How to clean the iron from burnt tissue at home?

Almost every mistress faced the task of cleaning the burnt synthetic material from the iron, because such a problem often arises during the ironing of washed laundry. The cause of burning the fabric may be incorrectly set the temperature of the device, which leads to the formation of an unpleasant plaque on the ironing surface. In this article we will share useful recommendations and tips on how to clean the iron from burnt tissue at home.

to the contents ↑

Kinds of the sole of the iron

In order to understand what it is possible to clean the iron at home from burnt cloth, it is necessary to specify which material the ironing surface of the affected device is made of. In the modern household appliances market, you can find ironing equipment with the following types of soles:

1. Teflon coating is a durable and resistant to mechanical damage coating. Despite its ease of use, cleaning such soles requires the use of special tools and considerable effort.
2. Aluminum ironing surface is prone to the appearance of small scratches and mechanical damages, and therefore quite often burns to the textile surface.
3. Ceramic sole is one of the most popular coatings of the iron, which requires careful care and regular cleaning by means of abrasive-free products.
4. Stainless steel is a rather unpretentious material that is protected from mechanical damage and rust.

to content ↑

Causes of pollution

To understand how to clean the iron from burnt tissue and prevent the occurrence of such a problem in the future, it is necessary to find out and analyze the main causes of such contaminants:

• scale, which can be seen on the bottom of most irons when usingsteam function using tap water;
• prolonged interaction of the heated sole of the device with articles made of artificial fabrics;
• contact the iron with adhesive or containing resinous substances, which when heated begin to adhere to the surface of the sole.

Important! Frequent interaction of the above factors can lead not only to contamination, but also to damage to the ironing surface, and accordingly - substantially reduce its sliding properties.

Strong prohibition of

It is not safe to iron things with a contaminated or defective iron, because such a procedure can forever ruin their appearance. Especially relevant this rule is with the care of white and light things. If the dirt located on the sole of the device, under the influence of high temperature, "solder" to your favorite sweater, then it will be almost impossible to clean it.

to the contents ↑

How can I clean the burnt iron?

You can clean the ironing surface from traces of burnt matter at home using one of the following.

Cleaning Pencil

For sure, every housewife at least once heard about such a special tool for cleaning ironing appliances, like a wax pencil. Buy this tool to clean the iron from burnt clothes, you can almost at any hardware store.

To achieve the best possible result of cleaning procedures, use a pencil according to the following instructions:

1. Preheat the soleplate to the highest possible temperature.
2. Disconnect the equipment from the electrical supply.
3. Put the iron in a well-ventilated room, for example, on a balcony or loggia, carefully handle the surface of the sole.
4. Wait for your appliance to cool completely.
5. Wipe the ironing surface of the appliance with a clean cloth of cotton cloth.

To ensure that the sole of your ironing equipment is perfectly clean and smooth, this procedure can be repeated several times until the result completely satisfies you.

Important! During the cleaning process, you can notice the appearance of a sharp unpleasant odor - this is normal in the chemical reaction of melting a wax pencil.

Vinegar

You can get rid of dirt on the ironing surface with acetic acid.

Important! Molten textile material can get into the holes intended for steam supply, so it is almost impossible to get rid of such dirt mechanically without damaging the device.

The state of the ironing surface can be restored according to the following instructions:

1. Dilute the table vinegar solution with clean water in a 1: 2 ratio.
2. On the ironing board, spread the cotton cloth previously moistened in the prepared solution, which is slightly larger than the working surface in size.
3. Place a slightly heated and disconnected iron on the wet cloth.
4. After a few minutes, wipe the soleplate of the appliance with a clean cloth.

After cleaning according to the above instructions, you can enjoy the ideal cleanliness and attractiveness of the soleplate of your iron.

Citric acid

It will help to clean and quickly clean the ironing surface of the iron using citric acid, which can be purchased at any grocery store. To achieve the desired cleaning result, follow the instructions for using the cleaning compound:

1. Prepare the cleaning solution by adding a teaspoon of citric acid to a glass of purified water.
2. Stir thoroughly the prepared cleaning compound.
3. Fill the water compartment with a liquid approximately halfway.
4. Switch on the appliance in steam mode.
5. Repeatedly alternate 10 seconds of stripping with a 15 second break.
6. After finishing the cleaning procedure, wipe the cold sole of the iron with a damp sponge or a soft cloth.

Nail polish remover

A nail polish remover that does not contain acetone will help you clean the traces of synthetic fabric burned to the ironing surface. To achieve the desired result, follow the following instructions for carrying out the cleaning procedures:

1. Wash the cotton swab with a nail polish remover.
2. Apply a cleaning agent to the soiled surface of a cold iron.
3. The adhering fabric easily leaves the surface of the device.
4. After cleaning, wipe the soleplate of the iron with a soft, damp cloth or sponge.

Paraffin candle

Remove contamination from burnt cloth from the soleplate of the iron with paraffin candle wax.

Important! The effectiveness of this tool is not inferior to special cleaning products, and therefore enjoys great popularity among experienced housewives.

To achieve the desired cleaning results, follow the following procedure:

1. Wrap the ordinary candle in a piece of clean cotton cloth.
2. Heat the iron surface to the maximum temperature.
3. Unplug the iron from the power supply.
4. Place a clean cloth under the iron surface.
5. Wipe the surface of the ironing surface with a pre-prepared paraffin candle.

Important! When cleaning the working surface of the iron, the appliance must be kept at a slant so that the melted paraffin flows over the surface.

1. Treat the cleaned surface with a damp cloth.

Important! If the iron is equipped with a steam-processing function, then use it to remove debris from the holes on the work surface.

to the contents ↑

Useful advices:

1. You can clean the appliance using cotton buds that are wetted in the selected cleaner.
2. After each ironing, thoroughly clean the surface of the iron with an acetic solution.
3. Avoid using cleaning powders and other abrasives that can leave micro-scratching on the sole of the iron, which contributes to the more frequent burning of the fabric.
4. Strong contamination can be removed by scraping the fume with the help of handy wooden objects, for example, a ruler.
5. Delicate fabrics made of synthetic materials are best ironed through wet gauze.

From this article you learned about several effective ways to clean burnt synthetics from iron. Remember about them, so that the next time you are in a similar situation, you were able to act quickly.