Chair covers with his hands 105 photo ideas and patterns for sewing

click fraud protection

People have different preferences about whether to use the chair covers. On cape sit comfortably, it protects the chair from damage. However, it is quite difficult to clean. Some apartments in the winter is too cold, so people are forced to spend money on the warm covers for all seats, and sometimes even sofas. But the lifetime of the furniture increases. The ideal option would be a handiwork, but the road from the store, and made their own hands. This hack will be an important part of the decor. You must learn how to properly measure the chairs and a little guided in performing styles. Invented many turn-based workshops on the creation of these products. You can also purchase a seat with upholstery or ready covers, but the latter are hard to find, easy to clean and separate models are even more rare. Cushions are bought mainly for the kitchen.

Content

  • The advantages of using slipcovers for chairs
  • A variety of models
  • styles covers
  • The choice of fabric
  • How to take measurements from the chair
  • Drawing and transfer the pattern on the fabric
  • Fitting and advice on tailoring
  • Variants of covers with their own hands
    • Cover a chair with the back of the fabric
    • Seats with their hands
    • Cover on a round stool
    • Knitted crocheted blankets
    • Cover of an old sweater
    • Dress chair
    • Cover for highchair
    • Covers in patchwork
    • Covers for legs
    • Case for office chair
    • festive Case
    • Wedding cases
  • conclusion

The advantages of using slipcovers for chairs

The benefits are much greater than the disadvantages. The first quality that is worth noting - low price. In addition, the cover can be made with your own hands. It is not necessary to know how to sew. Enough to wrap a chair with a cloth and loose the raw edges just leave hanging. Cover protects the seat from dirt, water and fat. This is a fundamental nuance for locations such as the kitchen. The appearance of the interior can vary or change with the help of covers. In winter preferable to use cold tone, in summer - warm or vice versa. At every time of year is best to do covers of different thicknesses. Another functional purpose - the protection of domestic animals from their "footprints" and claws. Thick mantle not necessarily washed sufficiently thorough cleaning with a detergent and a brush. This is a practical thing that can be stylish and beautiful.

For comfortFor greater comfortTo create a styleTo create comfortUpdate the old furnitureFor special events

The use of covers can save a lot of money on buying new furniture or repair old!

A variety of models

They come in one piece and split. The second subtype may consist of several parts connected or Velcro. There is a wide variety of poluchehlov. They are intended mainly for the seats, but at various ceremonial events and ceremonies can see options only for the backrest. Products are classified also according to the method of planting. On sale you can see the capes that do not stretch, but simply placed on a chair, and if the model is calculated also on the back - the second pad is attached to the chair ties or straps. This so-called free variety. "Dense" pattern dress the entire chair from the top to the legs and cling to it. Evrochehly adjacent to the top and the bottom freer. Cases may be convenient sidushku, but there are options, and without it. Such wraps operate only decorating and protecting functions.

For office chairsFor highchairsholiday capesA complete set of covers for the kitchenOnly sidushki with rufflesIn the form of small pillows

styles covers

Classic design involves the use of expensive materials. Applied brocade, satin, silk. In the modern style appropriate synthetic fabrics. Case in eco-style is made of tough non-polluting materials. One of the sub-genres, boho, means finishing burlap. An area such as Provence, is dominated by muted colors. Cases in the style of high-tech have a simple coloring, but an interesting shape. If the room is decorated in the spirit of the English aristocracy, you should purchase a bag of expensive pearl material. Cape patchwork - a great option for independent production. Method of implementation involves creating things out of scraps and waste residue material. If the apartment is stored a lot of fragments of different tissues, it is necessary to use that symbol.

It can be:

  • old clothes;
  • unnecessary pants;
  • suspender;
  • armrests.
In the style of ProvenceThe formal stylefor holidayThe English styleIn the style of patchworkIn the classic style

The choice of fabric

The main criteria - functionality and stylistic mix. In addition, it must match the curtains and tablecloths. It is recommended to buy covers with fabrics, pleasant to the touch; they are perceived differently by people, so it requires a personal approach. It is important to pay attention to the ability of a material to maintain the high quality after washings and be resistant to contamination (depending on color). There are about 6-8 frequently used types of fabrics. Gabardine has a dense structure. Synthetic materials on all parameters worse quickly get dirty and dry. Crepe satin elastic and soft, thin enough and has luster. Lycra (supplex) elastic, looks nice, easy to care for him. Spandex is water, but perfectly "breathes", so it is durable. Brocade heavy, thick and expensive looks. Care for her hard, so it is better to use dry cleaning services.

