How to wash the tiles on the floor from the grime?

Tiles are one of the most durable floor coverings for bathrooms, kitchens and other rooms where dampness appears from time to time. Durable, aesthetic, resistant to various impacts and substances, with due care, tiles will last for many years and will always look like new. In this article, we will tell you how to wash the tiles on the floor from stale dirt, for example, after repair or after a long absence of regular care, so that there are no ugly divorces, plaque, scratches left on it.

to the contents ↑

Basic rules for tile care

Ceramic tiles were familiar even in Ancient Rome. Thanks to its merits, which can not be overemphasized, tiles still decorate our home.

To ensure that this unique coating lasts for as long as possible, without losing its appearance, follow the following rules:

1. Daily sweep or vacuum the floor to remove dirt, food residues, other debris that accumulates on the coating. Garbage, which remains in a damp room for a long time, is able to turn into mud.
2. If there are no stains on the coating, it is sufficient to wipe it off periodically with a damp cloth.
3. After damp cleaning with plain water or detergent, be sure to wipe the floor dry. Thus, you not only prevent the rapid accumulation of dust, dirt on the tile itself, but also the seam between the tile and the floor. Accordingly, less likely to be puzzled by the question of how to wash the tiles on the floor from the grime.
4. Clean out all spills in a timely manner. All spills from juice, tea, coffee or other liquids are not only very quickly absorbed into the seams between the tiles, but they are also very sticky, as a result, dust and dirt are quickly attracted to them.

Important! Against dangerous stains, use a disinfectant. For example, if a domestic pet has defecated on a tile or you have dropped raw meat on a coating, spray the soiled area with a disinfectant, immediately wipe it off.

to the contents ↑

Than to wash the tile on the floor?

Before you start cleaning the tiles, you need to determine the type of contamination, as this determines the choice of tools and tools. If the tiled floor can be wiped out in a few seconds, then with the joints all much more difficult. Sutures accumulate all the contamination, respectively - become an ideal place for reproduction of fungus and mold. As a result, the question arises, how to wash the tiles on the floor from the grime?

Most often joints suffer from the following contaminants:

• Remains of funds, materials after repair.
• Pieces of food.
• Dust, dirt brought from the street.
• Dirty water. Remains of detergents.

Important! With time, in the process of exploitation, the grout begins to darken, besides, foreign particles adhere to the contaminated joints. If the flooring is not cleaned in time, then to the problems of cleanliness and aesthetics, the problem of the fungus will also join.

Tools, like tools, in order to wash the tiles on the floor from the grime and the seams between the modules can be different. Everything depends on the degree of neglect and type of pollution. Sometimes you can do with folk remedies and improvised materials, and in some cases only household chemicals and a rigid brush will solve the problem.

to the contents ↑

How to clean ceramic tiles from grease and dirt?

If the white tile on the floor is no longer pleasing with its fresh appearance, then use the following tools:

• Vinegar.
• Citric acid.
• Ammonium alcohol.
• Liquid for washing dishes.
• Soda.
• Chlorine or "Whiteness".
• Washing powder.
• Kerosene.

Use the above tools as follows.

Vinegar

Dilute 0.5 cups of vinegar in 4 liters of water. Rinse the floor with a solution. Rinse the cover with clean warm water, wipe dry.

Important! Do not use vinegar and other aggressive chemicals to clean the marble cover.

Citric acid

Sponge the kitchen sponge gently into citric acid and treat the problem areas to wash the tile on the floor from the grime. Then rinse the area with clean water, wipe dry.

Important! The use of citric acid is effective when removing stains from grouting. However, if the seams between the tiles are not protected, then give up acid - use a more gentle means.

Chlorine

For white tile use usual bleach or "whiteness".If the chlorine powder, then dilute it in water according to the instructions. Pour the solution into a spray gun, spray on the surface. After 5 minutes, clean the problem area with a brush. Rinse the floor with plain water, wipe dry.

Important! When handling the surface with bleach, adhere to safety measures: work only with rubber gloves, do not close the door in the room, turn on the hood or open the window to avoid the effects of the odor of the product.

