How to adjust the plastic balcony door video and tips

Many owners of plastic doors from time to time faced with such a problem: how to handle plastic balcony door. In this design can not close properly, pen or bumped loop. The process of regulating the lid unit is different complexity. You can tweak and improve hardware in a few minutes.

Design features balcony door

PVC products are fit for everything loggia or balcony. Similar designs are characterized by resistance to the influence of thermal fluctuations and humidity. These products are lightweight and do not become a burden to moisture and temperature changes. When creating plastic doors apply the same profile as in the installation window.

Plastic products have certain advantages:

• thanks to the multi-chamber profile perfectly retain heat and have good sound insulation;
• characterized immunity to all manifestations of the external environment;
• have the environmental friendliness and durability;
• characterized by the ruggedness of care.

Most often used for the construction of balcony glass top and plastic bottom. In the presence of a strong door frame is performed with the use of triple glazing. It allows you to create stained glass design and improve the natural indoor lighting.

The following options are popular designs:

• Sliding models that are moved by a system of grooves. With their installation is required to comply with the tightness. Also, the installation is carried out on insulated balcony;

• doors with one or two doors, which are equipped with a hinged locking fittings. This requires adjustment of the hinges;

• double design with impost. In this model the doors open, but between them is placed insert - impost;
• leaved embodiment consists of two parts. In this case, one is fixed in one place.

Of great importance is hardware. It allows you to clamp tighter. Hardware is divided into internal and external. The internal elements are no different from window designs. The inner door includes knobs, balcony latch laths and stationary handle.

Helpful information! The most important stage - the installation of the door frame. It is set with a precise definition of the vertical and horizontal directions. Then the construction is fixed by means of screws and anchor bolts.

How to adjust the plastic balcony door ways

Most owners of the balconies are concerned about how to adjust the plastic balcony door. You can tune the device on its own, allowing you to:

• apply controls to retract the slack canvases;
• remove changes in any direction;
• configure pressing;
• Place under the handle plate to air regulator;
• perform lubrication of all moving parts.

The grease used is a special composition of the oil, and will need a brush or cotton swab.

The following table shows some of the equipment configuration of doors:

Picture	Methods of adjustment
	Adjusting the loop.
	Setting pins position.
	Methods adjustment using hex key
	pressure adjustment seal.
	Features of setting end of the balcony unit
	Setting clamp.
	Scheme adjust the upper and lower hinges.

Related article:

Adjustment of plastic doors and windows yourself. This task really cope without resorting to a specialist. All you need to know about the features of these regulatory structures, we have gathered in this material.

The main problems of plastic doors

If plastic balcony door is not firmly closed, it is easily corrected. You may encounter some problems:

• bottom cloth rubs upon expansion of the plastic threshold. This occurs due to subsidence structure which manifests itself in the summer with frequent opening of the sash, as well as heavy glass unit;
• in the middle of the web fold clatter frame member due to temperature shocks and drafts;
• insufficient web adjacent to the frame, and from the sealing material stretches cold air. This happens when there is insufficient clinging to the frame;
• if you frequently open and close the sash, the handle begins to wander. When doing this manipulation, the handle is no longer wander in the nest.

Pressure Adjustment balcony plastic doors produced with an Allen key. We need to work flat and sacral screwdriver, tape measure and a plastic gasket.

Before setting design is to determine the kind of problem. Most often, there are complexities when opening and closing the blades, when distortions, while blowing and moving the handles. If the belt crouches down and the door barely closed, then the adjustment of the individual parts or accessories made full customization of all mechanisms.

To find out if needed Door repairs, use a piece of paper. It is placed on the frame and close the door. In those places where the sheet is pulled out without problems the web is not held tightly to the box. To identify imbalances fabric should be cut around in a closed state, and then the flap is opened and the line is compared with the frame.

Helpful information! It is recommended to inspect the seal, as in the event of it cuts or cracks often appear drafts.

