50 instructions on how to make flowers from corrugated paper (big and beautiful)

For many who like to do something with their own hands, the beginning of the road to needlework was the creation of various souvenirs from paper. We decided to compile a selection of instructions that will help you learn how to make perfect paper flowers easily and simply. The result will be obvious - even a modest cornflower or daisy made from paper will turn out perfect - and even sweet if you put candies in them.

How to make beautiful flowers from corrugated paper

Crocuses

• Are made in the center stamens. Next, cut out a beige rectangle. It is divided into equal strips, and then cut, but not completely.
• Each of them is twisted. Rolls up into a roll. Mix PVA glue and semolina in small quantities in a small container. The ends are dipped. Waiting for it to dry.
• Take lilac corrugated paper and petals are cut out. To form a natural shape, the ends are slightly curled. We wrap the petals around the stamens. Then the flower attached to a stick and secured with a thread, otherwise it may fall apart.
• The stem is wrapped with a green stripe. Leaves also twist On the sides. After gluing the flower is ready.

Mimosa

• Making flower stalks. To create one branch you will need them 27. Small loops are formed at the ends of the wire pieces. The upper part of the pedicels taped a thin strip of green corrugation.
• After preparing the stems, the next step is making flowers. We take a heat gun in which the glue stick is heated. Apply a small drop of hot glue to the wire loop. After it has completely hardened, the diameter of the flower is increased with a second layer of glue. Now the flower has the desired diameter.
• Apply a thin layer of PVA glue to the frozen drop and lower the workpiece in semolina.
• The first flower was created.

Similar flowers grow on the remaining stems.

Realistic rose buds

• For 1 rose you need 11 petals 6.5x3 cm and 7 more pieces 6x3.5 cm. A bud is formed - a small ball of paper is wrapped in a stretched corrugated circle.
• The stretched and rounded petals are glued one after another so that each next one covered the previous one.

Lilac

To create buds, cut a strip of paper 5 cm wide and cut into small rectangles 7 mm. And to make one flower, take a strip 2 cm wide and cut into the same blanks - 7-8 mm each. But you will need a lot of petals, so it is better to form them each separately.

Tulips

To make tulip petals, you need to cut a strip 4-5 cm wide, cut in half and fold each half in half. To make one flower 3 such blanks are used, twisted in the middle. Form curved boat petals and wrap them around a candy pre-attached to a skewer-stem.

Lavender

• Needed pieces of thin wire onto the stem frames. We twist several wires together to increase the required width. We treat the frames with green tape or a strip of corrugation.
• On a pale lilac background with a piece of paper dimensions 13x20 cm a smooth stretch is created in blue-lilac shades. Use watercolor and a soft, wide, flat brush.
• After the paper has dried, the 1st strip is cut to create small flowers. It is folded in half, then shallow cuts are made along the bend line. Take a toothpick and twist each loop with the tip to give it a teardrop shape.
• The 1st strip of flowers is ready. We form small buds from painted paper.
• Forminginflorescence. The 1st blank of a pale blue hue is attached to the end of the stem. It is wrapped around the top of the stem, from top to bottom.
• Flowers of warm colors are woven from the middle of the inflorescence.
• The 1st inflorescence is ready. Next, the remaining 2 branches are processed.
• A small sepal is cut out of green corrugation and glued to the base of the inflorescences.
• Several green leaves are created. Next, they are given the usual linear shape with a rounded tip. We pull it out with scissors, twist it slightly and glue it to the stems.

Asters

• We make an aster with a bush consisting of several flowers. First, let's create a blossoming aster flower. We use 2 strips of corrugated paper. Their width is 6 cm, length - up to 40 cm.
• Strips are cut transversely to form fringe.
• The fringe strips should have a blunt end.
• We sharpen the ends by cutting at an angle.
• Using scissors, the fringe is pulled out and slightly wraps up.
• We twist the bud with the ends of the fringe inward.
• The bud is glued with hot glue.

How to make a large flower from corrugated paper step by step

1. We draw or print the templates and transfer them to thick cardboard.
   
2. Cut out 15 petals from corrugated paper in the shape hearts and 5 – in the form drops.
   
3. We give the shape to the petals: we stretch the hearts slightly to the sides, we twist the droplets with a pencil.
   
4. We take 2 pieces of thick wire and wrap it with floral tape.
5. A piece of corrugated paper is glued to the stem as a core.
6. A bud is formed: drops are glued, then hearts are glued, and fixed with adhesive tape.
   
7. Cut out the sepals from green corrugated paper.
8. The sepal is secured at the base of the flower with adhesive tape.
   
9. We cut out the leaves and glue them to the stem. Ready!

50 templates and patterns for making paper flowers

Here are templates that you can use to make paper flowers. From the large number of templates offered in the photo, everyone can choose those that suit them best.