Washing machine Zanussi - malfunctions and their elimination

One of the most sought after units of household appliances, according to all housewives, is a washing machine. The modern market offers a huge number of different models and manufacturers. However, one of the leaders is the Zanussi trademark. This is a trademark, which has proven itself with the best of luck. It produces quality models at budget prices. Today we will consider this topic: washing machine "Zanussi" - faults and their elimination, and we will tell you how to replace the bearing.

to the contents ↑

Typical breakdowns of washing machines

The most common causes of breakages Zanussi:

• clogging filter;
• breakage of the door lock;
• problems related to TEN;
• drive belt failure.

Let's take a closer look at each fault in more detail.

to the contents ↑

Filters and everything about them

In order to think less about the repair of Zanussi washing machines, it is necessary to properly operate them. The most common cause of failure of these units is a direct connection to the central water supply. Agree, the fluid that flows in our faucets is not characterized as purified water. It is tough, substandard, it can even go rusty. All this has a detrimental effect on the filter of the washing machine.

Important! When installing the device, pay attention to the fact that there are some woe-masters who specifically remove the filter of the drain valve. So you can not do it categorically. This can lead to the fact that in a short period of time the technology will become unusable and there will be nothing to do.

What is the clogging of the filter?

Filter is needed to protect internal parts from damage. This is due to the fact that the dirt that gets not only from the water pipe to the unit, but also with clothing settles on this part of the device. Unscrewing the filters, you can see there buttons, coins, hairpins, peel from the seeds of sand and a lot of dirt.

Important! In order to less clog your "helper", before washing, check all pockets of clothing and clean them of unnecessary debris.

Filters that are present in the washing machine must be periodically cleaned. This advice applies not only to the units of the Zanussi trademark, but also to all others.

Filtration instructions:

1. The water inlet pipe has an inlet filter. It must be removed and cleaned.
2. In some cases, the inlet filter is not installed. Then all the blockage can be formed on the inlet valve filter. This place is located where the water inlet hose is connected to the device. In order to clean it, you need to remove the top cover unit and unscrew the valve and filter.
3. For thorough cleaning, clean the grill and cuff. Then twist the filter together with the valve and put in place.
4. Screw in the top cover.

Important! In order to think as little as possible about the repair of washing machines Zanussi, you need to regularly clean these filters. All experts recommend doing this after two to three washings.

to the contents ↑

Breakage of the "hatch lock"

The Zanussi washing machine has malfunctions and their elimination is often associated with locking the hatch. Possible causes are:

• factory marriage;
• lock wear;
• improper handling and maintenance.

The main problem is related to the response part of this component. In the Zanussi stylalk, the plastic part, which holds the plates and serves to close the hatch, is made of poor-quality plastic and quickly breaks if the door is closed sharply and with force.

Important! The peculiarity of this problem is that it is virtually impossible to repair the hatch. Therefore, it will need to be replaced. The cost varies from 25 to 35 dollars. Due to the fact that this price is high, it is impossible to buy it for future use. Therefore, first make sure that your hatch is not working, and only then think about buying a new one.

Remove the old hatch:

1. In the first stage, open the door lid to its full potential.
2. In the right side of the window there is a hole that fixes the locking hook and two screws that must be unscrewed.
3. In the third stage, you need to carefully remove the yoke that holds the cuff. Simply put, a large rubber band is gray and is located around the window. For this you need to take a screwdriver.
4. Next you need to pull out the cuff. Do it better with your hands.
5. Insert your hand between the front of the device and the edge of the drum. Get the blocking part.
6. Visual inspection to determine the breakdown. It is very easy to do this, since the plastic part will be crushed into small parts and the plates jumped out.
7. With all the spare parts we go to the store and buy a new hatch.

Important! Due to the fact that the cost of the new hatch is very high, we strongly recommend that you use this part of the device as carefully as possible.

to the table of contents ↑

Breakage of the heating element

Among all possible reasons for the repair of washing machines Zanussi, most often - a failure of the TEN.This is due to the fact that the heating elements work with water, which contains a large number of mineral salts.

Important! The Zanussi washing machine in case of a failure of the TEN produces an error E05, which informs the owners of the malfunction. This device is located at the rear of the housing of this unit. In order to replace it or repair the breakdown with your own hands, you need to remove the back wall.