How to make an adjustment plastic balcony doors yourself: Video

It is easy to make the adjustment on their own plastic balcony doors, this will help special instructions.

Features of the control knob

FROM handles often occur the following problems:

• the handle is rotated to the end or not is tight. If the setting does not help, then Castle should be replaced;
• if the handle become loose, the pad turns the handle base 90 degrees and runs tightening two screws, which are hidden behind it. To do this, use Phillips screwdriver.

replacement seal

If the door is present imbalance, then it is often deformed compactor. In this case, it changing to a new with the same sectional configuration. Old material is removed from the slot using a screwdriver. Then, the groove surface is cleaned from particles of glue and dirt. When installing a new seal, it is necessary to control it to be pulled up. Before laying groove greased with glue. This should be done in areas where will be located the ends of the seal.

Helpful information! For optimum performance, the door can be equipped with opening restrictor and lifter which prevents prosidanie. The limiter prevents the hinges become loose.

What slack?

Many interested to know how to handle plastic balcony door when settling. To perform a repair should take higher leaf and move to the loop at the top. Then, the specific sequence of steps:

• flap opens in gatefold position;
• using a hexagon wrench of the screw rotation is performed next to the loop. Then, a few turns to the right side;
• to get to the element of the screw, it is necessary to remove decorative caps;
• the screw is rotated clockwise and the door structure is lifted;
• freedom of travel is checked.

Helpful information! Fitting system may be suitable not only for hex, but also turnkey star.

Setting tripping on the middle part

If you do not close plastic balcony door, then the adjustment is made, which can be seen on video. When clinging fabric section in the middle is made flaps move closer to the loops:

• flap assigned to the lower loop, and then the key is inserted into the screw and the side web is pulled to the direction of the loop;
• then the same manipulations are carried out for the upper hinge.

How to make the adjustment clamp?

Such work produces products using a locking cams. They need to move the pliers. To setup more effective, you need to read the instructions provided by the manufacturer.

Setting up several times a year. During the summer, the clamp should be weaker and in winter - a more dense. Thus it is necessary to know how to adjust balcony plastic doors for the winter.

Adjustment is as follows:

• decorative cap removed;
• located at the bottom of the canopy screw, by which the pressing force change;
• to change the clamp in the upper part, the screw itself must be adjusted;
• flap swings open and held blocker;
• Hex is set in the eccentric and rotates in the right direction;
• blocker then pressed against the seal and the flap is placed on the seat;
• cams are mounted on the place where the maximum runs clamp. When this bit is released the bolt, and then moves to the desired position.

Useful advice! recommended for lubrication fittings lube for the best design work.

Especially with the usual fittings adjustment

It is very easy to solve: how to set up a plastic balcony door, if the standard fittings.

To carry out the adjustment door is required:

• remove the decorative details with canopies;
• with Hex Wrench produced loosening screws on the back side;
• then manipulate the long horizontal screw. For example, the sash is not clinging to the top of the frame, it is necessary to lower the upper screws and leaf drop;
• It made several turns to test the design.

Related article:

What to do, if plastic window is not closed - an issue that worries many ordinary people who want to solve this problem on their own. In this paper, we consider the basic cause of the problem and deal with ways to address them.

helpful hints

To avoid having to frequently perform the adjustment of glass balcony door, do not forget about preventive measures.

You should use the following useful recommendations:

• when choosing the design of metal-profile, pay attention to the quality of fittings. These parts must be calculated on the weight of the product;
• to prevent sagging doors should be used compensator sagging and lifter. Such elements are required dimensional articles with flaps or two-chamber package;
• you need to install a limiter for the opening, which is a special bus. This will prevent the sagging canvas and seizure;
• setup should be done and corrected at least twice a year;
• for furniture requires careful maintenance.

When you install design, it is necessary to pay attention to how tightly pressed against the door to the box, as well as the static leaf in the open position and the possible shift of the vertical direction.

If the installation was performed correctly, the adjustment need not be soon. Simple ways to repair it possible to increase the service life of the door structure and its performance characteristics.