Detergent

1. Remove stains from liquid spills with a detergent paste:
2. Pour laundry detergent into warm water in a 1: 1 ratio.
3. Duster cloth dust spot with medium.
4. After 5-10 minutes, wipe the area with a soft sponge and wash the floor with clean warm water to remove the detergent residue.
5. Repeat the process if necessary, after which, wipe the floor dry.
   

Foam

Tile from mold will relieve ammonia from ammonia. It will also help to wash the tile on the floor from the stale dirt:

1. Prepare the solution: ammonia - 1 part, water - 1 part.
2. Wear rubber gloves to protect your hands.
3. Take a soft brush and clean the tile with a mortar.
4. After treatment and removal of mold, rinse the surface with clean water.

Kerosene

Stains of rust and building materials will remove kerosene. Wear rubber gloves and moisten a rag in kerosene. Wipe the problem areas with a cloth and rinse the surface with warm water. Repeat the process if necessary.

Useful advices:

1. Rough, embossed or dark ceramic tiles, try to clean from the glue( grout) as soon as possible. Use for this purpose the vinegar solution: for each liter of water - 50 ml of vinegar. Wipe the contaminated areas thoroughly with a solution, pay special attention to the joints between the tiles. After treatment, rinse the surface several times with warm water and wipe dry with a soft cloth.
2. If there is no special tile brush, remove the dry grout with a piece of light wool or felt. After removing the grout, wash the floor with vinegar.
3. Glossy tile after grouting can not be cleaned with abrasive powders and metal brushes, as it will lose its luster. Use only brushes with soft bristles and liquid agents that do not damage the surface of the tile.
4. Do not use household chemicals designed to clean the gas stove and sanitary ware, to tidy the tiles. Before using this or that "chemistry", be sure to read the instructions for use.
5. To ensure that the joints between the tiles are not damaged, during cleaning and surface treatment, cover them, for example, with epoxy paint. And remember that unprotected seams can be damaged by solutions containing acids.
6. In order to wipe dry the tiles, use microfibre or terry( bamboo) towels.

to the contents ↑

Than to wash the seams between the tiles?

An entire arsenal of tools is used to clean seams from contamination. Of course, everything depends on the degree of neglect and type of pollution.

To wash the tile on the floor at the joints and seams you may need the following materials and tools:

• Old toothbrush.
• Chaber.
• Rubber spatula.
• Eraser.
• Household chemicals: powder, spray or gel.
• Dishwashing liquid.
• Soda.
• Whitening.
• Hydrogen Peroxide.
• Protective gloves.
• Clean water and a container for it.
• Sponge.
  

How to clean the mud at the joints?

If the contamination is not too serious, then use the handy tools:

1. Eraser. This method is suitable for cleaning a small area of ​​the seam. Walk the eraser along the seam and remove the stain. Use a white or pink eraser.
2. Soda. Prepare the pasta from soda and water. Apply the product to the seam with an old toothbrush. Wipe the paste well in the seam. If the contamination is old, give the paste a few minutes to get into the stain, and then start rubbing it. After treatment and removal of contamination, wash the joint with warm water.
3. Bleach. If there is a white seam between the tiles, use bleach to clean it: dilute the product in water, in a 3: 1 ratio. With a toothbrush or the edge of the sponge, clean the joint with a mortar. After treatment, rinse the surface with warm water to remove bleach residues. Once the surface of the floor has dried, apply a sealant to the seam so that the dirt can not be absorbed into the joint in the future.

Important! Do not use bleach for colored seams, as this can discolor them. When treating the joint with bleach, make sure that the product does not get on the surface of the tile.

