Error e6 in the washing machine Samsung

On the body of most modern washing machines there is an information panel on which the amount of time remaining until the end of washing time and fault codes are displayed. Quite a lot of users are faced with the situation when the technical device independently informs about the problems that exist in its operability. In this article, we will tell you what the error of E6 in the Samsung washing machine shows and how it can be eliminated.

to the contents ↑

Error E6 Samsung

The built-in self-diagnosis system of a modern washing machine informs about the detected faults with the help of special designations. They are displayed on the information board and blink at intervals of once every 0.5 seconds.

If one of the days after switching on your machine has issued an error code E6, this may indicate insufficient or excessive heating of the water.

Important! Usually, this designation is displayed on the monitor 5 minutes after filling the tank with water and accompanied by a corresponding audible signal.

Error e6 in the washing machine Samsung can indicate the following problems:

1. After turning on the heater, there is an increased dynamics of water heating, as a result - the liquid temperature rises by more than 40 C in 2 minutes.
2. The water temperature has exceeded 90 ° C.
3. The water has not been heated, because its temperature index has changed by less than 2 ° C in 10 minutes of operation of the heating element.

Important! Unfortunately, in most cases the appearance of this code on the alarm monitor of your device indicates the presence of malfunctions of the technical device.

to the contents ↑

Most probable faults of the

If the Samsung washing machine diagnoses the E6 error, in most cases this may indicate the following faults of the household appliance:

1. Short circuit or burnout of the heating element led to malfunction of the heating elements. This situation is the most common and is eliminated by replacing heating equipment.
2. Malfunction of the temperature sensor, which is responsible for measuring the temperature of the water recycled into the washing machine. In most models of Samsung brand equipment, temperature sensors are built into the design of the heating element, and therefore, it may be necessary to replace the whole TEN.
3. A failure of the control board, which is usually presented as an intelligent module responsible for controlling the operating processes of the washing machine. Often there is a burnout on the relay board, which is responsible for switching on the heater. During the repair, you may need to replace the relay or additional soldering of the contact tracks.

Important! If the problem is caused by a processor burnout on the control board, then the entire module must be replaced.

1. If the error on the monitor periodically appears and disappears, it can be assumed that the wiring is damaged in the area of ​​connection of the heating element to the control module.

to the contents ↑

Useful recommendations

In some cases, the occurrence of an error E6 on a washing machine Samsung can be fixed by yourself. To do this, you need to do the following:

1. Check that the washing machine is properly connected to the mains. Make sure that the electric plug and cord of the washing machine are not damaged.

Important! For the correct operation of the household appliance, it must be connected directly to the outlet, and not through an extension cord.

1. If the error did not appear earlier, try to disconnect the styralka from the mains and re-enable it after 10-15 minutes. Probably, there was a failure in the software of the device and its reset will help to solve the problem.
2. Check the connection of the loop connecting the heater with the control module of the washing machine. Perhaps the contacts have disconnected when it is connected or they need a propayka. A similar situation occurs often after the analysis of a household appliance.

If these recommendations did not help you get rid of the problem, then you need to contact the service center for help or call a master at home.

to the contents ↑

Other popular error codes

Also, during self-diagnosis, the washing machine can display the following types of system errors on the scoreboard:

1. E1 - water set error. This code is displayed if there are problems with filling the tank of the washing machine, namely, if within 20 minutes the equipment failed to provide the proper water level in the styalka.
2. E2 - problems with draining the water. This signal notifies the user that within the allotted period of time the device failed to discharge the collected liquid.
3. E4 - overflow of the tank of the washing machine, occurs in the event of liquid entering the device after reaching the required level and is accompanied by the automatic draining.
4. E7 - faulty sensor, responsible for detecting the water level in the drum of the styralka.
5. E8 - the temperature index of the water does not correspond to the norm. It is usually characterized by excessive heating of water over a certain period of time.
6. E9 - problems associated with the depressurization of the washing machine, often accompanied by the filling of the tray with running water.

In this article we have told you about the main reasons for the appearance of the error code E6 on the information display of your Samsung washing machine, as well as possible ways to solve it. We hope that in the future the household appliance will please you with high-quality and trouble-free work.