Sometimes there is a desire to buy a mirror of any intricate shape, but in the stores is quite difficult to find a non-standard items. Of course, you can take the help of a specialist, but if you come to this page, it means, it is assumed that the cost and without him. The most important thing in this case - to handle the product very carefully and strictly follow all the rules and guidelines. If you are capable of it, cutting does not seem like a heavy thing. Why not try it? It is always interesting to learn something new.
Sometimes there is a desire to buy a mirror of any intricate shape, but in the stores is quite difficult to find a non-standard items.
Content
- 1 Safety in the glass cutting
- 2 Required tools
- 3 How to prepare the glass for the procedure?
- 4 Getting cut
- 5 It is done!
- 6 VIDEO: Cutting a mirror
- 7 50 photo ideas how to cut the mirror at home
Safety in the glass cutting
Before you cut the mirror glass cutter, read the safety requirements.
- Give workplace in order, remove from the table all unnecessary. Place the boxes of scraps, tools and the product itself in place.
- Make sure all devices are OK.
- Put on a pair of pliers on sponge rubber tip or anything wrap.
- glass boxes are always installed vertically.
- Be sure to use a special suit, gloves and goggles.
- Take your time and try not to make any sudden movements.
- Do not touch the glass cut-off fingers, not protected by gloves.
- It is forbidden to cut the product on subjects that are not designed for this purpose.
- When working at height can not be discounted glass bottom. Always take the whole glass cutting and suicide.
- Cutting is allowed to produce only in the opposite direction to the cutting part.
- Install glass need to have solid support with a slope up to 15 °.
- In operation, place unnecessary scraps in a box and send them to the accumulation of trash.
- Remove the glass from the drawer gently. If the glass is cracked, reach for its individual pieces.
- You can not cut the product on your lap.
- Use a glass cutter electric carefully.
- If the product is brought from a cold, be sure to thawing it.
- Sweep the floor clean benches and special brush. Do not try to blow off the glass dust.
- Before you finish the job, thoroughly shake the special suit, clearing it from the crushed glass particles.
First, the entire surface of the mirror must be thoroughly cleaned and rinsed soda solution.
Place, which will be cutting, should be smooth to mirror closely laid on the entire surface.
Required tools
Be sure to verify that all material before cut mirror. Buffet will suit most standard, most importantly, to match the dimensions of countertops mirror surface area, ideally - surpassed her.
zvestna two types of glass cutters: Diamond roller, and a mirror at home can cut and so, and others.
If you plan to insert a mirror in a frame, it obzavedites advance.
Then the line is necessary to make the line better metal.
The work should be carried out carefully, slowly.
The most important instrument - is, of course, a glass cutter. Tools that can be used to cut the glass in the home, there are three types:
- roller - cutting part is made of highly durable alloy;
- Diamond - as a cutting portion used technical diamond;
- oil - have the same characteristics as the roller, there is an additional tank.
This technique allows you to control the correct position of the cutting part of the glass cutter and ensures that the glass cutter does not come off with the line on the line.
If wondering what kind of glass cutters should buy, choose the diamond. It surpasses the roller both in quality and in service life.
It is understood that the cutting element should be located strictly in the marked line and perpendicular to the mirror surface.
During operation, the glass cutter tightly to the surface of the mirror and the line.
Another essential tool - a special thick line or polygon for cutting glass. However, it is possible to use conventional metal line, we just need to improve it a little. To do this, you will need several pieces of rubber or leather. They need to put a line. This will prevent sliding of the metal on the glass and lift the line at a sufficiently high level to stop stekloreza.
Pressure and movement of glass cutter should be smooth and progressive.
You will also come in handy pliers and a hammer, which is designed to facilitate the process of breaking glass by tapping the mirror on the reverse side. It is desirable that the hammer was small.
With proper cutting on the surface of the mirror will be a thin white line.
Specialist capable of hearing to determine the correctness of the cutting - the characteristic light cod.
It is desirable to cover the tabletop coverlet. The fabric should be genuine and to have the necessary density, because in it you will manipulate the mirror. If you do not use a blanket, on a solid surface a delicate glass table can crack at any careless move.
When the line is cut ready, mirror lies on the edge of the surface (table, bench, stool).
The final element - the water-soluble felt-tip pen or wax pencil to mark.
If this does not work, then you need a small hammer to knock the bottom of the line, moving the hammer from the distal end thereof to him.
How to prepare the glass for the procedure?
To cut the line no further "left" side, the first thing you need to clean the surface of the product and wash with baking soda. If the stains and dirt is hard to remove, use alcohol. An old mirror will help clean up the special liquid for glass. do not wipe it with a cloth after cleaning is necessary, since it is necessary to leave the unnecessary fluff.
Thereafter, if the piece is not separated, the cutting process must be repeated.
If you purchased the mirror only that, it must be for a couple of hours left in the room where the whole cutting process will be carried out. During this time, the product adapts to the temperature and humidity of the room. Then, if the mirror lay before in the box, wipe it with paper towels.
If possible, better to buy a diamond glass cutter - he cuts more efficiently, and its life longer.
Make sure that the place where will be sharp, perfectly smooth, otherwise the product will not be able to lie on the surface tightly. Remember the soft blanket that need to cover the table surface. Place the product in the workplace reflective side up.
When cutting glass is better to use goggles.
The main thing - to do the job safely and accurately, and then you will succeed.
The next stage - marking the cutting line. Remember the adage "look before you leap - cut once"? For our situation, it fits perfectly. After the measurements accurately perform cutting line wax pencil. Then, attach a metal ruler. Do not forget to put under her pieces of rubber or leather.
In some cases, to remove the cut fragments of thin mirrors are used pliers with rubber gaskets.
Now you need only to insert a mirror in a prepared frame.
Getting cut
Glass cutter must be positioned at a right angle to the mirror surface is strictly on the marked line. Slightly pressed to the glass, it is necessary to accurately maintain the direction that leads to you. Do not hurry. Gently and precisely move the glass cutter along the marked lines. If you hear the sound of the cut glass, so everything is going well. Creaking says that the glass cutter is broken or you're doing something wrong.
An old mirror will help clean up the special liquid for glass.
With proper cutting on the glass, you will see a thin line. If all goes well, put a mirror on the workbench so that the line slightly beyond the edge. Then just push the severed part with the other hand holding the second. The glass should fall off. If it does not, prostuchite hammer the entire line from the bottom side, moving it in the direction of ourselves. Does not work? Repeat the cutting procedure again. Small fragments are removed with pliers.
If you purchased the mirror only that, it must be for a couple of hours left in the room where the whole cutting process will be carried out.
Attention! If you do not have special glasses, while working does not bow too low, in order to avoid getting splinters in the eye.
Creaking says that the glass cutter is broken or you're doing something wrong.
It is done!
The work is almost finished. Now you need only to insert a mirror in a prepared frame. If not, cover the sharp edges with sandpaper in order to protect themselves from the cut.
With proper cutting on the glass, you will see a thin line.
As you can see, glass cutting procedure is not so complex. The main thing - to do the job safely and accurately, and then you will succeed!
. If all goes well, put a mirror on the workbench so that the line slightly beyond the edge.
VIDEO: Cutting a mirror
50 photo ideas how to cut the mirror at home
