As with their hands to collect mobile construction goats

For any of the builder it is important that the tool is in order, and the working conditions were extremely comfortable. For this purpose, special premises using goats and benches. And if you're "on the road", it is very handy mobile table, on which it would be convenient to work carpentry tools. Master class on the construction of the goat to the editor sent HouseChief Olga Spring of Tver. It must be admitted that in this case the beauty and craftsmanship of supplement each other.

Hello everyone! If you are a builder, the word goat - has neither abusive to you, nor animal, nor sporting sense. Here I can not explain why that one word has many meanings. The result is not less than four, right? Since the fourth sense - building. Goat or kid - is a vital tool for all, who is engaged in repair and construction. And not only to work better, to the goat "riding", that is, to move from place to place. Since today you do repairs in one room, tomorrow - another, and the next day - on the veranda. So I decided to build such a construction of the beast for their needs.

Read article

1 The back of the goat - worktops
2 Goat legs and a shelf
3 As my goat was the electrical and fluid
4 There is nothing superfluous: the mobile trashcan

The back of the goat - worktops

Let's start with the materials that I needed:

Wallpaper took me plywood sheet, couple with the pieces of timber bound in a 5 cm and 12 cm wide boards deuce

To begin with sizing countertops, which will be the basis of a sheet of plywood

The width should be such that the finished goat passing through doorways in the house or apartment. Otherwise there will be no good, and stuck all

So I took the width of 5 cm longer than the doorway, and the length - the size of a plywood sheet, although it may be shorter, if you prefer

To cap screws to the attachment points are not sticking out, I used zenkovku - a special attachment to the drill, which makes small holes

To frame my handy bar: I mark out and cut it so that collected under

Frame countertop is very simple - at the ends of beams fit between the longitudinal parts

Mounting frame - laterally. First, make a hole with a drill, and then spins a pair of long screws. Thanks to everyone who has invented an electric drill and screwdriver

The final step in the construction of countertops - fastening veneer sheet to the frame. I did it with the same screws into the holes razzenkovannye

Goat legs and a shelf

My goat must be stable legs, because I'm not going to just move it around the apartment, but also, to climb on top of it, if necessary.

Legs I made out of the board. I accurately calculate the height of my instrument and cut 4 parts

A bit of height. Since the device is required for operation with the ceiling, which means that its height should be as follows: the distance from floor to ceiling minus 10 cm, minus builder growth. This is the optimal size, which enables comfortable working at a height.

For greater stability, the legs a little bit, I cropped, approximately 1 cm from one end

It is attached to the frame with screws through the legs. To board does not burst, first make a hole using a drill

Construction goats - this is not just a table, it is also a means for moving the tools and ladder, so you need to make the bottom shelf.

Shelve is located approximately mid-height legs

On one end, where it will be used as a ladder, I attached the cross bar from a bar

At the other end, where it is required only to support a shelf, can be dispensed pair of timber pieces. Although to no end not to look under the table for determining which end becomes possible, better to put a full timber at both ends

You need to cut the shelf from the same sheet of plywood and carefully sand the edges to avoid collecting splinters on his feet

Shelf needs to be fixed on the cross member, the holes for screws is also better razzenkovat

So when moving tools are slid goat, you need to make a jib. I used for this metal beacons

As my goat was the electrical and fluid

So, when the basic structure is ready, it is necessary to add additional features for comfortable work.

To install a power strip, I made three round holes in the table top

I put an extension cord, securing it from the bottom of the metal perforated tape

Pieces of plywood that had been cut special drill was used as lids to the wall outlet does not enter into trash

I hooked the cover with plastic cable ties by threading them through the drilled holes.

Silent departing from the subject, I will say that it is better to be done the outlet side of the table top, not on it. The top position, without a doubt, it is convenient, but I was all the time haunted, what would happen if I accidentally spill something on this table, such as paint thinner. I thought this was not exactly pleasant.

For fixing a long extension cord, I adapted the 4 screws on the inside of the legs

Extension to the plug is inserted, the side fastened very cheap outlet, which found in the store

Now I had to give my mobility tool, because you will need it to me almost all the rooms.

To do this, one end on the legs I cut recess and established here such small wheels. Now you can roll the table, raised at one end

To stem not scratch floors, pasted on them felt strips

Goat I turned nimble, so that first experience resulted in damage to the drywall on the wall. To avoid such confusion, I rounded edge countertops

The table has turned stable and comfortable, I checked it out on their own experience

There is nothing superfluous: the mobile trashcan

Sorry for such a positive comparison, but do you know why the horses that drove the city chaise, tying the drain bag? Yes, for this very reason, to preserve the purity of the pavement. That's my working goat obzavolsya such a device.

I cut off the rim of a bucket of paint and cut the lid. Between the rim and the lid can be fastened trash bag. And the band has recorded a movable holder

I hope my building animal you like. I would be glad if someone can help my experience in the repair

Thank you, Olga! Charming master class from the real masters! Your work a pleasure to watch. We even have nothing to add. The only thing you can do - offer complicate the task, in this short video on creating multi-joiner table:

We look forward to your impressions and comments, as well as new materials in the category "not a woman's business!"

Photo: Olga Spring

As with their hands to collect mobile construction goats

The back of the goat - worktops

Goat legs and a shelf

As my goat was the electrical and fluid

There is nothing superfluous: the mobile trashcan

About us

Categories

Latest