Coded symbols on the display of the washing machine Electrolux report problems in its work. After examining washing machines Electrolux error codes, you can quickly locate the failed node or breakage.
During the wash water supply fails. It is absent or has not had time to gain. Possible reasons:
- the solenoid valve is not working and no water flows;
- no signal is received to open the valve;
- no pressure and the water is dialed slowly;
- clogged pipe systems.
To correct the problem, do not necessarily have the experience or lots of tools:
- Reboot the system. Reclosing equipment starts a normal washing process.
- Wait until the water pressure becomes normal. If the car has not had time to draw water for the allotted amount of time, the processor also will give an error.
- VIEW and water supply tubes. They may be clogged. Plaque on tubes eventually forms scum which interferes with the normal set of water.
- Spend diangostiku conductive wires valve for rupture. The vibrating effect when the machine breaks contact terminals.
- Prozvoniv spool valves, check resistance.
- If the steps do not help to resume the operation of the device, replace the control unit.
E10 error is also common in the Electrolux washing machine. It is consonant with the E11, and has the same meaning.
E13: there was a leak, liquid enters the machine pallet
E13 Error in the Electrolux washing machine is displayed when water leaks into the tray., Look for a crack in the hull to ensure fault. The problem appears after prolonged use of the device. Often burst pipes and cuffs.
The machines may occur circuiting wires that go to the leakage sensor. It is located next to the tray stiralki. In the middle of the pallet there is a connector for fluid flow. It is a sensor. When the container is filled with water, the float closes the sensor circuit. For repairs need help wizard.
E21: problem with water draining
A code error is displayed if during 10 minutes water is merged from the drum. Clean the filter, pipes and hoses. Check pump coil resistance, it should be about 200 ohms. Another reason may be damage to the electronics module defect.
Error E20 in the washing machine Electrolux also speaks about the problems in the drainage system. Other possible designation of faults in the drain system: EF0, EFO.
E23: triac broken
The car burned triac, which is located on the electronic board. It is responsible for your pump. To fix the unit, test the control module and replace it with a new triac.
E24: problem between pump and triacs
If you still have problems with the draining water, look at the contacts between the triacs and fanfare. The cause of failure can be faulty wiring. Spend wiring diagnose, isolate the damaged parts or completely replace the loop.
E31: problem with the level switch
If the relay is broken, there are problems with the water level display in the car. Replace the old to the new level sensor. Before replacing the slide wiring diagnostics.
E32: failure of the pressure switch
If the pressure switch is faulty, an error E30, E32. Replace it with a new one and repair the wiring, which combines detail with a control module.
It gives an error in the following cases:
- not translated water supply valve to an open position;
- weak pressure;
- a complete lack of water in the system;
- filler clogged filter;
- burst tube relay.
Regularly clean the filter and replace the tube if necessary.
E33: incorrect operation of the protection sensors
Damaged or broken tube sensors pressostat. Test the device, check the voltage in the socket using an ohmmeter.
E34: problem with the level of antikipeniya and pressure switch
In the case of E34 errors, check the pressure sensor and electrical circuit. Replace the pressure switch tube.
E35: the rate of water in the drum exceeded
As a result, excessively filled liquid tank there are problems with pressure switch. Check the device and install the defective item.
E36: Fault relay and the electric heating element
If failure came relay, check the sensor operation. If necessary, replace the part.
E36: Fault relay and the electric heating element
Check the operation of the element. If necessary, install a new one.
E37: breakage sensor 1st water level
Error indicates sensor failure. Inspect the device, troubleshoot and replace the element.
E38: No Signal from pressorata
If there is no signal about the change of pressure, then huddled tube relay. Clean or replace the tube member.
E39: Fault overflow
Check the pressure switch overflow. If necessary, replace the part.
E3A: TEN-fault relay and
If the device has given this error, replace the relay or heater.
E41: door is not closed
E40 error, E41 say that the door is locked not to the end.
