Replacing the drain hose of the washing machine

To date, there are a huge variety of models of washing machines, differing from each other in price, quality and functionality. But it does not matter which one you choose, because this technique can also break down and fail. For this device to work continuously, it is necessary not only to look after it appropriately, but also to take care of the state of all its parts and mechanisms. The most common service related to this technique is the replacement of the drain hose of the washing machine, because experts recommend that you always install a corrugated hose to drain and recruit water. If you study the instructions carefully and have at least some skills of repairing such equipment, you can replace and install this device with your own hands. And how to do it - we'll look further.

to Contents ↑

Can I replace the drain hose myself?

Of course, replacing the drainage device is a little more complicated than filling, but it is still possible. In the case of a filling hose, you only have to work outside, but to replace the drain hose you will have to partially disassemble the washing machine. The fact is that it is connected to the drain pump, so you need to get to the inside of the case.

Important! Depending on the model of technology, the hose can be located at the very bottom of the back wall or vice versa - go out from the top to the outside.

To understand where it is, you need to do the following:

1. Remove the bolts on the rear panel.
2. Push the cover aside.
3. Remove the wall for further work.

As mentioned above, different washing machines have absolutely different hose position and internal structure, so we will see how to change the drain hose in the washing machine Samsung, Zanussi, Bosch, Electrolux, Ardo, Siemens and many others.

to the contents ↑

General rules for installing a drainage device in washing machines

• The main thing to remember is that any model of such equipment is an electrical appliance and operates from a network. Hence - in the first place it is necessary to disconnect it from the power supply.
• Before this, we check whether the previously set washing mode is completed. If the washing process is completed, you can safely unplug the device from the network.

Important! Do not bend or twist the hose during all work.

• Then you need to turn off the water supply, namely, disconnect the flexible tube for water supply using a wrench or pliers.
• It is necessary to remove, wipe the rubber gasket.
• Then the pipe is attached to the rear wall. Place the plug in the place where the hose is fastened.

That's all the preliminary work that needs to be done, and then the installation itself follows.

to contents ↑

Features of the drain hose in modern machines

Automatic replacement of the drain hose of the washing machine provides full access to the internal unit of the unit.

The corrugation is usually fastened close to the drain pump inside the casing. To make a replacement, the hose must be removed from the body and from the pump.

Important! To make it more convenient to work, it is better to remove the top panel.

Advice:

• The corrugated pipe is disconnected from the water pipe and the outflow tube is removed.
• You have to drain the water.
• Do not tilt the device.

And now we'll take a closer look at how to replace this important element in today's most popular washing machines.

Installing the drain hose in the Ardo, Indesit, LG, Samsung, Candy, Ariston, Beko

devices. Now we will figure out how to change the drain hose in the washing machine Samsung, Indesit, Ardo, Beco, because their internal arrangement and functionality are very similar.

Important! In such models, one can get close to the hose only through the bottom.

This is done as follows:

1. Remove the plinth panel.
2. Without unnecessary hassles we remove the drain filter from the pump. In advance, we prepare a container for draining the remaining water and a rag.
3. To freely perform all necessary work, it is necessary to move the machine away from the wall.
4. Remove the fasteners holding the cochlear, and then it.
5. Relax the yoke, disconnect the old hose.

Important! Remember carefully how the obsolete element was attached, it's best to take a picture of it.

1. Unfasten it and take it out.
2. We are installing a new hose, using a clamp, fix it directly on the pump.З
3. then all the previously removed items are returned to the site.

Important! Before using the machine again, make sure that all joints and connections are tight. When you connect the hose to the sewer, it is recommended to check both sides for leaks.

Replacing the drain tube in Zanussi and Electrolux

machines In these models, replacing this element will be more difficult, as it will take longer to work.

Important! Here you can not approach it from the bottom, so you'll have to completely remove the back wall.

The whole work can be divided into several stages:

1. First we unscrew the bolts with the help of which the back of the device is fixed. But immediately it can not be removed, because it is held by the priming valve. Therefore, it is necessary in the first place to detach the valve itself and remove it, but only then the lid itself.
2. Separate the pump from the hose by loosening the yoke as described above. Unfasten the sink, put it aside.
3. We get a new hose, lay it in exactly the same way as the old one was connected, that is, we connect it to the pump and fix it with a clamp.
4. Securely attach the hose to the body itself and return the back cover to its place, on top of it the fill valve and the top cover.
5. Finally, we connect the device to the sewerage and water supply, and also run a test wash to check how well the work was performed.

Recommendations for installing a drain hose in AEG, Siemens and Bosch machines

Replacing the drain hose of a washing machine of any of these manufacturers requires maximum strength and concentration, since all of their models have a complex design that does not allow easy access to the element in need of replacement.

Important! In this case, you need to remove the front of the device, and this is a very difficult and complicated process.

It happens this way:

1. In the first step, you must remove the container for the powder.
2. Then remove the lower part, merge to the last drop all the water.
3. Detach the cuff from the machine wall. To do this quickly, you need to use a slotted screwdriver and remove the yoke, which, in fact, it holds. After - remove it.
4. We unscrew the bolts holding the front part, which are at the top and bottom. After that, it hangs on the hooks, but you can not shoot it right away, because it will also be held by the wires going to the lockout device. There are two options for solving this problem:
   • twist the bolts that fix the door lock;
   • push the front side to the side and pull out the required wire.
5. Next, lift the wall and pull it to yourself, so that it disconnects with the hatch.
6. The process of removing the old and installing a new hose is no different from the previous versions. Also, the pump is disconnected first and the clamp is relaxed. We change the old hose to a new one, but do not hurry to attach it. On the pump we put on the end of the corrugation, fix it with a yoke.
7. The hose is attached to the body according to the already known scheme.
8. We check carefully the tightness and reliability of each connection. We put on the front cover, insert the lock and return the cuff to its original position.

to the contents ↑

How to replace the drain hose in models with vertical loading?

Actually, the replacement of the drain hose of the washing machine, where the laundry is loaded not from the side, but from the top - nothing much different from the processes described above. The only difference is the need to remove the side wall:

1. The work begins already according to a known scheme with the removal of bolts located on adjacent sides of the device, that is, the back and front walls.
2. The side panel is easily removed and set aside.
3. Find the pump, loosen the clamp, remove the hose from the drain pump.
4. Then disconnect it from the case and by analogy lay a new hose, also connect to the pump, attach the clamp.
5. We put back the "side", we do not empty the laundry.
6. In case of detection of leaks immediately eliminate them.

Now you have an idea of ​​how the washing machine's drain hose is being replaced. Do this job yourself or still instruct a specialist - it's up to you. But remember that if your model of a washing machine has a complex device, it's better not to risk it, otherwise - you can get a more complicated and expensive breakdown than was originally. And it can be fixed only by a qualified master.