Instructions for replacing and installing a new heater:

1. The rear wall is fixed with bolts. In order to get to the TEN, it is necessary to unscrew them.
2. In the lower part of the whole case there are two contacts, from which one is sent to the right side of the wiring.
3. In the third step, you will need to check the resistance of the heating element - this is done using a multimeter. If the device shows zero, then it is worth replacing the heater.
4. There is a nut between the wiring, which should be untwisted.
5. Remove the wiring from the heater.
6. We take out the old heating element. It is not always easy to do this, as it sticks to the surface during operation. In order to remove it, you need to use grease wd-40.
7. In the place where the heater was attached, it is necessary to clean the entire surface from traces of scale and dirt. Then wipe it off with a cotton cloth.
8. We insert a new heating element, we fasten it.
9. Back install the back wall and check the operation of the heater.

Important! When buying a new heating element, give preference to only the originals that are manufactured by the manufacturer of the washing machine. If you use cheaper electric heaters, they can soon break and have a disastrous effect on the control unit. In this case, the cost of repair will increase 5-6 times.

to the contents ↑

Drive Belt and its breakdown

How do I identify a belt failure and find out that I need to repair a Zanussi washing machine? Everything is very simple! In the event of a belt failure, the device emits a loud noise, while the drum does not rotate, or vice versa - it is very easy to walk in either direction. The motor will work. However, it is worthwhile to make a more detailed diagnosis of the breakdown.

Determine the belt's fault:

1. Remove the back of the device.
2. The belt is attached in such a way that it connects the large drum in which the washing takes place, with a small motor located at the bottom of the unit:
   • . In case the belt is in place, but the device does not work, then it worsens duringand it is necessary to replace it with a new one.
   • If the belt is asleep from its location, then it must be replaced.
3. We twist the rear wall.

Important! The malfunction associated with the belt is easily eliminated, and even a teenager can do it if it acts neatly.

to Contents ↑

We independently change the bearing

Bearing replacement is often done in service centers. However, you can install a new part on the washing machine yourself. The main thing is to do all the actions very carefully.

To replace the bearing you will need:

• grease WD-40;
• bearing;
• oil seal;
• silicone sealant;
• pliers;
• pliers;
• screwdrivers;
• hexagon;
• hammer.

Important! Be sure to buy WD-40 grease. It will help you to remove all the parts that "stick" to the surfaces during operation. It is also capable of cleaning internal components from scale and dirt.

To replace the bearing and the stuffing box, you must disconnect the appliance from the mains and place it in the center of the room or garage. You need access to all the details from different sides. Lighting should be very good.

Important! In the process of disassembly, all parts must be folded in the order that they were removed. It is more convenient to photograph the disassembly process. So it will be better to collect it back.

Bearing replacement sequence:

1. Unscrew the top cover. It's very easy to do this. Unscrew the two bolts and alternately slide the component back and forth. Everything, the lid is removed.
2. We unscrew the back cover - it is fixed with six bolts. In this action there is nothing complicated.
3. Remove the drive belt that covers the pulley and drum.
4. Remove the gray rubber band - the clamp, which is located on the window of the front of the machine.
5. Unscrew the heater.
6. Remove wires from the heating element and the motor.
7. Unscrew the terminal and earth.
8. At this stage, unscrew all kinds of nipples from our drum. Do it simply, with a little effort.
9. We remove the temperature sensor. We do this carefully from two sides.
10. Shock absorbers must also be disconnected.
11. We call for help to your friend and together carefully remove the drum. It's pretty heavy.
12. Use a screwdriver to remove the motor.
13. The drum is fastened with a large number of screws, which must be unscrewed.
14. Remove the rear counterweight and detach the heater. This is necessary so that when the bearing is replaced, it is not damaged.
15. Now you can remove the stuffing box and the bearing. The first part is removed using a screwdriver, the second - a neat tapping of the hammer on the drum.
16. We replace the bearing. It is slightly heavier than the old part is removed. With the help of a wrench, you can hammer it back. Do not beat on the inside of the bearing.
17. The gland is easy to install.
18. We collect the washing machine back.

We told you about the washing machine "Zanussi", faults and repairs with your own hands. Take care of the machine carefully, keep track of all components and the service life increases several times!