Than to wash off a mounting foam?

Foam is very popular today as a sealant, because it is able to penetrate even the smallest cracks and compacts building seams. This material has excellent heat and sound insulation properties, but if the substance hits the surrounding objects, then it is very difficult to remove it. In this article we will tell you what to wash the mounting foam from different surfaces.

to content ↑

Required tools and materials

Before selecting the solvent foam, it is necessary to find out the composition of the substance and determine the chemical agents that will help it to be completely removed from wood, metal or plastic surfaces. This building material consists of a polymer substance - polyurethane foam, which is famous for its excellent adhesion properties and increased adhesion.

In order to efficiently wash the assembly foam, you may need the following:

• Special cleaners, which are separated by the manufacturers into solvents for polymerized and still completely non-foaming foam. You can buy such a tool in every construction or hardware store.

Important! Try to buy a cleaner for cleaning contaminants and the sealant itself from one manufacturer. The fact is that each composition of polyurethane has its secret ingredient, and therefore the "native" remedy can be much more effective than other solvents.

• Brush with metal nap, scraper or knife. Such devices will help you get rid of solid pieces of hardened foam.
• Dimexide is a medical product that can be bought freely in any pharmacy. As it is not surprising, but it is an excellent solvent of mounting foam. This medical solution is quite aggressive, and therefore it should be used only in protective clothing and rubber gloves.
• Vegetable oil - this product is available in almost every kitchen and is able to wipe the mounting foam from the laminate, plastic, wood, linoleum, and even from the skin of hands.
• Direct sunlight has a destructive effect on the structure of polypropylene.

Important! It is much easier to remove the traces of fresh and not yet polymerized building material. To clean such spots, any solvent - acetone, special remover for mounting foam, White Spirit, "Cosmofen 10" and "solvent 646" is perfect.

to the contents ↑

Removing fresh sealant

If you notice the dirt in time and decided not to tighten the mounting foam from the plastic window, carefully clean the sealant with a solvent soaked cloth. This procedure will take you no more than a few minutes and almost no effort.

However, not every coating can be safely treated with solvents. In order not to damage the surface of the paint or laminate, try the action of the selected cleaner, applying it on a small, and most importantly - a barely noticeable area. Material-safe solvent does not leave whitish marks on the painted surface and does not damage the top layer of the lacquer coating.

Important! If you choose between cleaning fresh contaminants and scraping off the already polymerized foam, it is naturally better to give preference to the first option. However, if you do not notice the penetration of foam on the floor surface or if you could not find the right solvent - do not despair. Below you will find ways to wash the mounting foam , if it has already thoroughly grasped.

to Contents ↑

Removing Frozen Sealant

There are several effective ways to remove the cured and cured sealant that can be divided into two main categories:

1. Mechanical Methods.
2. Chemicals.

The most effective is to combine both of these methods to achieve the best possible result. If you want to wash off the dried foam thoroughly and without any problems, then use one of the following cleaning methods.

Method number 1 - blade and sunflower oil

To get rid of traces of sealant, you can use such simple devices as a sharp blade, for example from a razor or a clerical knife, and sunflower oil. Use these devices according to the following algorithm:

1. Using a few blades, gently cut as much pieces of frozen material as possible.

Important! Try to cut the polymerized substance under the root, because it will be easier to soften and remove its residues.

1. The remaining sealant particles on the surfaces should be gently treated with sunflower oil or with a solvent.
2. Wait 15-20 minutes - during this period of time the polymer must soften, which facilitates its easier removal.
3. Wipe the surface with a kitchen sponge, using an alternately hard and soft side.
4. After completely removing the sealant with a soap solution, wipe the surface, which will make traces of the former pollution as inconspicuous as possible.

Important! By the same principle, you can use the medical preparation "Dimexide", which is intended for the treatment of joints, skin diseases and is freely sold in any pharmacy.

Method number 2 - Blade and nazhdachka

If you need to wash the mounting foam from surfaces that will be subjected to further processing, for example painting, then only mechanical cleaning methods can be used. Excellent scraping of foam marks with a blade and sandpaper is suitable, which are used in the following way:

1. Cut the traces of the mounting foam as much as possible, which has already polymerized with the help of a blade.

1. Treat residues of dirt with sandpaper.
2. Wipe clean area with a soaked in soapy cloth solution.

Important! This method can be used to clean all surfaces that are not afraid of scratching. Most often, mechanical cleaning is used when preparing walls or floors for further staining or opening with varnish.

to the contents ↑

Than to wipe off the mounting foam from the hands?

If you are doing repair work yourself and are interested in the issue, than wiping the assembly foam from your hands, you should not forget that it is best to clean the fresh, not yet polymerized foam. For such cleaning, acetone or any other solvent is suitable.

Much more difficult to get rid of foam, if it has already dried on your hands. To solve this problem, you will have to be patient and adhere to the following recommendations:

1. Separate hands by lowering them into a hot-filled container. For the proper effect, it is necessary to hold them in water for about half an hour.
2. Apply a rich layer of nourishing cream to the skin. For this, a night cream for hands and face or ordinary oil is suitable.
3. Remove the mounting foam from your hands with a penny.

In this article we have shared with you the main ways than to wash the mounting foam from surfaces where its presence was undesirable. Sincerely we hope that now in your home there will be no undesirable consequences of the installation works and the house will be pleased with its beauty and attractiveness for a long time.