How do 🔩 slotted screwdriver from the material at hand

click fraud protection

Sometimes when working with different screws or screws hardware across a slotted screwdriver. And if there is none at hand, such products will not work either screw or unscrew. And if slotted screwdriver, unscrew the screws with heads under the cross, then in the opposite direction, this rule does not work. Therefore, in today's article will be discussed on how to from old Phillips screwdriver make a new spline.

It is desirable that in a set of screwdrivers have different shapes and sizes
It is desirable that in a set of screwdrivers have different shapes and sizes

Read article

  • 1 The easiest way to rework
  • 2 Is there any point in remaking a Phillips screwdriver for slotted
  • 3 As slotted screwdriver manufacture from readily available materials
  • 4 Another method for manufacturing a screwdriver
  • 5 Life hacking on manufacturing Phillips screwdriver
  • 6 Summarize

The easiest way to rework

No problems such work does not deliver, if the garage has an electric wizard grinding machine. In this case it is necessary to grind off two opposite faces of a Phillips screwdriver, and then prune the tip perpendicular. Next will only bring a new screwdriver on a fine sandpaper.

It is not always possible to turn the screw a Phillips screwdriver
It is not always possible to turn the screw a Phillips screwdriver

When processing the metal on the grinding machine is necessary to avoid overheating of the tip. For this purpose, a small capacity is placed near the water in which the screwdriver will periodically cool. When overheated the metal becomes black and, as experts say, "falls". This means that it becomes soft. Subsequently, at the slightest load, screwdriver sting will bend, and turn the screw of the same wood such tool is unlikely.

Is there any point in remaking a Phillips screwdriver for slotted

This is probably the main question on the subject raised in today's article. If you think about it, it becomes clear what to make of a Phillips screwdriver slotted easy, but the reverse "transformation" would be impossible. Therefore it is necessary to weigh all the "pros" and "cons", before embarking on such work. Perhaps much more practical to produce a slotted screwdriver from the materials at hand, rather than spoil Phillips, which can be useful at any time.

These screws can be turned both slotted and Phillips screwdriver
These screws can be turned both slotted and Phillips screwdriver

As slotted screwdriver manufacture from readily available materials

Here everything will depend on how tightly twisted the screw or screw. For simple cases, suitable conventional electrode peeled from the wash. Its edge must be put on the steel surface (suitable conventional sledgehammer), then slightly flatten using hammer. After this will only make the desired shape with a file with a screwdriver and bend the opposite direction under the handle for ease of use.

A screwdriver can be made of any metal rod
A screwdriver can be made of any metal rod

In more complicated cases it is possible to use a large nail (the product is perfect, 200 mm length). There is no longer necessary to operate the hammer. Comes in a file grinding machine. The rear part (with a cap) is curved in the shape of the letter "G", to make it easier to work with the tool.

Another method for manufacturing a screwdriver

Often among the masters of the instrument can be found bits screwdriverAs spline and crusades. By themselves, without any special tools, they are unfit for work, but to make them complete screwdriver can. You will need 2 large washers and bolt with a nut for tightening them. Here, everything is easy. Bits of the desired shape is clamped between the washers, which are tightened with a screw nut as tightly as possible. The result is a small, but perfectly functional with a handy screwdriver to rotate the handle.

All that is needed for the manufacture of screwdriver bits
All that is needed for the manufacture of screwdriver bits

Life hacking on manufacturing Phillips screwdriver

As already mentioned, made of a Phillips screwdriver slotted easy, but in the reverse order is no longer working. But there is a way to make a Phillips screwdriver, which is always at hand. To do this, you need to find a key to the corresponding shape of the door lock and modify it a little bit with the help of three-edged file. Thereafter, a small screwdriver, can attach to a keychain. In this case, it will always be at hand.

Key blank from which received an excellent compact Phillips screwdriver
Key blank from which received an excellent compact Phillips screwdriver

Summarize

It is clear that, in a pinch, you can always find a way out, having made a particular tool independently. We just need to understand that self-made screwdriver will not possess the qualities that are inherent in the factory tool. Therefore it is better if the pantry is all the necessary tools for all occasions. Then you will not have to spend time vytachivanie or remaking a screwdriver in the other.

Craftsmen gather with their hands even elektrootvortkiWe hope that today's article will help small handyman in a difficult situation. Related boldly ask them in the comments below if you have questions. Editorial HouseChief will try to answer them more fully and quickly as possible. There you can share your experiences, and in the production or alteration of screwdrivers for the necessary parameters.

And finally, we offer you a short video, which will complete the article: