How to disassemble the blender Brown?

blender analysis Blender is an integral component of every kitchen, it is capable of mixing, grinding, whipping everything. In order for it to always work perfectly, it must be cleaned from time to time, but how to disassemble the blender Brown? To deal with this issue, you need to know also why you are disassembling how to repair, and should have an idea of ​​the basic blender problems. This will be discussed in this article.

to the contents ↑

Preparation of tools

In order for you to be able to disassemble the brown blender yourself, you will need these tools:

• pliers;
• thin, narrow knife or a thin and flat screwdriver;
• flat and long screwdriver;
• glue intended for aircraft models or superglue;
• hammer.

to the contents ↑

Sequence of the work of

To correctly disassemble the Brown blender and not to damage its important parts, proceed according to the following algorithm:

1. With the help of pliers, remove the holder of the nozzles, also called the cartridge.
2. Take a thin and narrow knife or screwdriver, slide the tool between the casing and the body, and lightly strike the hammer with a welded seam.
3. Repeat this action on the body perimeter until the motor with the casing will not move freely inside the casing. Be extremely careful near fixatives - under no circumstances do not beat them. Also, do not use a wide knife or a thick screwdriver, because the entire thin outer casing can burst.
4. Then dump the latches and remove the motor.
5. The motor itself can be pulled out together with the control board itself. In the event that this does not happen, pull with the help of pliers on the edge of the board - due to this it is easily extracted.
6. Inside you will notice 4 latches from the back cover. Bend these latches on the arrows, as a result - the top cover will be in your hands.
7. Push the speed control cover with a screwdriver. From the inside, bend off all the external clips of the network cable holder.

Important! Be cautious in handling the board, because it is fragile enough.

to Contents ↑

Basic Faults and Construction

This device is quite simple throughout its structure. Basically the blender consists of such components as: electric motor, nozzle and bowl, but it is only in a stationary blender.

But blenders themselves are divided into two types:

1. Manual, they are also submersible - the best are the models from Bimatek BL, Krups, Kenwood, Orion.
2. Stationary - popular variants are presented from the brands Gorenje, Moulinex, Panasonic, Zelmer.

Important! Hand blenders are a motor with a handle to which the nozzle is attached. The key difference between a submerged hand and a stationary blender is the principle of their operation:

• The food is placed in the stationary cup, which is cut with knives, which are located on the bottom of the bowl itself.
• Manual directly immersed in the container - quite often it is a special glass, and cuts everything at any level.

to the contents ↑

Basic malfunctions of the

technique Faults can occur in any model of technology, but since not many can afford very expensive options, often on the forums there are questions as to how to disassemble the blender Brown and what may be his faults.

The

does not rotate. This problem lies in the knife speed switch.

The blender does not grind or work poorly.

The power of the work plays a very important role in the blender as well as in the mixer. If you have chosen an insufficiently powerful or qualitative type, the efficiency of the work itself will be low.

The device does not respond to the

network connection. It is likely that something stuck inside the chopper or the engine burned out from overly intensive work. In some cases, this reduces the voltage across the entire electrical network.

Modes do not switch.

Most likely, this is a drive problem or a control system.

Broken knives

The most common problem. These parts from the blender can be purchased in almost any of the branded stores Redmond RHB, Vitek, Scarlett, Braun and so on. They can not be repaired in any way, that's why a replacement is being made.

The device does not want to turn on the

If the gearbox is defective, the appliance will most often not be turned on - it is extremely difficult to carry out such repair of the blender brown yourself. Instructions for replacing the engine:

1. You must disassemble the device according to the scheme described above.
2. Be sure to read the manufacturer's recommendations, as well as the technical specifications of this device.
3. Check the power button, as well as the lock - perhaps the problem is in it. If you hear a buzz while turning on the blender, you should press the contacts and then test them with a multimeter. In some cases, they can not close during power-on.
4. Separately, engines can be purchased in specialized stores, but such parts are sold separately only for expensive models or for food processors such as Kenwood HBM, DEX DHB, Polaris PHB, Gastrorag.
5. New engine mount in place of the broken, assemble and check the entire system.

Important! In models that are not inseparable, such repairs are not practical, because of their high cost.

to the contents ↑

Blender repair instruction

Before repairing the device, disassemble it. We must warn you immediately that the disassembly of submersible blenders Saturn, Bork, and also Vitec is impossible. Usually their design is a molded plastic, and in the base soldered some plastic ring, which can not be removed.

Therefore, you have only 2 options to solve the problem, in case the device has broken down:

1. Immediately purchase a new one. Much to our regret, not each of the service centers can provide warranty repair of such blenders.
2. Solder the panel itself. In order to connect the body, the technology of soldering plastic is used, as a result of which the disassembly can be carried out using high-temperature technology. Carefully cut the body and insert several small metal plates or needles into the cut. Spread them and remove the melted plastic. After the repair, the plastic can be re-glued.

Important! In the body itself is the entire working part of the blender, namely: the motor, the spindle, and also the control unit. This block is a circuit that helps to configure all modes and options. After disassembly, you can replace all necessary parts with workers or clean the contacts of your device.

to the contents ↑

Analysis of the stationary blender

The situation is somewhat more complicated in the disassembly of a stationary blender. It consists of a bowl of a special shape, often cylindrical or trapezoidal, a shaft, a knife, an electric motor, and a spindle.

When the device is turned on, the shaft together with the spindle transfers the torque to the knife, which acts as a moving and chopping product inside the bowl. In order for the milled food not to fall out through the expanded top, the bowl is covered with a lid.

Important! Rotation of the knife in some blenders can be done for a certain time - some models of Polaris, Mulinex, and Redmond have a special timer built into the system, or until the moment when the contacts open.

In order to disassemble a similar blender, you will need a screwdriver or a wrench - it all depends on the type of fasteners:

1. The housing cover is fixed with screws or nuts, preferably with a left-hand thread. Unscrew them and remove the case.
2. Under it are the engine, shaft, spindle.
3. First of all, inspect the shaft, on it in any case should not be a notch, obvious unevenness.
4. Next, if necessary, you can change the knife. In the event that your knife is blunt, then you will not be able to imprison it from you. But you can buy it in the company store. To remove the old knife, unscrew it from the spindle.
5. In some cases, the knife is not seated on the thread itself, but on the nuts. In this case, unscrew them, and the knife, the blade, gently remove from the nest.

Important! At the junction of the knife, together with the drive, there is an oil seal - it acts as a sealant, which significantly improves the grip of parts, and also increases the torque. This stuffing box should be changed every six months, of course, if the model is collapsible.

We hope, following our instructions, you managed not only to disassemble the blender, but also to identify its malfunction and even eliminate it. But if you have no idea about repairing household appliances, do not risk - take the device to the master better, so that it corrects the situation. Otherwise - by your actions you can achieve only that the valuable device completely fails and you will have to buy a new one.