Cleaning the iron from the burnt tissue: Teflon or ceramic sole available means

Quality iron does not need special care - the problem may only occur if improper operation of this device. For example, if the iron is too hot iron things, not sticking to the correct temperature, at its base can form dark spots, which will make further use of the device impossible.

Cleaning the soleplate

Unpleasant dark brown plaque on the sole - it oplavivshiesya tissue particles, which ironed with a hot appliance. Of course, the dark spots are by no means a reason to throw away the iron from them is quite possible to get rid of with the help of simple manipulation.

Clean the soleplate at home There are many ways, and they are all pretty simple. purification method is selected depending on whether at the device sole - for example, with steel should first scrape off the solid layer with a knife, and then start cleaning. Teflon coating delicate, so it can not scrape.

Special pencil

It is a special tool for cleaning irons, which is sold in any supermarket or hardware store. Use it as follows:

1. Iron should be heated to the recommended temperature (usually the manufacturer advises to set the switch to the secondary division).
2. Cleaning pen is freed from its packaging and carefully rub their soles. Getting on the soiled surface means starts to drain from it, dragging the tissue and fused particles.
3. After processing contamination residues must be removed from the surface of the iron with a dry cloth.

You must know that the main active ingredient is a cleaning pen acid, Which is very sharp and unpleasant smells during melting, as well as reserves severe burns in contact with skin. Therefore, to work with him must be carefully and in a well-ventilated area. Under soleplate better to enclose the old unnecessary ragSince the dirt that flows from the instrument, leaving black spots and tends to harden upon drying.

Pencil is considered a universal remedy, as is suitable for cleaning aluminum, Teflon, steel and ceramic irons, if other information is not indicated on the packaging.

Salt

Salt - multi-purpose tool, since it can not only give a taste of food, but also to clean up the surface gloss different. Salt is also suitable for cleaning irons, with its use not one but several ways:

1. For procedures need polstakana salt which was evenly sprinkled onto the sheet of paper. Iron is heated to a maximum temperature and stroking them salt until complete disappearance of spots on the sole.
2. handful of salt is wrapped in a natural tissue (e.g., cotton handkerchief). Iron is heated to the maximum and it is carefully removed from contamination. But this method of cleaning is not suitable for devices with a Teflon sole.

paraffin candles

The paraffin candle is good at with light pollutionHelping to remove plaque from the surface of the iron. Candle wrapped in thick cotton cloth, heated iron and begin to carefully spend it on the sole of the device. Paraffin starts to melt and flowing down to the soles, drags pollution. In general, work with paraffin candles in the same way as with a special cleanser pencil.

If the iron is equipped with a steam functionWe need to further clean the hole and on the bottom by pouring water into a tank and the device several times using steam blow. As the wax, flowing down from the iron gets into the hole for a couple, this technique will help prevent stains on his clothes, which will be ironed in the future.

Peroxide, ammonia and vinegar

Vinegar as table salt is used in several ways:

1. To remove a weak fresh raid cloth slightly moistened food vinegar and rub it contaminated sites.
2. If the particles are burnt tissue time to harden a piece of fabric impregnated with abundant vinegar and leave it on the iron on all night. On the morning of contamination softens, and it is easy to remove the remnants of dry hard tissue.

In the same manner and using citric acid solution (1-1.5 2-3 sachet article. warm water).

Ammonia and hydrogen peroxide wetted fabric and wipe it soiled areas of the sole. You should know that ammonia should not be applied on a hot surface, so all manipulations with it are held only after the iron cool down completely.

Gidroperit and baking soda

Soda - a versatile tool that can clean the most serious pollution any surface which is not afraid of the contact with abrasive materials. Therefore, such a purification method does not fit to Teflon coating.

To clear soda soleplate, apply it on the contaminated surface and rub lightly, then remove the remnants of plaque with a damp cloth.

gidroperita Tablets typically used as cleaning pen. To this end iron and heated tool applied to problem areas and finally wiped with a sole piece of wet tissue. All procedures should be carried out in a well-ventilated area, otherwise the room for a long time soaked in caustic unpleasant odor.

Processing Teflon soles

Devices with Teflon soles are considered modern and functional, they are convenient to use and easy to smooth any fabric. To clean the iron with Teflon coating, have to comply with certain accuracy, because it is quite gentle and careless actions can cause irreparable damage to the sole. Best to use special sponge and pencilsAdhering indicated on the package recommendations manufacturer.

An alternative method of purification of Teflon in the home is the surface treatment vinegar essence. When working with this material should be very careful, t. K. It is in contact with skin and mucous membranes severe burns. A small piece of cloth moistened with the means and carefully wipe the contaminated surface. If this does not work, the essence impregnated cotton cloth and iron it with heated iron.

Removal of burn-ceramic surface

Such a device is almost as gentle as Teflon, so to clean ceramic soleplate also recommend the use of special tools - pencils and sponges. If they are not, and contamination must be removed immediately, to cleanse the ceramic surface in the home using a few rapid methods:

• Soap - a means of gentle, yet quite effective. Slightly dried up the device you need to rub the sole soap, leave for 40 minutes and wipe the surface with a piece of clean cloth.
• Quite copes with Prigara ordinary toothpaste. It should be applied to the heated sole, leave to dry and remove the remnants of cloth pollution.
• Adhering particles reflowed tissue can be removed with acetone. For this sole device wipe soaked in it with a soft cloth.
• Citric acid and juice are also well purified by the surface of the iron. Lemon juice diluted with a little water, moisten the cloth in the solution and rub it contaminated the sole.

To clean burnt iron, you need to follow all the rules of care for this device and choose ironing each article of clothing the right temperature.

How to clean iron

retain