Brocade pattern

How to take measurements from the chair

As in most cases, the first measurement is made on the longest side - the height of the chair. If necessary, the cover length is adjusted. After that is measured by the height from the floor to the seat. If the base of the chair in a continuous, without legs, the hand are measured, and if to the legs - the distances therebetween considering own thickness. Conduct necessary measurements at the widest point, usually near the floor. Many make the mistake of measuring the backrest width and height between the frame - it is necessary to know the full parameters. Measure need to seat in another way. If it is raised with respect to the frame level, the figures are taken at sidushki borders. And if at the same height - along the edges of the entire structure, but if you want to sew a cape on the seat only, it is better to measure only the soft part. Seats of this size would be enough for comfortable seating.

See also:Corner sofa in the living room interior

take measurements

Drawing and transfer the pattern on the fabric

Paper is applied to the seat of the chair, attach tailor's needle and lead round the edges. Make a margin of about one and a half centimeters for the allowance. Next, cut out detail. Pattern of the backrest is made in the same way. Then on the sheet drawn rectangle corresponding to the length of the legs and the seat width in the forehand "skirt", and thereto is added 10 cm pattern side, 5 cm and 1.5 cm below the upper seam allowance. Similarly, the drawing is held laterally. By the edge next to the outer portion of the back is added to 15 cm. To the outer part is applied a long, wide sheet. In the drawing, the rear legs of the chair is added below 5 cm, and 1.5 cm for allowance. Patterns are smoothed out, because while sewing prevent any irregularities. Further, the drawing is transferred to the material with the common thread positions. To draw on the fabric can be a pencil, a piece of soap or chalk. Plans made in the two samples.

Pattern on the fabricDrawing and PlansThe drawing for the coverDrawing descriptionDriving yardsticksPlans to Example

Fitting and advice on tailoring

When the drawings are already cooked, it remains to make the layout and learn material consumption. When sewing capes for the chair is shown an optical illusion, the alleged need a little fabric. Seams and decorative elements (ruffles, folds) "required" additional amount of material and prudence master. Newcomers need to "pilot" case. Pattern placed on a perfectly flat surface. Dimensions are verified both vertically and horizontally. Along the edges are made allowances. After removing all the shortcomings of scissors cut fabric shapes. Fitting is carried out several times. Based on its results made fit. If necessary, the workpiece rip, and again need to create a "trial" cape. The product should find the final form after will exactly match the contours of a stool. Cut to scribble on the sewing machine. We must bear in mind that the items must be placed in the direction of common thread. Direct covers will sit better if their joints equipped with zippers.

With the finished patterns can practice and make patterns, fitting and sewing slipcovers for chairs certain species.

boot fitting

Variants of covers with their own hands

It all depends on the skill and imagination. It is recommended to learn a few master classes. Color and stylistic design may not coincide with the design of the room is acceptable. The shape of the seat cover is mainly of two types: a circle and a square. Sidushka may be thin, medium or thick thicknesses. The upper part of the cover can be made similar to a thick sidushku, but with straps as fastening. If the cape is performed in the traditional manner, ie. E. chair fits on all sides, then it can be performed in many ways. One-piece cover covers the entire piece of furniture, except for the bottom - this is often done in different ways: either to the floor or slightly close the seat. Separate embodiment makes it possible to choose the length and backrest. Upper Cape is also attached strings or attachments-strings (for the back side). You can make elegant "version" with bows, ruffles, extended bottom.

Chair coversCases of shirtsSeats with rufflesCover with zipOne-piece coverCase sidushka

Cover a chair with the back of the fabric

Initially measured the length and width of the back, as well as the height of the chair. Kitchen capes recommended not to its full length, and with a margin of up to 30 cm. For room fit covers to the floor. When sewing is necessary to take into account the thickness of the back, since it may be very thin (less than 1 cm) or large (up to 6 cm). The width of the piece of fabric must be of 2-5 cm ahead of the chair. The length of the fragment is determined by the sum of two lengths of the backrest, seat length indicator and a height multiplied by two. To this number add the required margin for seams. Parting throws on the chair, adjust the length, marked space at the bolt. As a result, cape sewn so attached to the legs by means of ties or fastenings connected between the sexes-strings. In the latter case two or three such elements will suffice. They are better positioned behind the back.

Cover the back with a bowCase with flouncesFull covers for chairsCover with a skirtPlosto sit coversCase with rear button

Seats with their hands

First, prepare the pattern. Need a pencil and paper. Then, these measurements are transferred to the folded material. At each of the legs would require two straps about 10 cm long. Drawing on a similar cut sintepon. the width and length parameters thus reduced by 1 cm. Shoelace must be folded in half across the width, inside out; then stitch and turn right side out. A few large stitches sintepon need to attach to the wrong side, and ties to the corners. Now scribbling all sidushka except span length of 20 cm. Through case will be turned out on the front side. The edges of the pieces are sewn seam hiding. Further processed iron seat. If you want, in the end you need to proceed with finalizing with the help of tapes and various decorative elements. All it will take more than a few hours, and if you have experience in sewing - half an hour.

