How to repair the hose from the vacuum cleaner?

In the era of the 21st century, it is unlikely to find a family in whose house there is no vacuum cleaner. This irreplaceable helper is almost the main household electrical appliance in the house, and the choice of its quality, technical characteristics must be approached with skill. But how sad it is, what a famous company this vacuum cleaner would be, the weakness for the rupture of details of household appliances is present in all the untwisted brands. To our deep regret, the flexibility of hoses, even from the most durable material, is not unlimited. Having seen a gap in the bending points of the hose, we ask ourselves the question - is it possible and how to repair the hose from the vacuum cleaner? This does not mean that you need to run and buy a replacement. We'll tell you now how to fix the hose from the vacuum cleaner. Here are a few simple options for repairing a damaged hose.

to the contents ↑

How to repair the hose from the vacuum cleaner?

Depending on the location and nature of the damage, there are several ways to save your hose from the vacuum cleaner, so as not to be wasted on an unplanned purchase of expensive household appliances.

Camera repair from bicycle wheel

If the hose has been damaged in the middle, then it can be repaired using a conventional bicycle camera. To do this, perform the following sequence of actions:

1. Evaluate the degree of damage and cut off the desired length of the camera, having previously checked the rest of the part for integrity.
2. The camera must be whole and not let in air, otherwise there will be a loss of power.
3. Use the camera to connect the two ends of your hose.
4. If you find it hard to pull the camera on the hose, you can resort to soap - lubricate the ends of the corrugated tube. This will help you to eliminate damage to the damaged part without much effort and further damage.
5. After a successful connection, unscrew the ends of the chamber and wipe dry the entire surface of the corrugation.
6. These places are spread with glue "Moment" and wrap the camera back.

Important! Glued places from above can be wrapped with tape or tape - for greater reliability.

Repair with a break at the base

Depending on which hose the hose comes off from, it is necessary: ​​

• Cut the part in the torn place.
• Clean the connection from dirt and debris from the hose.
• Connect the corrugated pipe to the union. In this case, when connecting, do not use soap. Since the hose is bent in the process of work, it is possible to drop it from the nozzle.
• The corrugated tube from the vacuum cleaner has stiffeners for efficient and convenient use. Therefore, you need to screw the adhesive or tape into the choke or the base of the case.

Important! If there is a problem with the element that has broken off at both ends, then to repair the hose of the vacuum cleaner, it is necessary to disassemble the mechanism:

• Use a screwdriver to pick out the remaining fragments of the plastic sleeve into which the damaged element was inserted.
• Then paste the part with epoxy resin or sealant.
• Allow to dry for a while before use.

to the contents ↑

Cosmetic repair

It happens that due to the poor quality of the material, the hose begins to siphon in some places - cracks and small discontinuities appear in it. These unfavorable places can be corrected with the help of medical plaster or polyvinylchloride( PVC) insulation.

In order to repair the hose from the vacuum cleaner with the following means:

• Put a patch from the medical plaster on the gap with carefully wound on top of the PVC insulation. The reel is very tight, with a small margin on both sides, because the corrugated tube can let in air.
• It is possible in places where cracks appeared, neatly saw through a rigid base and wind the hose against each other. For density, rewind with tape or tape.

to the contents ↑

How to check the quality of repair equipment?

The quality of repairing the damaged part of the vacuum cleaner can be checked by checking the bicycle camera:

1. Pour into the tub, bucket, some other water tank and lowered the repaired tube.
2. Turn on the vacuum cleaner and put it on the "blowing" mode.
3. Watch where there is a leak of air.

Important! About poor repair carried out will let you know about yourself air bubbles that will come out from under the tape or tape. If you still did not succeed in the first time to achieve a positive result and the tube from the vacuum cleaner still siphonite, try once again tightly wrapped with electrical tape or tape. Only pre-wipe and dry these places from moisture.

We hope that our tips on how to repair the hose from a vacuum cleaner cheaply at home will be useful to you and you will not have to purchase new equipment at the most unexpected moment for you.