How to eliminate the vibration of the washing machine during spinning?

bearings Your washing machine worked without problems, when you suddenly started jumping, bouncing and making absolutely un-musical sounds? It is possible that she got up wrong. However, these "symptoms" may indicate a serious problem that must be immediately eliminated. We will understand what causes these phenomena are caused and how to eliminate the vibration of the washing machine during spinning.

to the contents ↑

Why did the machine start jumping?

There are many reasons for jumping and high noise. Here are the most common of them:

• Contact of small items between the tank and the drum. For example, we often put clothes with clips, pins or coins into the unit.
• When transporting styralki transport bolts were not unscrewed.
• Incorrect distribution of laundry in the drum unit. This problem concerns old models of washers. New modifications are equipped with automatic distribution of laundry in the drum.
• Motor failure.
• Incorrect installation of the machine on the supports.
• Bearing failure.
• Malfunction or heavy wear of shock absorbers and springs.
• Deformation of the counterweight or loosening of the fastening.

to the contents ↑

How to find the malfunction?

There are a lot of problems, so it's quite difficult to find out exactly what caused the vibration and extraneous sounds. Therefore, it is more rational to exclude the simplest variants.

So, let's start analyzing the problems, so that the vibration of the washing machine can be eliminated:

• See if the laundry in the machine is curled into a knot. This is a fairly frequent phenomenon( for example, small objects fall inside the blanket).
• Check if you put too much underwear on the machine. For each model, the values ​​of the limiting mass will be different.

Important! Things intended for washing should not occupy more than ⅔ a drum - this affects not only the jumps of technology, but also the quality of the laundry itself. In this respect, modifications of the styalki equipped with a display are very convenient, which, if overloaded, produce UE or UB errors.

to the contents ↑

How to install the styralka correctly?

Vibration can often be caused by an incorrect installation. This happens when the owner tries to mount the device by himself. The most common mistake is when the owner completely forgets about the transportation bolts. Sometimes bolts are removed, but the unit is installed on an uneven or slippery surface. The machine vibrates during the washing process and produces a strong noise.

How do I eliminate the vibration of a washing machine in this case?

1. See if the transport attachments are removed. They are necessary when transporting the machine to fix the drum. If you forget about them, then the drum will rotate, but with much more wear and tear, and the device will vibrate and jump while you work.
2. Do not forget to make sure that the installation of the machine has been made to the exact level. To do this, you can adjust the height of the legs. In the process of pressing the device comes into resonance and not just vibrates, but literally jumps, moves around the room. For this reason, it is not advisable to leave the washer unattended.
3. After the installation is done, check if the machine is stable. Any precarious situation leads to jumping and extraneous sounds.

Important! Even if you entrust the installation of equipment to professionals, it is advisable to check the listed nuances yourself. This saves you time: both your own and others'.Test the operation of the machine after it is installed.

to Contents ↑

Shock Absorber Fault

Inspect the shock absorbers carefully to mitigate the movement of the drum and to suppress vibration. With strong vibrations and jumps, it may be necessary to replace the shock absorbers. The situation is complicated if the springs are out of order. It is necessary to replace both springs and shock absorbers.

Important! Typically, wear is not the same, but both shock absorbers are subject to replacement, for a balanced load distribution.

How to proceed:

• Look carefully, maybe small things got under the drum. If they are there, then they will have to get them. To do this, you will have to make something like a metal hook, to extract clattering gizmos.
• If this attempt was unsuccessful, then it is necessary to disassemble the unit: remove the drum, the heating element, and possibly other components.

Important! If you do not have this experience, it is better not to test fate, but to call a master from the service center. You will save both time and money. In any case, the call of a specialist will be much cheaper than buying a new device. In addition, the question of how to eliminate the vibration of a washing machine will not worry you for a long time.

to the contents ↑

Attaching the counterbalances

One of the reasons that the machine starts to shake and jump is problems with attaching a counterweight. To eliminate it, you will need: a screwdriver, a key and pliers.

Important! Assess the condition of the counterweight. The counterweight is a weighting agent made of different materials. A counterweight is installed in the upper and lower part of the washing machine. They are made of concrete, cast iron or other metals.

The further action algorithm is as follows:

1. Inspect the mounts. If they blabbed, then they need to tighten.
2. Trying to tighten the mounts failed? Acquire and install new ones.
3. If the deformation of the weighting agent itself occurred, then you can not do without its replacement.

to Contents ↑

Defective

Bearings One of the reasons the machine jumps is bearing failure. Replacement of bearings is not an easy process, therefore it is desirable to call a specialist who will professionally perform this work.

Metal from which the bearings are made, eventually becomes unusable:

• When the bearings are destroyed, the machine starts to work noisily at first, and then the drum completely jams. If the bearing just started to break down, "diagnosing" is not easy. As a rule, professionals determine the wear of parts, catching the slightest extraneous sounds.
• And if the bearing is seriously damaged, you can move the drum. If he is too mobile, then this is the signal to call the wizard.

Thus, there are many reasons for vibration of the styralka. Soviets, how to remove the vibration of the washing machine during spinning, is the same. But you need to remember: the more careful you are with the technique, the more strictly you follow the instructions for using the equipment, the less unpleasant moments it will deliver to you.