How to clean the iron at home?

Everyone has such an excellent invention as an iron on the farm, but whatever brand it is, you need to look after it properly. Modern manufacturers assure that it is not necessary to clean it. But, despite this, you need to know how to clean the iron at home. The reason for this is that there are some factors, such as hard water, synthetic fabric or simply non-compliance with the instructions for use, which lead to unpleasant consequences in the form of scale or carbon deposits. But, fortunately, you can cope with them at home.

to the contents ↑

When should I clean the iron?

The regularity of the procedure depends on how often you use it in principle, and how much you observe the recommended temperature regimes for different tissues. It is advisable, after each completion of the process, to carefully inspect the sole on the subject of tans and immediately remove them.

If this is not done, the following problems can happen:

1. The iron spoils the clothes - it just sticks to the fabric, pulls it and deforms it, melts, which is why it is not always possible to restore the product.
2. The instrument leaves traces from the sole - it can be either black traces of carbon deposits, or rusty stains or droplets due to deposits inside the reservoir.

to the contents ↑

How to clean the iron from the carbon at home?

Even if you had to face such a nuisance, it is not at all necessary to get upset - everything, except for the tarnished things, can be fixed. To do this, take a suitable tool from the ones suggested below and use it to clean the iron at home. Any of them you can remove all traces of dirt from the bottom of the device in a couple of minutes.

Pencil

A special pencil for removing carbon deposits is the safest and most effective tool. In addition, it is quite inexpensive, so it is better to buy it in advance and store it at home until the necessary situation.

Apply it as follows:

1. Take the iron.
2. Preheat to make it hot.
3. Disconnect the appliance from the mains.
4. Scratch a good pencil outsole.
5. Keep this state for a while.
6. Remove residues with a dry cloth.
7. When the appliance has completely cooled down, wipe it with a damp cloth.

Important! During the application of the product, an unpleasant odor may be released, but it does not cause any harm to health.

Hydraulic

To clean the iron from the stump will help such a medium as hydroperite. The principle of its action is as follows:

1. Take a few tablets.
2. Wipe them with the sole.
3. Once the carbon has peeled off, remove it with a damp cloth.
4. Wipe the surface with a dry cloth.

Important! The smell of gas is possible during cleaning. Therefore, with this procedure it is better that there is good ventilation in the room or the simplest option will be cleaning on the street or an open balcony.

Vinegar

Another excellent product that has been successfully used to remove various types of contaminants is vinegar. It will also help in this case, if you use it like this:

1. Take vinegar( you can add a few drops of ammonia to it).
2. Pour it on a napkin or towel as a wafer.
3. Apply vinegar to the appliance switched off.
4. Wait a while.
5. If the product does not work, then heat the iron.
6. Smooth out the wetted napkin.

Important! Do not forget about ventilation, it is very important in this procedure.

Salt

No less cheap and interesting option - salt. But, the only limitation is that it is not suitable for irons that have Teflon coating.

Clean the iron with salt as follows:

1. Take a cotton cloth, spread it on a flat surface.
2. Add a thick layer of salt to it.
3. Pass the heated soles several times over the fabric with salt.

Important! You can apply not one salt, but in combination with candle paraffin. Just remember that when using paraffin, you need to tilt the device so that it does not hit the steam holes.

Soda

Soda is a universal cleaning agent and perfectly suited, including, in order to clean the carbon from the iron at home. It is used as follows:

1. Mix a pinch of soda with a small amount of dishwashing liquid.
2. Apply to the soleplate of the iron.
3. Hold for a while.
4. Good rub.
5. Then wash.
6. Dry with a dry cloth.

Important! Do not allow the liquid to leak into the steam ports.

Peroxide of

1. Soak cotton pad into hydrogen peroxide.
2. Rub the iron.
3. You do not need to wash it.

Important! You can replace the peroxide with a nail polish remover, but only if the coating is not Teflon or sapphire.

Toothpaste

1. Take toothpaste.
2. Apply to the sole.
3. Rinse well base.
4. Wipe dry with a dry cloth until it dries completely.

to the contents ↑

How to clean the iron from the scum at home?

Scale is an equally dangerous problem for the iron, rather than the debris. The cause of scale is often hard water, which we pour to steam the products. If you notice a sediment on the bottom and walls of the tank, or worse - the scum falls on the clothes when heated and processed, you should not immediately throw it away. You can clean the iron from scale with household agents.

Citric acid

To clean the iron with citric acid, follow these instructions:

1. Take hot water - ½ cup.
2. Dissolve in it 2 teaspoons of citric acid.
3. Water in medium cloth.
4. Put in the iron holes.
5. For a few minutes.
6. Clean the fabric.
7. Switch on the appliance and heat it up to the highest temperature by pressing the steam button.
8. Clean the leftovers with cotton buds.

Important! Spray the steam purposefully on an unnecessary cloth, and not into the air or the thing you need to iron. Otherwise, all the dirt will remain on the objects around you.

Vinegar and lemon juice

These products are used according to the method described above, only in this case you expect not only a higher effectiveness of the action, but also an unpleasant smell. Therefore, take care of airing.

to the contents ↑

Useful advices:

1. After purchase, read the operating and maintenance instructions of the device.
2. Use the correct temperature mode for every type of clothing.
3. Do not use metal objects when cleaning the iron - the surface may be damaged.
4. In order for the iron to work, sometimes carry out the prophylaxis against scale in the above ways, even if there are no obvious signs of it.
5. After using the device, wipe it with a damp cloth.

Now you are familiar with all possible ways to remove scale and carbon from the iron. Therefore, any trouble you are not afraid, but still, try not to spoil your assistant, properly take care of him. With this approach, you do not have to wonder soon how to choose an iron or a new thing to replace a spoiled one.