Methods for cleaning the soleplate of metal penetration: how to clean a home, application folk remedies

The process of ironing and laundry - an integral part of family life, and the modern iron long since become an indispensable tool for all housewives. Most irons models from around the world provides assurance to the consumer that the sole of the ironing device has a non-stick coating, but in reality it is not so.

Due burnt the soles can be spoiled by good things. There are many affordable ways to clean burnt iron, without using expensive means, and in a few minutes to return soleplate cleanliness and shine.

Materials of construction for the soleplate

Modern manufacturers battling for the confidence of their customers, try to use for the manufacture of soles Only high quality alloys. Working iron surface can be made of such materials:

• Aluminum. Most capricious to care material, is susceptible to scratching and adhesion of synthetic fabrics.
• Stainless steel. Such a surface is unpretentious in operation, it can be cleaned in any way as an apprentice.
• Ceramics. For cleaning of the sole use of a special pencil. It is also permissible to use mixtures of soft non-abrasive, toothpaste, hydrogen peroxide, soda. The main condition - not to clean ceramic sole sponge or brush.
• Cermet. The same care as that of the ceramic samples.
• Teflon. This aluminum surface with a further layer of Teflon. Sole require special care, it is necessary to purchase a special sponge that soaked in vinegar. Strictly forbidden purified by Teflon iron salt or toothpaste.

Methods for cleaning the soles of a home

There are some rules and guidelines for cleaning irons. In any case it is impossible to clean the soleplate with sharp objects. It is recommended to wipe the iron with a damp cloth after each use. Before you begin to clean the iron, determine which method is suitable for your equipment.

cleansing salt

Effective and accessible to every treatment method. table salt used in two different ways.

1. Half shallow cup salt is poured onto a sheet thick paper, the layer is leveled. Preheat the iron to the maximum possible temperature. Lead salt by weight of the soleplate until the deposit has not yet completely eliminated.
2. A small handful of sodium chloride is wrapped in a fabric made of natural material, this may be a conventional handkerchief. Wait until the ironing apparatus heated, after which the obtained salt pouch carefully remove dirt.

hydrogen peroxide with carbamide

As for the purification of burnt stick coating may be applied tablet form gidroperita. Nagar with a heated iron easily removed crushed tablets. Gidroperita for removing residues using a damp cloth. After the manipulation should be thoroughly ventilate the room to get rid of the pungent peculiar smell.

Shoe sole citric acid

citric acid solution copes with both scum, and with the burn-sole. The beaker is stirred with water acid tablespoon. Pour the resulting solution into the compartment for water. Remove carbon deposits can be if ironed fabric, spray lemon water. The same solution is suitable for cleaning holes where the steam comes out - this requires a cotton swab.

The use of vinegar

One-third of the tank, which is filled with water, filled with water and vinegar solution. Include mode maximum iron temperature and left in the vertical plane by 15 minutes. It should be borne in mind that during this time period it will turn off a few times to cool down and heat up again, to intervene in this process is not necessary.

After that, under the appliance con basin, in which water will flow. Iron must be positioned horizontally. Then, holding the special button, gradually releasing steam. As a result, from the holes will start to come out rusty water.

Continue appropriate action until the selection is not yet completed rusty drops. Carrying out the described steps, the iron is poured glass of pure water and again launch mode the maximum temperature. This will remove the remaining scale and vinegar. It is necessary again to arrange the iron in a horizontal direction above the capacity of the water and produce steam. At the last stage, the water is drained, and the outsole is wiped with a dry cloth.

Cleaning gray

Clean the soleplate can be gray, rather incendiary strip, which are equipped with all matchboxes. Better if it will be the new boxes. Preheat the iron and spend them in a sulfuric strip. For a more thorough cleaning is recommended to rub the surface of the strip of metal iron. Dry cloth remove sulfur residues.

The use of soda

A popular way to deal with all kinds of contaminants both on clothing and on household appliances. In the water were dissolved tablespoon of sodium carbonate to a consistency reminiscent of thick cream. To clean the sole, it is applied to the mixture. The device is pre-heated to a hundred degrees. Ten minutes after the application of a soda to be erased from a soft cloth fibers.

Toothpaste

Another alternative embodiment, which has a similar action effect with soda. It should be noted that the toothpaste has been applied not only to preserve the purity of the soleplate, but also for the care of jewelry and metal utensils. Before applying the coating detergent should be a good warm up. From a tube onto the sole of a small amount of pasta is extruded and begin to rub soft toothbrush, being careful not to damage the coating. Removing plaque, the sole rinse and wipe with a dry cloth.

Candle of wax

Paraffin Candle - is not only a source of light in the room where the light is turned off, but also an excellent means for the purification of iron from prigarnyh spots. Best of all, this method is suitable for ceramic coatings. Candle wrapped in cotton cloth and ironing appliance include the maximum mode. The resulting bundle is rolled on the heated ironing plate. Naturally, the wax will melt, so pre-prepared bowl, Which will drain the molten paraffin mass. Denim should be quite thick, the wax is not leaked to the outside and not stuck in the steam holes.

Special pencil

Those who are skeptical to all sorts of national methods cleaning ironsCan buy at the hardware store a cleaning pen. Through this means, not only burning-cleaned, but also to improve some properties of the ironing surface. High-quality pencil able to make a sole smoother, removing any traces of metal penetration. How to use this tool?

1. The first step is to heat the iron.
2. It is advisable to turn the appliance, to avoid having to perform the entire process on weight.
3. Spend some time by means of red-hot sole, most importantly, remember that the pencil consists of a low-melting components. In connection with this, it is necessary to distribute it around the perimeter of the working surface of the iron.
4. Do not clean the iron particles from the remaining pencil good things, otherwise they will remain neotstiryvaemye spots. Better to take a rag, which is not a pity to throw.
5. At the maximum temperature range to iron unnecessary tissue, releasing a little steam. Thereafter, purification can be considered completed.

How to prevent fouling

In the department of home appliances, in addition to the iron, you can buy him set of special linings to protect the ironing surface. Such strip prevents formation of coke, and also prevents the receiving holes when ironing delicate fabrics and garments with a pattern.

A popular way to more well-known since the Soviet times, involves the use of gauze or thin cotton cloth during ironing. The selected material is placed on the item and begin stroking over it. The effect of stripping is possible, if the fabric is well moistened with water and wrung out. Wet material in the same way they spread on clothes and iron until it dries. This technology allows you to protect the ironing surface from undesirable soot.

wardrobe elements, which have different patches, stickers and rhinestones are best ironed previously inside out. So do not spoil the look of things, and the device does not have to be cleaned of contamination.

We can not forget about the fact that every single tissue requires ironing his regime. When people start to iron synthetic thing with the use of the maximum temperature, then ensure that the iron does not form deposits, almost unreal. Probably not such irons, wherever indicated, what temperature to set for a particular type of tissue. If, however, such information is not provided, it is necessary to initiate the procedure with minimum heatGradually moving the lever on the large circular mark. Let ironing take more time, but the thing and irons are best preserved.