Properly performing the finishing works can save you a lot of additional hassle. To think, than to wash cement from a tile at all it is not necessary, if in advance prepare a pure sponge or a rag and a little bit of cool water. Removing contamination as they occur, regardless of whether it is cement or tile adhesive, you can prevent the formulation from drying out. It should be noted that the fixing products usually contain abrasive particles, so you need to wipe the tool very carefully, so as not to scratch the decorative layer on the surface of the tile. If at the early stage of the work the pollution was not cleared and they dried up, one can use one of the proven methods, depending on the type of composition.
Ways to remove dried
tile adhesives To clean the tile from glue that has just begun to dry up and crumbling, you need to perform two types of manipulation. First, we carry out the treatment of the problem area with a construction float( it is recommended to first glue the glue with water).Then take a soft damp sponge and in a circular motion remove the remnants of the product.
If all the dates have passed and the tile adhesive has turned into stone, you will have to resort to one of the following approaches:
- Application of the profile tool. Today, the range of such products is very wide. Here the main thing is to take care of purchasing this composition as quickly as possible and to act strictly according to the instructions.
- Vinegar. First we perform mechanical cleaning of the site with a construction float or spatula. Then we dilute a little vinegar in warm water and wipe off the leftovers of the product. The work will go faster, if previously soften the tile adhesive with a weak solution of vinegar.
- Soda. Drink plenty of water with a soft sponge, dip it into baking soda and work through the problem area. So repeat several times until you can achieve the desired result. It should be remembered that soda is soft though it is an abrasive, so we work very carefully.
Tip: One nuance should be taken into account when working - a light grout may be darkened by the use of chemicals designed to remove contaminants. Therefore, if possible, it is best to clean the tile glue, after which you can proceed to the final manipulation.
- Chlorine. We bleach the chlorine in water strictly according to the instructions, pour the ready solution into the spray gun and spray on the site with the dried glue. We wait for several minutes, until the caustic product rots the material and wipes it with a soft sponge. Be sure to rinse off the leftovers of the product from the surface. An additional advantage of this approach is the possibility of disinfection, which prevents the appearance of mold.
- Citric acid. If the tile adhesive has stained the surface in only a few places, dilute the citric acid with water with a brush. In case of extensive contamination, we use a spray gun. Be sure to wash off the composition after cleaning. Such processing guarantees not only the desired cleanliness, but also a pleasant smell in the room.
- Steam Mop. The best option for hard-to-reach places. The device will easily soften the glue( but it does not work on the cement in the right way), without damaging the surface of the tile.
Before using one of the methods described, it is recommended to check the active compound on an unnecessary piece of tile or an inconspicuous area. This will ensure that the approach is not harmful.
Rules and features of cement removal
In cases where cement is used for laying tiles, the same precautionary rules apply. But if the product has dried up, you will have to use slightly different ways to eliminate it:
- First, we simply try to wash the mass with water and a sponge, if necessary using a spatula. If this does not help, apply the profile tool, acting strictly according to the instructions. All work should be carried out in rubber gloves, tk. The aggressive components of the solutions can cause irritation and even chemical burns.
- A good effect is provided by means for cleaning the toilet bowl. We take a sponge, we moisten it in liquid or gel, we put the composition on problem areas. Leave it for 2-3 days, periodically update the product layer. Then we try to wipe the cement. In most cases, it lags behind the surface without problems, leaving no traces.
- In very difficult cases, a 5% solution of hydrochloric acid is allowed. We put it on the stains for a few minutes, then gently wash off.
- Cookery salt does a good job with such impurities. First, the cement must be moistened with plenty of water, then we apply salt on it, which should make the composition more friable. Then rub it with a stiff brush, acting very carefully and consistently. At the end of the manipulation it is possible to additionally treat the surface with a weak alkaline solution that will remove the residues of the fixative and wash it well.
- In some cases, chemicals are powerless and you have to resort to mechanical methods to solve the problem. For this purpose, you can use a chisel with a hammer. You just need to adjust to not accidentally break the tile. In addition, experienced repairers, removing cement, use a soft crust for a drill, including the machine at a minimum speed.
It is important to remember that when using chemical reagents of any degree of aggressiveness, you should carefully wash the treated area after carrying out cosmetic cleansing.
