Washing machines are sophisticated household appliances, which requires compliance with the rules of use and maintenance. Faults in the electrical or scum may damage the appliance. In addition to the washing cycle the display you can see strange error codes. Consider the possible reasons for the error is displayed on the Samsung LE washing machine.
What means the error code LE
Any error readily identified with the instructions. Decryption error codes and their possible causes can also be found on the Internet.
If the washing machine outputs a mark Samsung LE error, then during washing decreased water level in the drum or water is discharged therefrom.
Triggers automatic disconnection of the art to prevent heating and electric heating element. We have to stop the cleaning process, pull out the laundry load and look for the problem.
When heated PETN without water in the tank can cause a fire!
In similar cases, the washing machine Samsung may provide E9 error, LC, LE1. It depends on the year of manufacture. Different models give different values for the same problem. Also the diversion of water related error 5D.
If stiralki no built-in display panel lights come on all modes of washing and two extreme temperature indicator.
Causes of LE
To correct the problem, you need to understand the primary source of error. By using code, you can self-diagnose the problem. Samsung Washing machine gives an error LE:
- machine drain hose is too low;
- hose is not connected to sewage systems;
- in a tank or housing a crack, from which the water flows;
- slightly open drain filter;
- leakage associated with the air tube, in this case the machine is stopped before the spin cycle;
- broke water level sensor;
- defective display.
Do not use detergent that is not designed for automatic washing machines. Apart from the risk to spoil the delicate things can be in addition to break the device. Also not exceed the amount of the mixture.
In the event of failure the display will show 5D code that would mean water leakage with soap suds. Pena eventually come and wash itself will continue, but at a regular flow may occur more serious problems.
Eliminating LE
Once the machine produces any error, unplug the appliance. Then perform a number of actions:
- Check the location of the drain hose. It should go up first, and after fixing down.
- Inspect the hose for cracks, punctures, fractures. If the hose is leaking, replace it.
- Make a tight closing of the drain filter cover and the absence of a leak.
- Disconnect the drain hose from the sewer pipe and lower in the bath or basin.
- Turn the machine on the wash mode, in which the error appeared.
If the error persists, then the problem is in the wrong hose connection to the sewer drain. To fix this, re-connect the unit to a drain, using the instructions or using a wizard.
If the error continues to flash, her face more serious damage. Check the drum surface and the machine body for cracks. Through them the water can flow. Take the device in for repair, as simple gluing gap does not help, you need to completely change the housing or drum.
In addition, the problem may be related to the TEN-ohm. At the heater can deviate mount. Because of this machine is paused, and outputs an error. Try to replace the self-fastening, carefully dismantling the machine through the back wall of the housing.
Other possible causes are listed in the table below.
| failure | Cause | How to fix |
|---|---|---|
| It displays an error, and a machine formed a puddle | Damaged seals or drain hose | Seal or replace the parts with new |
| Display an error at start | Faulty water level sensor or a clogged formed pressostat | Clear the blockage; otherwise replace the sensor |
| Error eliminated in the rinse or spin mode | Faulty electronics machines | Adjust the normal machine operation using a soldering board or replace the power supply |
| Water flows from the rear wall of the machine when an error code on the display | Leaking hose | Replace the part with a new |
| Error code blinks continuously | wiring | Repair or replacement of wiring, reconnect the machine |
If the new stiralki first LE error code appears, try turning off the machine and wait. Failure may occur in the control module and reboot often solves the problem.
Repair of cars of many details, especially electricians, requires a professional approach. In no case do not climb inside the unit, if not carried out replacement of parts to it. In addition, it will exacerbate the problem, it is not safe to live.
If you notice a spontaneous discharge of water from the washing machine, unplug it from the mains as soon as possible and begin to look for the cause. A similar phenomenon is dangerous for life: water can get into the power outlet to shut off or leak to neighbors below. If a serious breakdown, refer to the repairman.