See also:Modern wall of the living room

Seats with stringsSeats on a chairIn the style of patchworkSeats with lace multicolored SeatsChair Seats

Even before the sidushka lines should lie as a "glove".

Cover on a round stool

manufacturing principle is similar to the method for tailoring capes square seats. The easiest option is to use gum. The first step is removed from the stool measurements determined diameter. The fabric is marked with an allowance of about 5 cm. The reverse side of the matter is bent by 2 cm. We need to stitch an edge of 1 cm from the turning-in - will be released as a result of a "tunnel". Eraser will be located in it. The next step - filling. The harvesting small incisions. Stuffing is distributed evenly throughout the Seats. The incisions are carefully sutured - it is done manually. Then the product scribbling on a typewriter on the perimeter. Some models are visually similar to capes lid cans. Also on the round stool will look good crocheted covers. In the process of their creation is necessary to use a variety of loops:

  1. Air.
  2. Polustolbiki.
  3. Bars, with and without sc.
Seats on a round chairRound sidushki with eyeletsSeats VelcroSidushka knitted on a round stoolSeats of clothSoft round sidushki

Knitted crocheted blankets

This product is quite easy to wash, and to tie it, do not need much experience. It does not slip on the surface and is suitable for chairs, where children sit. Among crochet techniques is to provide a column with three, two or one sc, sc without a column, without sc double, durable bar, an air loop and polustolbik. Those who have little experience, it is necessary to find out what options are very simple to learn and above all of them. It is necessary to define the scheme and knit, preventing blooming. For one capes need about 200 grams of yarn, which is about one skein. There is quite a simple scheme of creating a circular capes. First measured diameter stools. Then tally aerial loops are closed in a circle. Continue to do the ranks of the different loops. Angle aligned by skipping one of them. Upon reaching the desired size, you need to knit marginalia to be securely attached to the seat.

Knitted cover for a stoolKnitted bag with drawstringsCases with bulk flowersChair covers hookKnitted T-shirts CaseCover on a round stool hook

Cover of an old sweater

Adaptations that will be required:

  • yarn needle;
  • button;
  • yarn;
  • Sewing pins;
  • scissors;
  • pencil;
  • line;
  • sweater (preferably woolen).

First clothes washed and dried in the battery. Material "sit" sweater and reduced in size. Shroud of this wool is good to keep the shape. Next, cut two rectangles with the same width but different length (a difference of 8 to 10 cm). This reserve should be used to create the cover cover. It will be closed by means of buttons. Cut a piece in such a way to grab the bottom of the sweater gum (if any). The edges do not have to handle, and she cape will look neater. To get it maximum quality, you need to use a paper template. Carved out of the sweater folded inside out. They are aligned and secured with pins. They stitched everywhere except the top. Case turned inside out and iron with steam. At the end of the yarn around the button turns.

Cases of sweatersChair in a knitted coverFull knitted coverCovers Stool SweaterFull colored coversKnitted cover for a comfortable chair

Dress chair

It will take approximately 1 m of fabric. Sew the cape is easy, especially if you back the standard form and there is no need to fit under the belts. Enough of the two pieces of fabric and filler. Both fragments scribbling together. It is recommended to look for a waterproof fabric that is easy to clean and wash. The filler is better to take a more bland as possible. With furniture measurements are taken. Primarily determined by the length and width. If the unusual shape of the chair, with a large number of allowances, the easiest way to make the correct configuration - to attach the fabric to the chair or to the old cloak and exactly repeat its shape. The next step - the creation of the pattern and layout of the web. After this is the final stage - by the standards of sewing. Cape need from time to time apply to the chair, so that it then did not have to cut out and redone.

Cover with puzzlesglitter sidushkaStool in the form of a lambCover in the form of a catCover with applicationsCover as sarafanchik

Cover for highchair

You can make a three-layer mantle. Facepiece must be made of velor or cotton fabric, a middle - siliconized syntepon and the upper - of rigid cotton fabrics with or without synthetic her. Highchair is placed on the floor of the nonwoven fabric or tracing paper is pattern. In places where stitches are cut holes. For marking the pattern you need to put on the chair, press firmly and mark the line of the slots for the twists and belts. The first parts are cut and seal flap. Then the edge parts are joined with the main liner. Then the side flaps are carried out. On velor put finished laying down the limb. It is stitched with thread and then cut out velvet. The design is placed on the padding polyester. Cover stitched by, but left an opening for the subsequent reversing of the product.

