How to remove film from plastic windows

Protective tape covers the frames of plastic double-glazed windows in order to protect them from dust, dirt and scratches during transport and installation. Therefore, the instructions, the protective tape should be removed within 10 days after installing the plastic double-glazed windows. But you need to know how to remove the film from the plastic windows correctly, otherwise as a result you will get damaged structures that will have to be restored or reinstalled.

to the contents ↑

Why is it difficult to remove the film from the window?

The protective tape consists of two layers, which are adhered to the frame with a special solution. The inner covering is thin, very close to the plastic profile. It begins to absorb into its surface under the influence of the following factors:

• ultraviolet rays;
• use of defective adhesive when applying protective tape to the frame;
• exposure to heat enhances the absorption of the adhesive into the plastic.

Important! Before removing the film from the plastic windows, properly tune in the process, so as not to be nervous and not to hurry. Note, if you decide to remove the protective shell immediately after installation, then this procedure will not take you much time and effort. But in the event that you do not do it in time, be prepared to work for several hours.

to the contents ↑

How to remove the film from the plastic windows?

Before you begin this procedure and remove the film from the plastic windows, decide what you will do. You will need:

• building or household hair dryer;
• scraper for cleaning glass-ceramic surfaces;
• denatured alcohol;
• eraser;
• solvent for acrylic;
• white spirit;
• tool "Cosmofen";
• means "Fenosol".

Important! Do not use caustic solvents to remove this coating from the frame, as it can damage the surface of the plastic.

to the contents ↑

How to remove the film from the plastic windows?

If you have decided what to wash the windows of the film, then proceed to the action. Do the following steps.

Stage 1

At this point you will remove the adhering material:

1. Take the knife.
2. Cut to them the protective tape, acting very carefully so as not to scratch it.
3. Remove the shell from the outer and inner sides of the frame.

Stage 2

With these actions you will remove small sticky pieces of tape:

1. Take the construction hair dryer.
2. Warm up the remaining pieces of material.
3. Remove them with a special scraper to clean the glass and ceramic surfaces.

Important! Do not direct the air flow to the glass unit, but only to the frame, in order to avoid damaging the glass from the temperature difference.

Step 3

Before cleaning the plastic windows of the remaining film, prepare a soap solution and proceed as follows:

1. Take the linen cloth.
2. Dampen it in soapy water.
3. Wipe the frame.
4. Wait until it appears soap crust.
5. Remove it with a dry cloth.
6. Rub rubber seals wet, then dry, with a rag.

to the contents ↑

How to wash windows from sunscreen?

In hot and sunny summer weather, many people apply sunscreen on the glass to protect themselves from bright scorching rays. But, unfortunately, under the influence of heat and ultraviolet, the material is eaten into the surface of the window. In autumn and winter, there is no need for such an adaptation and to ensure a better warming up of the room in a natural way, there is an actual problem of how to clean the window of sunscreen. To simplify this procedure, use our tips.

Method 1

Efficiency of this method was tested by many people. To use it, do this:

1. Take methylated spirit.
2. Fill it with a spray gun.
3. Spray on the sunscreen.
4. Wait a few minutes.
5. Support the edge of the shell with a knife.
6. Remove it gradually.
7. Repeat the procedure if necessary.

Important! Remain the remaining traces of glue with the help of "Cosmofen" or "Fenosol".

Method 2

The most effective way to clean the window of a sunscreen film. For its use, do the following:

1. Take the steam generator.
2. Heat the surface of the frame with it.
3. Knife the material to be removed.
4. Open it without stopping.
5. Remove any adhesive residue from the adhesive with an acrylic solvent.

Important! Instead of a steam generator, you can apply a building or household hair dryer.

Method 3

For this method you will need an eraser for erasing a pencil and white spirit. Please note that the process will be lengthy and time consuming, but the result will be obtained qualitative. Use these tools as follows:

1. Take the school eraser.
2. Rub and remove with it sunscreen from the window.
3. Remove traces of glue from mineral spirits.

Important! If you are hesitant to apply one of the suggested options, contact the cleaning company. For these purposes they have all the necessary tools and devices - with their help they will easily solve your problem, how to remove the old film from plastic windows.

We hope that our article was useful to you and made it easier for you to remove the film. Surely, your windows shine with cleanliness and please you. But remember that this process does not cause you trouble, next time remove the protective tape immediately after installing a new plastic double-glazed window and do not forget to take care of it afterwards.