Why does not spin in the washing machine

• residual water in the drum after opening the lid;
• draining dirty water, followed by a high noise;
• sustained release of water from the drum;
• systematic failures in the spin starts.

When the manifestation of such symptoms should immediately understand the damage. Do not tighten with the repair so as not to provoke a more serious breakdown and cash costs.

Causes of poor extraction

Some of the reasons for which no press machine the automatic actually fix itself. In more complex cases, contact the person.

In the presence of guarantees do not attempt to carry out repairs. Even if the warranty period has expired, the lack of experience in the repair of household appliances may aggravate the situation.

The reasons why the washing machine does not spin:

• Improperly selected wash program.
• Before troubleshooting, make sure that the spin is enabled. Some programs do not provide wash mode. These include the delicate wash program. To solve the problem enough to understand the management with the help of the instructions.
• Overloading of the machine a lot of clothes.
• The reason for the termination of the work immediately after the washing cycle can be crowded drum. The problem is common in narrow machines. To eliminate, remove loose items from the machine and re-spun. Do not load items that exceed the prescribed weight of the device.

The uneven distribution of the laundry in the drum

When the laundry after washing is unevenly distributed in the drum at high speed spin imbalance occurs and the machine completes the process work. To fix the problem, Spread evenly things and restart the spin cycle.

drain pump

Dirty water together with exhaust cleaners forcibly output from the device using the water pump. Its failure leads to the fact that no liquid comes out of the machine and the laundry can not be overcome. Breakage pump is sometimes associated with failure of the motor.

Most often this occurs because of the clogging of the pump impeller. It will be much buzz, but will not be able to pump the fluid. Cause poor draining waste liquid can still be clogged filter or nozzle.

To diagnose the breakdown:

1. Restart the drain program. Perhaps the failure occurred.
2. If after you restart the change has occurred, open the drain manhole cover in the lower part of the front wall of the machine.
3. Remove the filter and inspect for contamination.
4. Start the device in spinning mode.

Look into the drain pump impeller. If it rotates, the clogged drain pipe, and if not, then the pump is out of order. When the pump failure replace new part.

So as not to flood the room, put a drain hatch container for liquid gathering.

The water level sensor

For optimum performance, washing machine in her fitted for Control Module sensors. Pressure switch functions as a water level sensor in the drum. With the help of the control module is no signal the presence of liquid. The machine can not make the water drain and begins to spin the laundry.

The machine switches off at the end of the wash program, without having to drain the water and without opening the door. Drain the liquid from the machine through the discharge hatch.

Breakage pressostat may be associated with clogging. In this case clean it. To get to the pressure switch, remove the top cover stiralki.

Usually it is installed in the upper portion of the rear wall. If the pressure switch did not work after the removal of dirt, replace it.

electronic module

If the spin does not work, it may indicate a malfunction of the electronic module in the washing machine. It stiralki brain, so it is non-functional partial impact on the entire device.

Signs of damage to the module:

• Spin laundry mode is activated every time;
• machine does not reset the speed and crashes;
• running program discarded by themselves;
• the device is not working properly.

In some cases it is necessary to flash the module or replace components. In all other cases it is necessary, replace the control board.

electric motor

Automatic machine can not spin the clothes in case of failure of the motor. The drum can rotate without having to dial the required number of revolutions or not rotate at all.

To solve the problem, remove the engine and rang each of its windings multimeter. If winding is OK, inspect brushes and tacho. If there is a damaged coil, replace the motor.

tacho

The engine of every car is equipped with automatic tachometer. It allows the control module to control the speed dialed engine. A sign of the sensor failure can be that the drum is not gaining momentum.

To solve the problem:

1. Disconnect the device from the power supply to avoid electrical shock.
2. Remove the back cover.
3. Disconnect the cable from the motor.
4. Disconnect engine mounts and pull outward.
5. Find the tachometer in the back of the engine.
6. Remove the old sensor and install a working part.

Before repairs fix all the components to be dismantled by means of a photo or recording a video to remember the sequence of assembly.

Worn brush motor

The engine can not operate at full capacity due to brush wear. They are manufactured on the basis of graphite and eventually erased cease supplying power to the motor rotor.

To replace:

1. Remove the engine from the washing machine.
2. Remove the brush attachment screws on both sides of the engine.
3. Replace worn parts with new ones.
4. Replace brushes with visible damage work surface.

Violation of PETN

The machine stops to spin the clothes because of irregularities in the work of the heating element. Heating element in the device is needed to maintain a particular temperature of water at different modes. At failures in the work of the electronic module may stop the wash, rinse or spin.

Self-diagnose only external damage PETN. If it has chipped or cracked, it needs to be replaced. For complete diagnostics, refer to a specialist.

Spin in the car stopped working

If stiralka ceased to spin the clothes:

1. Refer to the instruction, whether the machine is in the prescribed program to squeeze out the laundry.
2. Restart the device or turn separately spin cycle.

If the spin does not turn on after these actions, check the items in the tub. At a crowded machine, remove the excess amount of laundry. If a lot of things got lost in one lump, evenly spread out them and start squeezing.

If these suggestions do not solve the problem, perform diagnostics. Having experience in the repair of household appliances, try to diagnose and correct the problem on their own.

Prevention of breakdowns

Failures generally occur due to improper use. To reduce the risk of malfunction, follow preventative tips:

1. Install and connect the machine in strict accordance with the instructions.
2. To protect the device from surges connect it to the mains through the stabilizer.
3. Do not expose the drum foreign objects. Things coated decor load in the car only in a special bag.
4. Do not exceed the permissible weight of the laundry to boot.
5. After each wash, clean the tray of detergent from the detergent residues.
6. Wipe the rubber seal of the door.
7. Do not keep the door closed after washing to not formed the fungus.

Some causes of malfunctions in the spinning machine can easily correct yourself. By following the simple rules while using the washing machine, it reduces the risk of breakdowns and extended product life.