Independent adjustment of windows for the winter: features and workflow

Be in the room where the cold and drafty, uncomfortable enough. Rectify the situation helps self-adjustment of the windows for the winter, during which it is possible to change the degree of pressing the sash to the frame. We offer to find out, for whatever reason, you should make adjustments windows and how this can be done by hand.

the need to adjust

At various times of the year the temperature outside changes in a different range. Adjusting the density of the casement to the window frame, you can change the volume of fresh air coming into the room.

The need for regulation due to various weather conditions throughout the year. In winter time required to reduce the inflow of cold outside and outflows from inside heat. In the summer - on the contrary, an apartment aerate are much more likely to provide fresh air.

Attention! When installing windows often portrayed in a neutral mode. Twice a year, the system needs to be regulated.

Check the tightness of the window

Before you begin AdjustmentsShould ensure that they are necessary. Before the onset of winter perform routine inspection window system. design Tightness check:

• tactilely. It is enough to put a hand to verify the presence or absence of drafts;
• via flame. The slightest deviation from the vertical would indicate a draft. When checking the tightness of this method should retain immobility;

• using a sheet of paper left in closed window. If the design is translated for the winter, pull the paper will not be easy.

If problem areas are detected, you can start adjusting.

Control hardware status

Before the beginning of the adjustment should ensure integrity and correct operation of the hardware. Only after all the problems identified, you can start the necessary settings.

Loose clamping knob

If the draft was discovered near the handle, it is possible to talk about her leaky nip. To remedy the situation, it is sufficient to remove the top cover and twist the fixing bolts. To adjust the required Phillips screwdriver.

handle jams

If the flap is difficult to open because of the constantly seized the handle, it may be a sign of:

• the need for cleaning and lubrication mechanism. The handle is dismantled, cleaned of dirt by means of special brushes and then lubricated mechanism;
• strong press the sash. On this issue demonstrates the difficulty or impossibility of a complete rotation of the handle. Adjusting the relevant mechanisms, which are close to the handle, it is possible to correct the situation.

The handle is locked

handle lock is not a direct indication that the required complete replacement of the item. This is a clear sign that the locking mechanism is not working properly. Suffice it to change the position of the lock lever to the problem has been completely eliminated.

To do this, we understand the design features in a particular window. Some models of the lock lever looks like a tongue at an angle to the seal at the end of the window. In another case, the clamp is under seal.

The handle broke

Repairs like element is not performed. It is necessary to immediately acquire a new and install in its place. To do this, remove the decorative cover, unscrew fasteners and by a light pull staggering replacement parts. Installation is performed in reverse sequence.

How is self-adjusting window for the winter: Procedure

To manually adjust the window system, understand the type of adjusting mechanism and work performance sequence to prepare the necessary tools. We have prepared for you all the necessary information.

The types of adjustment mechanisms

The design of the windows may differ materially. Each manufacturer chooses the most appropriate, from his point of view, the type of adjustment mechanism. The most widely used:

• round pins. To determine the correct mode to be guided by the points or risks indicated in the adjustment mechanism data. In the "winter" risk will be directed inward, in the neutral will look up;

• oval pin. In this case, the "winter" will correspond to a horizontal position. Neutral mode is set by setting the pins on the diagonal;

• unions. Shifting the position in the side of the room, provide a translation in the design winter mode. In the neutral it will be located strictly in the middle.

Required tools

To change the window mode, you should prepare:

• Screwdriver Set;
• pliers;
• Allen key.

To choose the desired instrument depends on the manufacturer of the window:

• "Maso". For adjustment should be available wrenches or pliers;
• «Torx». Translation window for the winter is carried out using a spanner or screwdriver;
• «Roto». To work it is necessary to have in place special round head. perform the adjustment is not possible without them.

Comment

Sergei Kharitonov

Lead engineer for heating, ventilation and air conditioning "GK" Spetsstroy "

Ask a Question

«To increase the service life of accessories should prepare a special spray or engine oil to be able to lubricate the friction elements. "

Window Control: sequence of actions

To manually transfer window to "winter" mode, you should:

• open the window and see the ends carefully;
• determine the type of adjusting mechanism and its position;
• prepared using the tool, mechanism to translate into the desired position.

Attention! Adjust windows executed before frost at + 5-10 ° C.

We offer watch a video, which clearly describes how to change summer / winter mode:

If the work performed does not give the desired result, perhaps, of rubber seal is worn and must be replaced. To this end, it is removed from the slots with a standard screwdriver. It should not be much pull. Then, picking up the product with the desired profile, secure it in place of the remote.

Tip! Extend seal life can be, if every six months wipe it with silicone gel.

Share in the comments, if you do own the adjustment of windows or invite experts.