Ready productinside paralonpattern partsfront partThe product is in the crosslinked formpocket on the back

Covers in patchwork

First it is necessary to sew pieces of cloth together. This is done randomly from scraps of different widths or regular rows of identical segments. In addition to the main part of the article, you will need a pair of scissors, needle, machine, thread, cloth inside out, cover tape, sealant. Next, you need to work on patterns. On a large sheet of paper, you can circle the seat draw allowances for seams. Suitable format A3, but also can be connected to several smaller sheets, for example by means of adhesive tape. Pattern cut out and trying on high chair. Next, the preform made three single size of the backing material of the seal and the tissue itself for the cover. The front part and the seal are formed, are marked by lines lines. All components are superimposed. Tape placed inside, and then the fabric stitch. The product is everted through the gap left. You can use the multi-colored pieces of the same fabric with uniform design or parts of different materials:

  • gabardine;
  • jeans;
  • leatherette.

See also:Console in the interior

Cover a chair in the style of patchworkFull Case of old jeansCover a chair backOn an office chair in the style of patchworkSeats on the chair of jeansCover for chair

Covers for legs

These products are designed to preserve the good condition of the flooring. In addition, the chair will not emit unpleasant sounds from moving across the floor. There are many interesting ways to perform, including cases in the form of socks, "cat feet". Most of these products knitted. Covers can be quickly done by hand, so there is no point in spending money on them. Knitting is recommended to use the thread "Darnichanka" - it is very strong. The process begins with the creation of several stitches. Around them, the bars are made without sc. In the third row we need double (two) columns, without sc in one loop and without the usual sc. In the next row are sewn same columns, but for far shackle loop. In addition they need to do sc from one loop and shackle far. In the next row - again without the usual sc. The thread is cut and fastened. And so the four cover. they further decorated as desired.

In the form of feline pawsKnitted with bowsIn the form of socksPatchwork fabricsIn a santa bootsThe color sidushki

Case for office chair

We need these tools:

  1. Scissors.
  2. Pins.
  3. A piece of chalk.
  4. Linen gum.
  5. Thread.

The basic material must be comfortable and durable: not suitable wool, very soft and "bite" of tissue. Gabardine - a good choice, it is durable and looks nice. The first step is "meter" measurements are taken the seat settings. Then they are transferred to the fabric. Drawing applied using a small piece of chalk. It leaves room for allowance of about 10 cm. Pattern cut - corners rounded to do. The edges are sewn on overlock, podgibayutsya a half centimeters and fixed pins. A sewing machine stitching is performed at 3-4 mm from the edges of the hem, pin can not be removed. Due to this, the product does not need to baste manually. The last 2-3 cm is not scribbling, leaves room for the gum. She passed on the perimeter and cut. Tails retained length 25 cm.

Cover on office desk - patchworkCover on office chairelastic coversKnitted cover on an office chairCase made of thick fabricCase cape on office chair

festive Case

The process of self-production of the festive cover is no different from creating a cape on a chair with a back. The main difference is in the cost of materials. Chairs should emphasize the festive atmosphere, so adorned with a variety of decorative elements: bows, ribbons, patterns. These wraps are used at banquets and ceremonies. The reason for creating a festive cloak may be events such as Christmas, New Year, traditional celebrations, receptions, birthdays, anniversaries. Christmas cover Christmas trees should be issued, "Santa Claus hat". It is recommended to choose the most expensive textiles in bright colors. But any more or less elegant fabric. Appropriate use of curtains and tyuley under the material for sewing. On the cover sometimes create Velcro to accommodate different applications.

In the form of caps Grandfather FrostOn New Year paper cut outsDecorated with pine cones and ribbonsBears in Christmas hatsIn the form of Santa ClausOn a chair leg

Wedding cases

The backs of these capes are elongated, square and round; It looks equally good as glossy and matt surface. As a material suitable satin crepe. The bulk of the manufacturing starts with measurements and patterns. Taking into account the characteristics of the chair model. On the sketch marked parameters, then you can start the pattern. Then all the pieces are applied to the highchair. After the first fitting is necessary to create a template. If the backrest shape is not rectangular, and round or even more complicated, you have to repeatedly adjust the fabric, trying it on the chair. To cover perfectly underlines the shape of the chair, you need to put the paper directly to him, and to celebrate the contraction and expansion in all areas. If the wizard does not have enough experience, you will need to make a few "test" products.

for newlywedsIn a lush skirtsWith bulk rosesVariants of decoration light fabricIn the style of wedding dressFor the bride and groom

conclusion

Cases do all occasions: weddings, in offices, on New Year's holidays in the high chairs. Conventional models play a functional role, are useful in everyday life. Distinguish whole, separate, universal, semi- and evrochehly. There is an ample variety of performance styles to the product combined with the general background. Chair covers are inexpensive, but the market can find simple and more expensive decorative patterns. Preference is usually given to natural materials. They are better warm, and to a lesser extent provoke sweating. Quality robe can make your own. In some cases, it is the power of the novice. Easy enough to choose execution method, make correct measurements, draw drawing, transfer it to a cloth that has been to try stuff and sew the product itself.