Primarily for creating fitokartiny it requires a base which is mounted behind the window frame, thereby forming a space for a bed. This framework consists of a rectangular outer frame and an inner cross made of six wooden bars. The exact length of the bars depends on the size of the window frame used. The size of our window frame - 30 × 60 cm.
During step 1 it is necessary to determine the dimensions of the bars to the base. That the base was not visible in the finished film, the measurement of line must always be aligned to the bars of the window frame. All four bars are required for the outer frame. The length of the first two bars must correspond to the height of the frame used on the outer side, and the length of the other two - the distance between the first two vertical bars on the inside. Internal cross consists of a horizontal bar of the same length as that of the aforementioned horizontal bars and the vertical length bar must correspond to the distance from the lower horizontal bar to the highest point of the arch of the window frame on the inside.
Note pencil measured distance at two wooden bars, and then cut them via markup AdvancedCut 50 saws. It is important that wooden blocks at the same time were firmly fixed on the bench screw terminals.
Now you need to assemble the frame of the base. To do this, place the cut bars (except for the vertical bar inside the cross) so that they form a single frame. Mark the center of the two vertical bars of the frame points for three holes: one in the middle and the other two - the left and right respectively disposed opposite the horizontal bars.
Using drill PSB 18 LI-2 Ergonomic and 3-millimeter drill wood drill one hole in each of the six selected points. Now screw the screws into the drilled holes in the frame.
To create an internal cross take a long vertical bar and place it in the center of the frame. Since it is inserted into the frame through the slots, first mark them on the top two horizontal bars. The first vertical bar mark width.
The depth of the grooves is equal to half the width of the vertical bar, i.e. in this case 1.5 cm. Then mark on the vertical bar dimensions upper two horizontal bars.
Using a jigsaw PST 18 LI saw out grooves according marks. You can then insert a vertical bar in the frame slots. Tip: For a more secure attachment before inserting the bar can be applied in the grooves a little glue for wood.
Now put on the reverse side of the window frame basis. Bend veneer sheets arc above the highest point of the upper projecting portion of the window frame and fix both sides screw. Then select the desired width and length. To veneer sheet could be stapled to a base, it must act at 1 cm from each side. The width of the veneer sheet depends on the depth of construction - it allows them to be combined.
Attach it to the protruding upper part of the frame, using a stapler PTK 3.6 LI. In order to avoid irregularities initially secure the sheet to the left, then top, and then - on the opposite side.
Now we need to prepare the rear side of the base. To put this on a base sheet of a poplar plywood insert dimensions, cut along a line through the jigsaw PST 18 LI and fix to the frame by means of a stapler PTK 3.6 LI.
Put on the back side of the window frame wire mesh. So that it does not move while cutting, clamp it with a base. Using pruning shears, trim EasyPrune mesh size of the window frame. Then put the base and tighten the net on the back side of the window frame using a stapler PTK 3.6 LI.
To then attach the base to the back side of the window frame by a screwdriver IXO (with an eccentric nozzle) tighten each of the four corners of the metal to all corners of the window frame with the two screws (3 x 14 mm) in the vertical position.
Almost ready! Now place on the back side of the base of the window frame and connect them with metal parts. If you plan to hang fitokartinu on the wall, you need using the screwdriver IXO and four wood screws (3 × 14 mm) attached to the rear wall of the frame two flat mounting plate. One flat fixing plate screwed in the center of the highest point of the arched portion, and the second - in the center of the lower horizontal bar.
Now you can fill fitokartinu ground. Use a spoon handle to push the ground through the wire mesh. Before planting succulents need to carefully free the roots. Then c using a wooden stick slip the roots through the wire mesh. The plants have remained in the same position after you hang pictures, leave it in a horizontal position for about two weeks, because only in this way will strengthen the roots in the ground.
To hang a picture of flowers on the wall, drill two holes in the wall using a drill PSB 18 LI-2 Ergonomic and 7-millimeter Drill suitable for your wall type, then insert the dowels, screws, screw-half rings (7 × 120 mm) and hang the picture plane via fasteners plates.
