Many after buying a washing machine trusted by its connection to the master. However, it is easy to do yourself, knowing procedures. Start the installation of the washing machine in the apartment with a plan and unpacking.
- water supply,
- to the sewer network,
- to electricity.
For installation you need a room with communications. Sometimes to connect the washing machine is needed redevelopment.
Comfortable conditions for the installation:
- closely spaced mains and sewerage pipe systems;
- Smooth surface;
- Access to use.
Set the machine may be in the bathroom, toilet or kitchen. Resourceful craftsmen put stiralku over the toilet on a solid shelf. In the bathroom, it can be installed near a sink or under it.
If you put on top of the countertop, will expand the functionality of the room and the equipment will be safe from falling into the water on the hull. The machine can also slide under the sink, place between the edge of the bath and the wall.
Install the washing machine in the bathroom or combination bathroom can lead to rusting due to moisture.
Preparing to Install
Before you install the washing machine, unpack it and remove the transit bolts. Read instructions and circuitry, read the back wall of the device. Remove the bolts ordinary screwdriver.
Insert plugs into the empty holes to protect the drum from a quick breakdown.
connection
The water pressure must be 1 atm, the water purity is required.
Low pressure can be increased and filters buy cleaning water.
The washing machine is normally connected to the cold water, which is heated by heating elements according to a predetermined regime or temperature.
By sewage
The yield in the bathroom or toilet is organized via hose-hook. The length of the hose should be above the level of the lower machine 60-70 cm.
Siphon organizes stationary draining. It has outlet for machines over the siphon knee. Connecting appliances directly to the sewer, there is an unpleasant smell of stagnant water and soap.
Sewer pipe diameter should be 4-5 cm. It can be installed directly via outlet seals and the drain hose with the letter S. The hose must not touch the drain water. Outer point should be above the floor of 50-70 cm.
water supply
Ways to connect the machine to the water supply:
- using a clutch;
- cutting in the metal-base;
- via a tee;
- indirectly.
Box via couplings suitable for plastic and metal pipes:
- Embed the valve in the water supply due to the crimp sleeve.
- Two halves set on the pipe and tighten it with screws.
- Through wearing sleeve cut a hole.
- Prepare the hose for three quarters of an inch.
- One end connect to the technique and the other to the valve.
The tapping of the metal-base is suitable for pipes made of metal:
- Prepare a special fitting in the hole made in the pipe insert the tee.
- Attach to the tee ball valve and seal sleeves of rubber.
Connecting equipment with a tee, activated hose. Before washing, mixing hose every time you need to deploy, so this method of backup or temporary.
Installation with no running water in the relevant room with unforeseen plumbing. For example, in the country. To solve the problem of lift equipment 1 m and connect the large water tank to the machine with a hose. You can also buy a pump station.
For mains
The last stage of connection - summing up the power. Proper conduct of the work will eliminate most of the problems in use. It is not superfluous to recall that high voltage in combination with water is life-threatening.
Ground switchboard via bus 3 mm. To connect, use a 3-wire outlet. In the kitchen, the machine can be used with a hob one outlet. Extension cords should not be ground contacts. The device should be energized by a separate wire of the counter. The wire can replace a portable device tripping.
Check the operation after connecting
Reviewing all connections and connection instructions, try turning on the machine. If all is done correctly, the device will start:
- Set the temperature control to 90 °.
- Fill the water tank, fix the time and checking the instructions.
- In case of leaks drain and repair the defect. If leaks not, in 5-7 minutes to warm up the water in the drum.
- Finally, check the quality of spinning and draining.
In the process, there should be no extraneous sounds. Almost all devices work quietly. Rattle will indicate failure.
helpful hints
Do not connect the ground connections to the heating batteries, gas and vodomagistralyam.
To block the flow, use linen or paste.
Place the body correctly, install the legs straight. This will prolong the period of technology and eliminate congestion. The drum will be placed without tilting, rotating smoothly without shaky.
Horizontal deflection should not exceed 2 °. To optimize the placement, use the adjustment feet.
Concrete floor provides cushioning protection.
Not to report under the legs of linoleum and rubber materials. Such substrates have a negative impact on the centrifuge.
Do not discard the shipping bolts, they can be useful in moving.
Check the drain installation, the hose is not dropped out of the tub and the water is not flooded the bottom neighbors.
The machine can be operated without central water supply by connecting it to the tank with water, placed vertically in the 4 m above technique. Thus 1m gives 0.1 atm. C 0.4 atm. Equipment can be operated without a pump station. Correctly set the washing machine really their own. The process does not take a lot of time and effort to save money on the master services.
