Than to grease door hinges that did not creak?

The creaking doors annoy and irritate anyone, and the owners of even the most elite models can face this phenomenon. The reasons that cause the sudden appearance of unnecessary sounds when opening and closing the doors are quite a lot. Therefore, in order to correct the situation, we must first understand what this is happening and then decide what to lubricate the door hinges so as not to creak. You will learn various solutions to this problem from this article.

to the contents ↑

Which doors can squeak?

There is an opinion that modern models of PVC will never creak. But this is not so. Equally often, such problems arise in plastic, and in wooden or metal structures. Everything depends not only on the material in the base, but also on the correctness of the installation, as well as on the intensity of the operation.

to the contents ↑

Why did the doors begin to squeak?

Before you lubricate the loops of interior doors or entrance structures, you need to understand what caused the problem.

The skin creep causing the scraping of the door leafs can be formed for the following reasons:

1. The poor quality fittings were used for installation, which quickly deteriorated. In this situation, you hardly have to puzzle the question, what to lubricate the door. Most likely you just need to replace the broken items.
2. Insufficient amount of lubricant. During installation, new loops have a certain amount of lubricating solution. Over time, it can thicken or spread - depends on the consistency, quality. As a result - there is excessive friction during the movement of the leaflets, the door creaks, you are puzzled by the question of what can be done. In this situation, it is sufficient to choose the optimal type of lubricant, it is correct to apply it - the problem will be solved. It is necessary to do this, as in the absence of the necessary easy movement and sliding, the fittings are quickly exposed to wear, breaks.
3. Rust. This problem is often the fault of metal products, although wooden models can also be installed on iron loops without a protective PVC layer. If corrosion is still at the initial stage, you can simply lubricate the hinges, if the rust has thoroughly damaged the hardware material - it is necessary to replace it.
4. Garbage. Depending on where the door is located, it may be more or less prone to clogging. For example, often in the loops of the entrance or attic doors, dust and abrasive particles can get stuck in the grease. They grind metal, which causes the characteristic creaking of the door.
5. Skew. Tilting of the leaflets may occur due to deformation of the door leaf or due to an incorrectly adjusted position during installation. If the problem is precisely this, it will not be enough to find a tool than to lubricate the door hinges, additional measures will be required to restore the shape and dimensions of the door leaf and door frame.

to the contents ↑

Than to remove the creak?

If you notice that there was a rasping and would like to find an option as soon as possible than to grease the hinges so as not to creak, take the following methods for service. One of these tools can be found right at your fingertips at any time:

1. Used engine oil is an easy way to solve the problem, than to lubricate the door so as not to creak if you have a car.
2. Oil for sewing machines - this option is suitable for needlewomen who have such a technique and they often use it.
3. Conventional vegetable oil - will help to fix the problem, but only for a short while, so you can use it as an emergency measure. Further - all the same it is necessary to apply more effective agent.
4. Pencil lead - this is the simplest thing you can do if the inner door creaks. Place the lead directly on the hinges and several times change the position of the flap so it crumbles and spreads over the hinges, or pre-cut and apply it to the fittings.

If you decide to thoroughly approach the solution of such a problem and act on a long-term result, get out of the house in any building store and buy one of the following tools. Lubricate the door, so as not to creak, you can:

• WD 40 - an effective tool, after processing which solves not only the problem of easy sliding hardware, but also corrosion of metal. WD 40 dissolves rust and forms a protective film on the surface.
• "Litol" - this tool is suitable even if you are looking for, than lubricate the front door, so as not to creak. This lubricant has the property of frost resistance, so it is freely used in open space, even for gate loops and wickets.
• "Solidol" is a rather viscous, oil-based mass. A big plus of this particular tool is that it is very cheap, because of what is popular for processing any metal mechanisms.
• "Tsiatim" - a universal tool, designed not only to eliminate the creaking, but also to protect against corrosion, aggressive chemistry.

to the contents ↑

Useful advices:

1. To make it easier to handle the hinges, first open the door well by opening access to the working surface of the hardware. In addition, you can insert a wedge in the opening to exclude the closure of the leaf and damage to the fingers.
2. If you need to adjust the position of the door leaf, use special adjustment tools for this. Usually they go in a set with the purchased interior door.
3. To enable you to quickly and easily apply the selected lubricant in the right amount, use a syringe or a special grease gun with a nozzle. If these devices are not at hand - take a conventional cotton swab or paint brush of a suitable size.
4. More tools can be applied to the top of the hinges, as it is the workpiece and is more prone to wear.
5. If you notice that the lubricant is spreading through the door, clean the excess with a dry clean cloth or rag.

Now you know all the reasons for the creaking of doors and you can easily solve this problem yourself. We hope you have succeeded and you enjoy the comfort and peace in your home without unpleasant unpleasant sounds.