E42: device failure, the door locking
UBL requires inspection and replacement of the lock.
E43: problem with triac control board
Triac board is responsible for UBL. If it broke, troubleshoot board and replace the element.
E44: problem with the door closing sensor
If you broke the door closure sensor, it must be completely replaced.
E45: Fault UBL wiring
When the contacts are faulty wiring between the module and UBL, and repair the lock circuit.
E51: problem with the motor triac
E51 error occurs when a short-circuit. Triac motor burn out and in need of repair or complete replacement.
E52: the absence of contact and the block tachogenerator
This error occurs when the breakaway washer attachment. The coil is displaced and lost data supply controller. Return the spool to its original position or change tachosensor.
E53: the broken section of the triac control circuit of the drive motor
Check and replace the Triac or its parts.
E54: sticking contacts of the 1st relay of the motor reverses
In case of violation of contacts or relays required repairs or complete replacement of the elements.
E55: problem with the motor wiring
If there were problems with the wiring, it will require a thorough repair.
E56: No tacho signal
The error is displayed when the signal from the tacho is not received for more than 15 minutes. Start pinging the device and replace the part.
E57: It is permissible to exceed the amperage
Amperage value quoted above 15A. Requires verification of the drive motor and feed chains.
E58: the current in the drive motor above 4.5 A
When issued, this error is necessary to diagnose the drive motor and the supply voltage, check the control unit.
E59: no tachometer signal
After issuing the command to the engine, there is no signal from the tachometer. Check the wires, replace the tachometer and an electric motor. In special cases, require the complete replacement of the electronics module.
E5A: overheating of the cooling radiator
If the cooling radiator is heated over 85 degrees, it is necessary to replace the electronics unit.
E5V: The problem with stress
If the voltage has dropped to 175 V, check the wiring and replace the electronic unit.
E5S: high voltage bus
If the voltage of the line more than 420, immediately replace the electronics unit.
E5D / E5E / E5F: problem with FCV
It needs a complete change of the electronics unit.
E61: the water is not heated
If the water is not heated to the required temperature in the allotted time, make sure of serviceability of PETN, his contacts and drives.
E62 / E66: faulty heating relay
Check the wiring, circuits and relays. Test the sensor multimeter - resistance should not be more than 6 ohms. If the sensor is faulty, replace it with a new one.
E71 / e74: voltage temperature sensor
When error E70, E71, check the correct location of the temperature sensor on the continuity of contacts. Make sure that the device is not shorted.
E82 / E83: problem with selector
Rate element is positioned correctly. Spend wiring diagnostics. If the wrong configuration, the item must be replaced.
E84 / E85: defective recirculation pump
Replace the pump or electronics.
E91 / E92 / E93 / E94 / E95: problem with the configuration
At E90-E95 error requires replacement of the electronics unit.
E9A: Infraction
The problem of working electronics and speaker. Replace the unit.
EA1-EA6: problem with DPS
Check the wiring, replace the main unit or the engine drive belt.
EB1-EB3: a problem with the voltage and frequency
Check the mains voltage, and its parameters.
EBE / EBF: the failure of the protection circuit
Problems with the relay protection circuit or recognition. Diagnose and replace the electronic module.
EC1: defective inlet valve
You must install the new item.
EC2: failure of the turbidity sensor
Required inspection and replacement of the gauge.
EF1-EF5: problems with drainage
It is necessary to explore the drain hose and the filter, sufficient to adjust the pressure and flow of water. Monitor the amount of laundry in the drum and washing quality. You may need to make the replacement of the cable or the pump.
EH0-EN3: a voltage problem
EHO-EH3 error signal a problem with the network. Evaluate network for interference frequency. Replace the electronic unit, mains.
EHE: The problem with the protective relay circuit
Check and reset the electronic module.
EHF: a problem with indexing circuit protection
Electronics need replacing.
Fully washable with the machine Electrolux simple. It is important to know about the common system errors that may occur. To the device will last for many years, timely diagnosis and do not delay repair.
