Washing machine Ariston - mistake f 08

Any mechanism - both the simplest and the last generation of electronic, can sometimes fail. And if it is a complex system such as a washing machine, it is necessary to deal with possible failures very responsibly, scrupulously and carefully. We will analyze the situation if the washing machine "Ariston", error f 08 or some other programmed by this manufacturer.

to the contents ↑

The most frequent mistake is its causes and remedies

Very often, people are faced with the phenomenon that they see on their Ariston washing machine the error f 08. This combination of symbols signaling a malfunction of the technique is most common.

Reasons for its occurrence:

• The tubular electric heater relay( hereinafter referred to as "TEN"), which heats the water itself, is cut off.
• The sensor is "stuck" in the "full" position.

Here's what you need to do if you see that a similar problem has appeared:

1. First of all, we check the water sensor( in other words, pressostat).
2. Then check the heater. Usually, its connection to the electronic controller is checked. If any malfunction is revealed in the parts - the TEN is replaced completely.
3. If the TEN and the water regulator are all right, then the electric controller is replaced.

Important! In 8 out of 10 cases of error f 08 on the washing machine "Ariston" you need to change the heater.

If the failure in the SM Ariston system with the error f 08 is not eliminated, then we advise you to take your car to a master in a service center or call a specialist at home. He will certainly be able to repair your assistant so that she does not break for a long time.

to the contents ↑

Other fault codes of the Ariston washing machine - their causes and ways to get rid of the

In addition to the error f 08 in the Ariston washing machine, there are many more problems and the reasons for the malfunctioning of the machine. Let's try to understand the causes of manifestation and methods of fighting each of them.

f 01

Most often, this encoding appears if there is a short circuit of the supply circuit in conjunction with the CM drive motor.

Solution: in most cases, you need to replace the controller with the drive motor.

f 02

The response of the device can not reach the electronic controller.

Remedy: Check and replace the drive motor.

f 03

Problem with the heating sensor or, like the error in Ariston f 08, the heating element is defective.

Method of repair: replacement of the regulating element itself and, if necessary, the control module.

f 04

The problem with the pressure switch. This situation is also similar to the one that was at the beginning of the article.

Correct: you need to replace the electronic controller with the level sensor.

f 05

When the display of such a combination of symbols, a fault in the drain pump has occurred.

Necessary repair measures: replace the pump itself, pressure switch, electrical controller, possibly, and all at once).

f 06

If the Ariston eraser has issued such a combination, there is probably a sticking or other reason for the failure of certain buttons.

Method of restoring the functionality of the system: it will be necessary to replace the control panel and the electronic module for regulating the operating modes of the entire system.

f 07

With this code, the heater is not immersed in water, which means it can not heat it.

Remedy: replace the electronic controller, if necessary - also the heater( depends on the model of the control unit).

f 09

Problem with EEPROM memory.

Repair: replace the electrocontroller, the master can rewrite the scheme of nonvolatile memory.

f 10

Most likely, the level sensor does not work( there is not enough water).

Solving the problem: replacing the faulty water level control part and the electrical controller( depending on the control unit model).

f 11

With this encoding, a signal is received that the drain pump is disconnected or interrupted.

Remedy: Normally replace the drain pump and the electronic control unit.

f 12

The reason for such a set of symbols on the display is that there is no communication between the controller and the indicating module.

The way to restore the serviceability of the washing machine "Ariston" with this error: the replacement of these two parts.

f 13

If you see such symbols on the display, there is a problem with the drying mode.

Remedy: replacement of the drying control sensor and electronic module.

f 14

Drying can not start, so the washing machine "Ariston" gives an error with such symbols.

Repair is based on this principle: replace the most complex element - the control unit, and the heater, which dries.

f 15

The problem is exactly the opposite of the previous one - drying can not be turned off.

Remedy: Replace the level sensor and sometimes the connecting board.

f 17

In this case, the hatch can not close.

Method of solving the problem: replacement of the lock with the lock and the electronic control module.

18

One of the most difficult reasons is a microprocessor failure.

As a rule, only the replacement of the electric controller is possible to restore the correct operation of all equipment. Be prepared for the fact that you will have to pay a large sum of money for it, as for the services of the master yourself. It is extremely undesirable to do this on your own.

Important! Any malfunctioning of this technique, whether Ariston f 08 error or any other, described above, needs to be repaired by an experienced master.

So, in this article we have dealt with the main causes of mistakes of the washing machine "Ariston" and offered solutions to each of them. However, we do not advise you to repair the car alone, if you do not have practical experience. So you can break it completely.