Useful advices:

1. To clean the joint, purchase a special joint brush in the household chemical shop. So it will be easier for you to wash the tiles on the floor from the grime.
2. If you find it easier to work with household chemicals, then you will get special tools designed for washing not only tiles, but also joints between tiles. Such products are produced in the form of a cleaning powder, a spray or an active gel. Apply the selected remedy to the problem area and leave it for a few minutes. Then remove the remnants of chemistry with clean water.
3. In order to refresh and bleach the seams between the tiles, use the following mixture: mix the dishwashing gel, hydrogen peroxide and soda until a creamy gruel is formed. Proportions take approximately equal. Apply the compound to the seams with a toothbrush. Slightly rub and leave for a couple of hours. The gel will remove grease and dirt, and soda and peroxide will give the seams a fresh freshness and return the former whiteness. After treatment, rinse with fresh water.

to the contents ↑

How to get rid of fungus and mold?

In order to prevent the fungus from affecting the fungus, the surface must be treated regularly with antiseptic preparations. But if the matter has gone too far and harmful microorganisms have already settled on the darkened seams, then simple methods of purification will be powerless.

To wash the tile on the floor from the grime and mold, the following tools will come to the rescue:

1. Antifungal agent for cleaning joints. Spray the problem with the preparation and leave for half an hour. After the treatment, thoroughly rinse the area with warm water and wipe dry.
2. Bleach. Dilute the vehicle in water at a ratio of 1:10.Wipe the contaminated area and rinse with water.
3. Bura. Prepare a solution: a glass of borax for three liters of water. Apply the solution to a dirty surface and rub it on the hard side of the sponge. Do not flush the product, remove it with a dry cloth.
4. Soda. Clean the problem area with soda and remove not only the mold itself, but also the unpleasant odor left by microorganisms.

Seam repair

The best way to fight mold and fungus is to completely replace the affected area. Proceed as follows:

1. Clean the affected area with a scraper.
2. Walk through the joints with antiseptic soak to protect the floor covering from spreading germs.
3. Allow the preparation to dry.
4. Dilute a small amount of grout.
5. Cover the joints with loose seams.

Important! Carry out the renewal of the joints regularly, because in addition to contamination, there is a gradual washout and destruction of the material. This is reflected not only in aesthetics, water resistance, surface strength, but also in hygiene.

to the contents ↑

How to wash the tile on the floor after repair?

The joy of completing the repair can be overshadowed by the fact of dirty floors and cleaning, if the masters did not really keep clean at different stages of construction work. It should be noted that the tile must be cleaned immediately after the cement slurry or "liquid nails" is applied to it. But if all the same, the building materials fell on the tile, then they will have to work hard to remove them.

The choice of means and methods to wash the tile on the floor depends on the following factors:

• Surface of the tile.
• Nature of pollution.
• Time of staining on the surface.

To clean the tile after repair, adhere to the following recommendations:

1. After repair from tile, it is necessary to sweep the dust with a soft brush or vacuum. Do this as soon as possible so that the dust and dirt do not stick into the surface of the coating. After dry cleaning, proceed to a wet cleaning.
2. The stuck slices of the mortar must first be mechanically removed with a smooth, well sharpened chisel or sharp blade, then treat the problem areas with a special solvent.
3. Cement, putty and other similar materials should be removed from the tile with a plastic spatula and water. Rinse the paint with a solvent.
4. Remove the frozen lime with a solution of vinegar. As an alternative - vegetable oil. In warm water, add vegetable oil and wipe the solution with a white coating on the surface. Then wash the tile with a dishwashing detergent.
5. If during the repair process the tiles are only stained with building dust, then clean it with detergent, vinegar or ammonia. About how to apply these tools, we wrote above.
6. If there is a coating on the coating that is not removed with detergents, then glue felts to a pad with a handle and rub the surface with an improvised tool.
7. Tile glue and other similar materials should be removed with Silith, Cinderella, etc.
8. If the trowel for tiles has become embedded in the grooves between the tiles, then treat the seams with fine-grained sandpaper.

Important! First, try all the methods of cleansing in a small inconspicuous area. If the surface of the tile does not deteriorate, apply the product on the entire surface.

Keep track of the condition of tiles and joints regularly. Once a week, with special tools, clean the tiles from dirt, and you will extend the life of the outdoor decorative coating for many years, and at the same time protect the house from fungus and mold.