Than to wash off a mounting foam from hands?

Than to wash the mounting foam from your hands?- This issue worries not only amateurs, who first took up repairs, but also experienced masters of their craft. Some people advise that before applying foam with foam, grease your hands with greasy cream or petroleum jelly. In such cases, the foam does not adhere well to the skin of the hands and can easily be removed in case of contact. But surely these people have not tried their own advice in practice, because with slippery, fat hands it is very inconvenient to keep a can of foam and other tools. And grease stains from building materials to withdraw then difficult. Therefore, these recommendations are very doubtful and in case of contact with the sealant on the skin you just need to know what to wash the mounting foam from your hands.

to the contents ↑

What is the mounting foam?

Foam is a sealant that is made of polyurethane. A solution is produced in aerosol packages and is widely used in construction and repair work. Its purpose is filling of cracks and cracks for effective sound, hydro and thermal insulation, fastening of separate parts of building material into a single whole.

There was a mounting foam in the construction industry relatively recently. Instead of foam used to be widely used cement and tow, but the use of these materials took a long time and a lot of work. The appearance of mounting foam greatly simplified such work, because there is no stage of preparation of the necessary substance, and additional tools when working with sealant are not needed at all.

But when frozen, the foam is a solid polyurethane foam. Upon contact with the skin, the sealant adversely affects its cells, since it completely blocks the air flow. This building substance can provoke the appearance of irritation on the skin not only of the hands, but also of the entire body, as well as other manifestations of an allergic reaction. Therefore it is very important to know how to wash the mounting foam from your hands quickly, without causing a harmful epidermis problem.

Important! To significantly reduce the likelihood of mounting foam on the skin of the hands, it is necessary to work with it in personal protective equipment. Dense rubber gloves and work clothes will do just fine.

to the contents ↑

How to wash the mounting foam from your hands, if it has not yet had time to freeze?

The easiest rule to work with foam, which must always be remembered - the sealant must be removed as soon as it has got on the hands or clothes.

Try to remove the dirt with a clean cloth or cloth, gently moving the foam to the center of the stain. The residue should be washed off immediately, until the composition is completely frozen.

Important! When you try to wash off the mounting foam from your hands, be careful not to smear it on the skin.

If this is not possible to remove the foam completely, then use one of the following auxiliaries.

Special aerosol

It is advisable to purchase a special solvent spray before starting work with the mounting foam. The ideal option is the same manufacturer's equipment as the foam cylinder.

Important! A similar solvent is also needed for cleaning guns, with which the sealant was applied. The product is available in the form of an aerosol, which greatly simplifies the process of its application.

In order to clean the mounting foam from your hands, the following simple steps should be taken:

1. Spray the solvent spray onto the contaminated skin area.
2. Rinse thoroughly with plenty of water.

This product perfectly copes with liquid, non-cured mounting foam. But before the frozen substance it is powerless.

Important! Before using a special solvent spray, it is necessary to familiarize yourself with its instruction .

Acetone

From uncombed mass, clean acetone or a nail polish remover with acetone can help. The principle of use is extremely simple:

1. Moisten a rag or cotton pad in acetone and gently remove the mounting foam from your hands.
2. Wash hands thoroughly with soap under running water.

Important! Act quickly and accurately. Acetone has a specific odor, so it is best to clean it outdoors or in a well-ventilated room of the .

Kerosene

This liquid is also effective enough to remove the sealant from the hands. It should be used in a similar way to acetone.

to the contents ↑

How to clean hands of mounting foam at home?

If the above fluids are not found in your home, then you can use the improvised means.

Vegetable oil

This option of cleaning the mounting foam from the hands is absolutely harmless and safe for the skin.

1. Lightly heat the vegetable oil.
2. Dampen the cotton swab into the oil and treat the contamination on the skin.

Important! Surprisingly, this remedy is able to remove even frozen foam. To do this, it is necessary to arm yourself with patience and hold the wetted cotton wool in oil for 20-30 minutes at the contamination site.

Salt

Salt is an abrasive, so it is able to remove the foam and its leftovers:

1. Rub a small amount of salt contaminated with sealant.
2. Wash your hands with soap and water.

Important! It should be handled with salt very carefully so as not to scratch the skin.

to the contents ↑

How to remove the mounting foam from your hands if it is already frozen?

If you do not have time to remove the mounting foam from your hands while it has not yet had time to freeze, the cleaning process will take longer because practically no above-mentioned solvent will not be able to remove the frozen mass.

In this case, the foam can only be cleaned mechanically. For this you will need:

• Rigid brush, pumice or soft sandpaper.
• Fat cream or vegetable oil.
• Soap.

The procedure should be carried out very carefully so as not to damage the upper layer of the epidermis:

1. Spread contaminated areas of the skin with fat cream or vegetable oil. This will soften the hard effect of the brush on the skin.
2. Apply a hard brush or pumice to soap.
3. Gently, slowly, rub brushed foam.

Important! To make the process of removing the foam a little easier, you can pre-steam your hands in hot water for 8-10 minutes .

to the contents ↑

How to clean hands of mounting foam is not recommended?

Some people try different ways of not knowing the right solution to a problem. Subsequently, they either do not receive any result or receive the necessary effect, but cause irreparable harm to the integrity of the epidermis. So, what means to remove the sealant from the skin is not recommended.

Vinegar and other acids

Do not experiment with acids, for example vinegar. The desired effect you will not wait, but to get a serious chemical burn is quite realistic.

Important! This is especially true when you decide not to use ordinary 7-9% vinegar dining rooms, but 70% essence.

Dimexide

Many recommend this medical product as an effective tool for cleaning hands from mounting foam. Indeed, it dissolves the construction foam well, but it is strictly forbidden to treat the skin without the appointment and further control of the doctor.

Important!"Dimexid" is quickly absorbed into the skin and enters the human body. But, like any drug, it has a number of side effects. Therefore, it is better to use them to clean the soiled furniture, floor and walls, but not the skin.

Alkaline agents

Do not use tools with increased alkali concentration to clean such hand contaminations. Traces of the sealant they are not able to remove, but the normal skin acid balance will break quickly.

to the contents ↑

Useful advices:

• If you can not remove the sealant by one of the described methods, then do not despair. Due to the fact that skin cells are constantly updated, the contamination after some time will be cleared.
• After successful removal of contamination, it is advisable to apply a lot of hand cream or aloe juice to soothe and moisturize the skin after an unpleasant procedure.

to the contents ↑

Preparation for work with foam foam:

To prevent the sealant from getting on clothes, furniture, walls, floor and hand skin should be prepared beforehand:

• Always wear gloves and goggles.
• Use work clothes that will not be discarded in the future will be discarded.
• Protect hair from foam. To do this, wear a hat.
• All furniture, floor and walls, which can be dirty during operation, cover with disposable protective material. It can be film or paper.
• Buy special cleansing agents that will quickly remove fresh, occasional foam stains.
• It is advisable to work with a partner, which will help close the through holes, cover the objects near the workplace, put paper under the droplet of sealant.

Observing the simple rules of working with a sealant, you can avoid finding a solution to the problem of how to wash your hands of the mounting foam. But if the trouble has happened, then do not be upset. Use one of the above methods, act quickly and accurately, and the skin will be saved, and there will be no trace of dirt.