Washing machine does not wring - causes

The automatic washing machine, according to housewives, is considered one of the most important inventions designed to facilitate their work. The machine perfectly copes with its function: it erases, thoroughly rinses and squeezes out the laundry. Sometimes it happens that the washing machine does not wring. The reasons can be different, we will discuss them in this article.

to the contents ↑

Should I look for the cause of the malfunction?

If the automatic machine refuses to squeeze out the laundry, then the mistresses who have caught the times of "manual" labor can think, the situation is not very critical, because the main job is washing and rinsing, the machine still performs.

However, if the washing machine does not press - this is the first bell, which warns that the unit needs repair. Otherwise, when the device is further operated in such a semi-working mode, not only the spinning, but also other functions can break.

to the contents ↑

Why does not the washing machine press?

If the washing machine LG, Indesit, Samsung, Candy, Ardo, Bosch, Ariston does not wring out, then first make sure that there is a breakdown.

The greatest pleasantness of the situation when the washing machine does not press - the reasons can be absolutely not serious, for example:

1. Perhaps you have loaded too many things into the styralka( or one big one).In this case, the laundry is not evenly distributed over the drum, the machine automatically reduces the spin speed in order to prevent a strong vibration.
2. Check if the program is selected correctly, because you could accidentally exclude the spin mode from the washing cycle and start the machine.
3. Some of the above machines allow you to adjust the number of revolutions per minute. Perhaps you accidentally dropped them, as a result - the laundry was too wet.
4. To a harmless type of problems is the clogging of the sink. Perhaps there was a clog, then - the washing machine does not press just because it can not drain the water.

Prevention

If you are faced with such harmless, not serious reasons for not squeezing, then use the following recommendations:

• Keep track of what you put in the washing machine and how: if it becomes necessary to wash a large thing, then put a few small. Then the machine is brilliant to cope with any pressing.
• Regularly monitor the drain system. In the event that you have to wash very dirty things or you operate the machine for more than a year, plum can be blocked. Periodically carry out preventive works on cleaning the drainage system.
• Be attentive to the selection of the washing program. Study the instruction to press exactly the buttons that are necessary when washing these or other things. While the equipment is in operation, keep children away or watch closely that they do not press important buttons.

to the contents ↑

How to know the complexity of the problem?

Before searching for terrible machine failures, check it in the following steps:

1. Unplug the machine from the mains( to avoid electric shock).
2. Check pump filter for clogging.
3. Carefully study the impeller of the drain pump. Perhaps it does not hold well and is the reason for the impossibility of draining, and therefore - squeezing.
4. Explore the nozzle that connects the drum and the drain pump to the jam.
5. Examine the pump itself. Pump failure is normal, so if it is unusable, it is better to replace it.

to the contents ↑

How to determine if the washing machine does not drain water and does not press?

To determine this fault, just look inside the washing machine through the access door( do not open the hatch).If you bend over and look inside the machine, you will see the water that has not merged, then the problem is not in pressing, but in the drainage mechanism.

In this case, the spin mode works fine, however, due to a malfunction of the pump, there is no outflow of water to the sewer.

Manufacturers of automatic machines provide such a situation: if the water from the tank is not gone, then the spin program will not turn on. After the pump is replaced, the operation of the styralke will be restored.

Important! If you checked the spin system and determined that it's not a matter of the blockage and the pump, and also the incorrect laying of the laundry, it's not to do with anything, then contact the specialists. Most likely, more serious and independent repair attempts will not succeed.

to the contents ↑

Serious breakdowns or why the washing machine does not press the laundry

A number of reasons why the washing machine does not wring may depend on the technical characteristics. Removing serious damage can only be specialists in the service center.

Experts consider the most common failures:

• Water level sensor malfunction. If the pressure switch is operating normally, it informs the machine control module of what level of water and whether it is necessary to squeeze or not. If the sensor fails, the control module does not receive a signal that the water has remained. As a result, the spin mode is not activated. To correct this problem, you need to replace the sensor.
• Faulty electronic module or programmer( depending on the machine model).If the stabilizer in the control module fails, the "brain" of the machine does not give the squeeze command. To fix the situation, you need a replacement board or flashing.
• Breakdown of drum motor of washing machine. Causes of motor failure may be:
  1. Open in the winding of the drive motor.
  2. Wear of engine brushes.

In any case, a washing machine requires a qualified inspection, repair or possibly replacement of the engine.

• RPM sensor malfunction. If you, in spite of the instructions, regularly load a lot more things into the tank than allowed, then this operation may break the vehicle. It is he who performs the function of controlling the number of necessary revolutions of the drum during the washing cycle. If such a breakdown has occurred, the system will not accelerate to the required speed, as a consequence - the washing machine does not spin at all or does not perform this job qualitatively enough. In the event of a tachogenerator failure, it must be replaced. If, however, the screw that fixes the sensor is weakened, then it is necessary to tighten it.

to the contents ↑

Prevention

To protect the home appliance and not solve a problem like the stylalky does not wring, as well as other troubles, we recommend adhering to the basic rules:

• Before washing, be sure to check the contents of the pockets of things, as any rubbish( candy wrappers, coins andother forgotten things) is the main cause of blockages.
• Be sure to maintain the recommended load weight of the laundry. Do not overload the washing machine - this will also save the drum motor from overload and rapid wear.
• In the course of washing, use the required amount of powder, always just a high-quality detergent. Remember that excess powder damages the water level sensor.
• Be sure to use surge protectors with surge protection( voltage regulators).The control modules of the washing machine are most sensitive to power surges in electrical networks. Always remember that replacing control cards or reflashing is one of the most expensive repair operations.
• After the washing process, be sure to clean the machine. A tray for a powder and the conditioner clean of the rests of a washing-up liquid. Wipe the drum rubber from debris and powder residues. During maintenance and cleaning of the washing machine, give preference to non-abrasive products so as not to damage the surface of the machine.

Follow simple rules and recommendations of the manufacturer of home appliances, then you will not remember about manual washing.