Much more often the reason that from the camera unit smells bad, is the accumulation of dirt and fat in different parts of the dishwasher. Particles of food can get stuck in those areas where they are not washed out with water and give off unpleasant odors. These places can be:
- drain filter mesh;
- drain hose;
- hard to reach areas under the door;
- lattice.
If you feel that the smell of mold machine, it may be due to the fact that the inner surface of the accumulated moisture that caused the bacterial growth. The camera apparatus after washing should be dry and clean, only then it can be closed. Residual water may be not only on the bottom of the device, but in the rubber seals of the door, which causes an unpleasant smell and deterioration of parts of the device.
When the water drain hose is not connected to the sewer, the user may feel that sewage smells. You need to check out the instructions to the dishwasher, if you do it correctly. In order that water does not stagnate in the hose, it must be not less than 40 cm above the tube.
Sometimes the heating elements or wiring may burn in the dishwasher. Then, there is a peculiar smell of melted wires. In this case, it is necessary to contact the service center for repair.
cleaning machines
If you have checked and found out that the cause of unpleasant odors are pollution, it is necessary to clean and wash all the problem of the unit. It should be noted that not all household cleaning agents suitable for cleaning the dishwasher. This process can not be used:
- preparations containing chlorine;
- detergents;
- any abrasives.
They can damage the plastic and metal parts of the device. When wash chamber using mild detergents, and also warm water.
First you need to clean the mesh filter drain. This is the main problem areas in any dishwasher. As a rule, food particles accumulate in this place. To clean the filter, it is necessary to remove the metal element, finding the camera and remove the bottom of the filter (see instructions how to do this).
Wash the filter elements under hot running water. If it stuck food particles, remove them. Wipe dry with a cloth piece and replace.
Very often on the inside surface of the door accumulate deposits of grease or other contaminants. They can be between the rubber seal at the bottom of the door, as well as in the joints. Rinse thoroughly with warm water with dissolved in it with detergent all areas.
If you see a big fat accumulation, wash the area several times, till they completely disappear. Good, clean the door seal, it often collects moisture and contamination. Wipe all parts with a dry cloth.
Thoroughly rinse the grille, side walls and a bottom chamber. After washing wait for complete drying of the surface only after that the door can close tightly.
Check to see if there are folds in the hose to drain water. Referring to the instructions, remove it and see if there are any blockages in it. In the presence of contaminants, clean it and wash in warm water.
How to fix
After cleaning the machine, you can take steps to eliminate odors if they are still present. To do this, you can use:
- household products;
- vinegar;
- baking soda.
In stores you can purchase a variety of means to remove lime deposits and traces of fat in the dish washing machines. Dilute the drug according to the instructions and process them to the camera. Thereafter, wash with clear water and dry.
If you do not want to use chemical compositions, you can use folk remedies. An excellent way to freshen the inner surface is the use of vinegar. It not only removes an unpleasant smell in the dishwasher, but also disinfects the surface.
It is necessary to pour a small amount of water diluted with vinegar in any container and leave at the bottom of the chamber. After that, run the machine on a standard program. After the process, leave the door open, to erode the aroma of vinegar, because it's pretty intense.
If you can not stand the smell of vinegar, use an ordinary baking soda. soda powder absorbs odors, besides, it is absolutely harmless. A small amount (approximately half a glass) the bottom pour apparatus. Then, enable short mode (quick wash). After the wash cycle, wipe and dry the machine chamber.
In order to avoid a long and difficult process of cleaning apparatus, timely care of your equipment. It is necessary to regularly clean up the contamination in problem areas the device and do not leave moisture on the door and inside the chamber.
Preventive measures are described in a sufficiently broad and important topic fully disclosed. From myself I will add is that you can use this tool here Odargan, quite decent tool in the prevention of a good helper.
