap will be greater than at the exact location. Often used a standard measure of the gap, right standing furniture - 3-5 mm.
- You should also check and the moment when the additive of the facade under the correct cup. Otherwise, the situation will be bad shutters closed. Most often, the correct adjustment is not possible at this moment, therefore, have to adjust the loop. After learning the basic rules of repair of doors, it is possible to start correction of furniture screws, which is produced in several planes.
Extended operating life of the cabinet.
As you know, there are three planes: vertical (front), and the horizontal profile ( "back and forth").
Setting up planes
As you know, there are three planes: vertical (front), and the horizontal profile ( "back and forth"). Accordingly, they held adjustable hinges.
To control the position of furniture, use a special building level.
In this case it is sufficient to twist the second adjusting bolt for furniture accessories.
With the help of furniture hinges, you can change the position of the facade on the plane - this is useful when the door is bad close to the body.
Slightly loosen the screws and push on the door and pull it toward you, tighten the screw again.
To closet served for a long time, you need to adjust the hinges on the doors in all directions at once.
In this case it is sufficient to twist the second adjusting bolt for furniture accessories.
To closet served for a long time, you need to adjust the hinges on the doors in all directions at once.
Before you begin, furniture hinges are aligned vertical distance height of the door, and then set up on the formulation.
First, configure better vertically.
First, configure better vertically. Frontal regulation is necessary when the shutter is released from the overall picture of the furniture, or one located above the other (in the case where the model number of doors). This operation is carried out in four stages:
- It is necessary to open the door and find a loop, then remove the cap (if available).
- In all shelters tighten up the screws, which are located closer to the side. From these bolts depends on the vertical position. Screws initially need to balance, to decide on further action.
- Closed the door and pay attention to the overall situation with respect to the cabinet. If the upper angle directed to the right, it should be more tie bolts on the upper hinges, while as the lower weakened.
- To fully balance facade repeat step 2 and 3.
The durability of fixtures not only affects the regulation of hardware, but also properly selected fasteners.
Frontal regulation is necessary when the shutter is released from the overall picture of the furniture, or one located above the other (in the case where the model number of doors).
It can be assumed that the vertical setting is complete.
One type of adjustment, "back and forth", or profile. This method makes it possible to reduce, or on the contrary, increase the distance. Slightly loosen the screws and push on the door and pull it toward you, tighten the screw again.
Correct the adjustment will not keep going back.
To fully balance facade repeat step 2 and 3.
Adjust cabinet hinges can be a horizontal fashion.
Tighten the bolt to the corresponding corner of the door close to the frame. Inverse action (weakening) of the contrary alienate allow the angle of the frame. This adjustment is applied to the door when the shutter is hanging at an angle.
This adjustment is applied to the door when the shutter is hanging at an angle.
Slightly loosen the screws and push on the door and pull it toward you, tighten the screw again.
Independent work on the regulation of door hinges is beneficial and helps to save on maintenance, but also gives a lot of positive emotions from the result. Correct the adjustment will not keep going back.
Adjust cabinet hinges can be a horizontal fashion.
Independent work on the regulation of door hinges is beneficial and helps to save on maintenance, but also gives a lot of positive emotions from the result.
The durability of fixtures not only affects the regulation of hardware, but also properly selected fasteners.
One type of adjustment, "back and forth", or profile.
Closed the door and pay attention to the overall situation with respect to the cabinet.
This adjustment is applied to the door when the shutter is hanging at an angle.
