Knocks out the machine when the washing machine is turned on

Most likely, there is no such person who would not know about traffic jams. But this is not the traffic jams that are encountered on the roads, we are talking about traffic jams in the switchboard. And the problems with them can spoil the life pretty much, because about what comfort, tranquility and comfort in an apartment or a private house can there be a talk if for the flow of electricity and the presence of light you have to constantly run to the switch? For example, there is a situation when the machine knocks out when you turn on the washing machine - what does it mean? The reasons for this phenomenon and how to deal with it you can learn in this article.

to the contents ↑

What to do when the washing machine knocks out plugs?

Your washing machine just worked in normal mode, the drum measured the laundry regularly - and for no reason there was silence, all indicators went out, the unit froze, and throughout the apartment all electronic devices stopped working. What happened? Most likely - knocked out traffic jams.

And if still you could get to the Internet, most likely, you managed to turn on the light. Suspicions for all this confusion, naturally, fell on the washing machine, as the most voracious energy consumer. However, your device may not have anything to do with it, if there are such factors.

Washing machine new and newly installed

Just in this case, most likely, the problem is in the wiring or in improperly selected power protection devices. For example, if you have installed an RCD or your machines have insufficient electrical capacity.

Important! You can be sure that this problem is in the wiring itself, by including in the same outlet any other electric appliance that will have a similar power of 2-2.5 kV - an iron or a kettle will do.

If the traffic jams are knocked out again - time to sound an alarm, and after - to run to seek help to an electrician!

During the operation of the washing machine, many other

electrical appliances were simultaneously turned on. This is a classic day off: on the stove, lunch is cooked, the washing machine is washed, a Saturday cake is baked in the oven, and you also decided to vacuum it.

Perhaps your power grid simply could not withstand such a huge load. Especially when the machine entered a particularly active phase - pressing or heating. As a result - knocking out the machine when you turn on the washing machine, the apartment is now quiet.

Important! For greater security of household members and the house, in this case it is again better to turn to an electrician for help. In particular, if earlier your network could withstand such a load.

Fork or cord of washing machine short

If damage is visible with the naked eye - the cord with the plug must be replaced. It is better to entrust this procedure to a specialist.

You can check the integrity of the power cord with a multimeter. To do this you must:

• dismantle the bottom panel of your washing machine;
• unscrew the fixing bolts;
• then simply remove the network cable;
• then ring the veins of the wire to determine the location of the breakdown.

Important! Probably, the wire is absolutely whole, but the clamps are burnt, in this case they need to be replaced.

In all other cases, unfortunately, most likely, that your washing machine has a breakdown. You must immediately disconnect the washing machine from the electricity supply and call a specialist.

Important! It is highly advisable not to include the already knocked out machine if the unit has not been disconnected from the outlet. This can be extremely dangerous - both for the entire power grid, and for those who live in your apartment.

to the contents ↑

Problems in electrical communications - what do we do for this?

The machine creates a sufficiently large load on the mains during start-up and operation. Therefore, in order to connect it, it is necessary to use a separate network, which will be protected by RCDs and Difa Automats. The wiring of such a network also has special requirements. You must use the VVG cable 3x2.5.

Important! With all this, it does not matter which machine will need to be connected - the one that has a drying function, or one that does not have one.

In fact, the washing machine is connected in all possible ways:

• in a common socket with other kitchen electrical appliances;
• with an extension cord;
• happens even - with the help of an adapter.

This - by itself leads to overheating, and of course - to the damage of the wiring, the power grid, the socket housing can begin to melt, after which the protection system is triggered and the network is de-energized.

Important! To find out the problem with electrical communications in most cases is not difficult:

• shows darkened wiring;
• reflow outlet;
• smells of burnt plastic and insulation.

to the contents ↑

How to fix it?

In order for the problem not to be repeated again, and you did not think about knocking out the RCD when you turn on the washing machine:

• Run a separate network that will feed your washing machine according to certain schemes that must be available to electricians.
• Use sockets with a housing that is protected against moisture.
• Use devices that will purposefully protect the network.

Important! Under no circumstances should you try to connect the washing machine with an extension cord, adapter and other similar devices. Extremely dedicated socket and extremely direct connection with a power cord.

to the contents ↑

Problems with button contacts and the network filter

In addition to the above reasons for knocking out the machine when the washing machine is turned on, there are others. Here are some of them.

Cause 1

If you have already tested the power cord, finally made sure that it is working properly, then - the problem can be covered in the network filter.

Important! This device, which is called a network filter, is the same part to which the power cord is connected.

In some cases, manufacturers of washing automatic machines combine the power cord together with the barrel of the mains filter. That's why you have to change two elements at once.

Important! A filter is not a repairable part. That's why if you, having tested it with a multimeter and visually inspected, found a malfunction, you should prepare to replace this element.

Cause 2

In some cases, the washing machine knocks out the machine for the reason that the weak connection of the wire contacts together with the mains filter. From this, respectively, burn contacts - both the wire itself and the filter.

Important! In this case, do not attempt to clean the contacts - they must be replaced together with the mains filter. If you do not do this, there may already be new interruptions, as well as overloading in the power grid.

Cause 3 The

may be knocked out by the RCD due to a faulty control panel button or due to a malfunction of all buttons. Why is this happening?

The main problem lies in the fact that the contacts themselves buttons eventually wear out. If you click on the faulty button, the contact breaks, resulting in an overload.

What should I do in this case?

1. Disassemble the washing machine by removing the control unit.
2. Use the multimeter to call the on / off buttons of the washing machine.
3. Call the multimeter contacts of all other buttons, and do not forget the wires that go to them.

Important! Most often, the machine or plugs are knocked out because of the malfunction of the on / off button. Therefore, in order not to shovel the entire control panel for nothing, start with this button.

to the contents ↑

Problems in the control unit, wires and terminals

If the faults of the button are not detected, then - proceed with the meticulous work, during which you will have to check all the contacts, wires, terminals and sensors. Once you have previously disassembled the control unit, start with it. Alternately, ring absolutely all the wiring, starting with the most suspicious elements that have traces of carbon deposits, scuffs and the like.

Important! The control unit is a rather complicated device. Therefore, even if you understand the electrical and elementary level can be controlled with a multimeter, it is better to give it to testing in the hands of specialists. It is likely that you will miss an important malfunction.

Also the problem can be covered and not in the control unit. The multimeter must call the contacts and wires that go to the engine, heater, drain pump and other units, as well as their sensors.

Important! During the inspection, it is necessary to change absolutely all burnt elements, even when they work. After all, you do not want to disassemble your washing machine again because of some sort of wiring.

Now you know about all the possible reasons why the machine knocks out when you turn on the washing machine. We hope you just used improper quality carrying, and you did not have to spend a lot of time with the help of qualified masters in the control unit to again wash things quickly and conveniently.