Washing machine does not drain: the underlying causes and repair

It is suspected fault on any grounds:

• Slow draining, can be accompanied by dysfunction of the program.
• Interrupting a program on water draining stage.
• Water does not flow at all.
• Some of the wash program the water is drained, the other - no.
• After the main wash water is discharged, and after rinsing - no.
• Spin mode takes place immediately after the blocking of the water drainage.

Experts identify 6 main reasons for failure:

• clogging debris accumulation connecting the lads - the area between the pump and the tank;
• getting into the pump outside things;
• pump filter clogging debris - pump;
• malfunction of the pump;
• clogged sewer or siphon;
• clogging the water drainage hose.

Independently drain

Before starting the repair, the water from the machine you want to delete. If the automatic drain does not work, you need to pump manually.

Drain the water out of the car one way:

• Substitute under a door on the bottom tray and remove the filter. For a complete draining of fluid, car body tilt in the direction of the filter. Should run out all the water, which is in the tank.
• If the drain through the filter is not obtained, its drain through a branch pipe. It needs to be pre-cleaned. nozzle cleaning is sometimes enough to restore the outflow of water.
• If the first two methods do not work, the water drain hose. One end of the dip tank, and the second into an empty container. Draining takes place according to the principle of communicating vessels.

Trouble-shooting

Check the drain hose

The reason that the washing machine does not drain may be cross-clamping, twisting or improper installation of the drain hose. Begin to search for the causes of this problem. Inspect the condition of the hose all over, straighten found kinks and twists. At the same time explore the hose for cross-compliance and on the location of inflection requirements. It should be at a sufficient height. The minimum recommended value pipe - 0.6 m from the lower edge stiralki.

Clogged siphon

When organizing discharge directly into the sewer, the problem could be a clogged garbage trap. The drain hose is removed from the adapter and drop in the bathroom or empty containers. If you then earn drain, you have to clean the drain. After cleaning, the water should go well.

clogged filter

Making sure that the machine does not empty not because of the drain hose, proceed to search for the causes inside the body. Begin with the drain pump filter survey. Flat screwdriver to remove the cover. Filter for most models is located under the tank on the front panel. Remove the filter and clean the mesh, if it is necessary.

Next to the filter is a drain tube. Through it, the water is drained from the tank. To avoid the formation of puddles of water on the floor, prepare in advance containers and rags. The filter can accumulate: wool, hair, buttons, coins and small things, which broke away from the clothes. Most models have a filter to unscrew the handle. He gets out of the tight seal of the rubber gasket.

Pollution even more complicated twisting of the filter. The cheapest models of the filter can be omitted.

All these defects are removed easily by yourself. The restart of the program, straightening the drain channel and filter cleaning is no big deal. Preventive cleaning of the filter is recommended every 5 years, even without any signs of blockage and failure of the machine. If the hose and filter found defects, are moving deeper - in the direction of pipe between the pump and tank cars.

jammed impeller

The filter is located an impeller pump. When removing the filter, it is clearly visible within the orifice. If you try to roll out, its blades rotate with difficulty, or not rotate at all, you need to remove the object that is blocking them. If a foreign object is not detected, and the impeller does not rotate during the spin cycle, it is likely that the problem is in the pump.

Faulty drainage pump

To check the status of the pump, it is necessary to remove the filter and turn on the spin cycle. Flashing his torch, learn how it works. If the pump is stationary it needs to be replaced. New pump replace the old one. To do this, remove the spout assembly, unfasten it from the pump and remove the wire. Install the new pump, attach the wire in place and restore the integrity of the machine.

Smash the electronic module

This problem is usually characterized by low-cost technology. Expensive models are equipped with a function of blocking the drain pump in identifying what is not working in the washing machine drain. In the absence of this feature, the pump signal is applied as long as the machine will not burn. It is possible that in this way manufacturers increase sales.

Bearing out of order

If currentless machine during manual rotation of the drum sounds heard or felt extraneous rotation resistance - the problem of the bearing. Own the problem persists, call the wizard. Change the victim bearing a new or repair old - can only be a specialist.

Broke water level sensor

If the damage of the sensor, the machine can not determine the amount of water remaining at the time of shutdown of the program. Before you take steps to repair the sensor, make sure it is damaged. The probe is positioned at the top of the side wall. To dismantle the sensor are loosened two screws and remove the back cover. Further spun two bolts which fix the sensor itself disconnect hoses and suitable contacts. After removing the probe for examining the integrity and purity of the tubes. Identified damage and contamination is removed.

If the cause of your pump, as it is replaced

Faulty pump - one of the most serious injuries, leading to disruption of the water drain. The machine, in addition to failure to drain the water is still buzzing. The pump is likely to have to change.

pump replacement algorithm:

1. Remove the drain node.
2. From flush assembly disconnect the pump.
3. Disconnect the appropriate wires to it.
4. Old pump is replaced.
5. Putting it in reverse order.
6. To pump connected wire.
7. Drain assembly to its place.
8. Connect the machine to the network and run the verification laundry.

If after all the action, washing machine drains poorly, you need to apply to the repair company.

Prevention of faults

To extend the life of trouble-free service life of the machine, it is recommended to follow the simple advice.

The instructions for each machine manufacturer specifies the recommended weight of the laundry on one tab. With regular reloading, the machine works on the wear, which increases the chance of breakage.

Before loading the laundry be sure to check the pockets. Once inside the clips, coins, pins and headphones damaged pump impeller motor.

To connect the machine to the network use a surge protector. It smooths large power surges. If it is not applied, the electronic unit can be damaged.

Filter under the hatch on the front of the machine needs to be cleaned regularly. It is recommended to carry out an audit of the filter every 6-12 months. The filter may be a cause of disorders of draining water.

In the preparation stage of washing carefully expose the required mode.

Time to carry out routine cleaning machines a year. This is accomplished by the addition of detergent and liquid descaling. Expose Mode maximum temperature and the washing is carried out without washing. This method allows you to remove scum and dirt.

If you follow these tips, the device will be a long and trouble-free operation.

We have considered the main causes of failure of the washing machine to drain the water. If stiralka does not drain, not necessarily immediately contact the webmaster. Poveda diagnosis and if the failure is not complicated, correct. If the problem is serious, better not to experiment, and consult a workshop.