Washing machine Atlant - mistake f4

Any modern washing machine is equipped with a system of self-diagnosis and monitoring of the device. To simplify the task - both users and employees of special services, manufacturers of different equipment enter error codes - they usually have a digital-letter designation. So, if you have an Atlant washing machine - an error F4 indicates problems with a drain pump. More details about this problem and other error codes of this trademark technique you will learn from this article.

to the contents ↑

Decoding of error codes

The decoding will occur according to the following scheme:

1. Error code.
2. His transcript.
3. Variants of malfunctions.
4. Ways how to troubleshoot this malfunction.

to the contents ↑

Sel

If the machine that does not have a display does not light, this indicates that the interface module has failed. The Sel code on the typewriter with the display will also testify to this.

Most likely, there was a breakdown of the potentiometer, which is needed in order to select programs. Replace the interface module.

to the contents ↑

None

The display shows the code None. If there is no display, absolutely all indicators are lit. This code means that the amount of foam that was produced is excessive.

What could lead to this problem:

• Too much powder was used during washing. Just limit yourself to less powder.
• The specified mode is incorrect. That is, the regime that foresees the flooding of a large amount of water. Choose a washing mode that is specifically designed for a particular type of fabric.
• Used such a powder or any other detergent that is not suitable for washing in the machine. Use only those powders and products that are designed to be washed with this machine.

to the contents ↑

Display F2

If there is no display, the third diode will light up. Means such an error code for the washing machine "Atlant", that a temperature sensor has failed:

• Probably a problem with the contacts and the wiring of the temperature sensor or the module. Make sure that the contacts and wires are fully functional.
• The temperature sensor has deteriorated. Replace the heating element - heater.
• The control module went out of action. Replace this faulty module.

to the contents ↑

The panel lights up the F3

The older model shows the 4th and 3rd indicators. The heating element of your washing machine is out of order. This is possible for the following reasons:

• The heating element has broken. Replace the heating element.
• Broken wiring or the same contacts. Make sure that the wires and pins are in good condition.
• The control module is out of order. Replace the module.

to the contents ↑

On the display F4

Alternative, if the washing machine "Atlas" has issued an error f4 - the diode number 2 is illuminated. Damage to the drain pump, it's a pump.

Reasons:

• The drain hose is clogged or hammered. Straighten the hose, locate and remove the blockage.
• Incorrect hose installation. Reinstall the hose in the manner required by the instruction.
• If a foreign object enters the pump, its impellers are stuck. Eliminate the object, check the impeller for rotation.
• The drain pump is broken. Replace the broken pump.
• The ball in the fuse coupler fuse. Drain water from the washing machine with a tube, and then change the coupling.
• Clog of the drain coupling. Perform the cleaning.
• With wiring and problem contacts. Check them for service.
• The electronics module has become unusable. Replace the electronics module.

to the contents ↑

The display shows F5

The 2nd and 4th indicators light up on the no-display machine. Damage to the valve of the bay.

Causes:

• The water inlet hose filter is clogged. Clean the filter.
• The filler hose clogged or jammed. Unscrew the hose from the machine, start the water for inspection. If necessary, clean the hose.
• There is no water in the water supply, the water supply in the faucet is closed or the flood valve has broken. Make sure that your faucet is open. Make sure that the water in the water supply is not turned off. If necessary, replace the valve.
• Chains were interrupted between the fill valve and the control module. Use a tester to check the presence or absence of an open.
• Faulty contact of the priming valve. Check the contacts and make sure they are in working order.
• Breakdown of the control module. Replace it with a new one.

to the contents ↑

Control panel issued F6

If there is no display, the 2nd and 3rd indicators will light up. The problem with the electric motor relay.

The reason is that the stator winding has overheated. The contacts that are responsible for the thermal safety of the engine are disconnected. Make a replacement for the engine of the unit.

to the contents ↑

Display F7

In the older model of the washing machine "Atlant", 2, 3, and 4 indicators are lit. The problem lies in the power supply.

Causes:

• Interference filter failure. In this case, you just need to change it.
• The mains voltage does not correspond to the required voltage - it can be voltage more or less. Check the network with a tester.
• The control module has broken. Replace it.

to the contents ↑

Error code F8

Alternative indicator No. 1 is lit. Too much water in the tank.

Causes:

• The pressure switch has broken. Replace it.
• The priming valve has stalled. Replace the old valve.
• Problems with contacts or wiring of the pressure switch, as well as the control module. Check up these wires and contacts on presence of breakages.
• Tightness of the container is broken. Check your tank.
• The broken control module broke. Replace it with one that will be operable.

to the contents ↑

Lock F9

The indicators under No. 1 and No. 4 are lit. Such error codes of the washing machine "Atlant" mean that the problems lie in the tachometer engine.

Causes:

• A fault in the contacts and wires of the control module or the electric motor. Make sure that there are no faults or not, by checking all the terminals and wires.
• Broken tachogenerator or engine. Replace the motor.

to the contents ↑

On the display F10

If your machine without display indicators No. 1 and No. 3 are lit. Broken UBL - locking doors.

Possible problems with such error code of the washing machine "Atlant":

• A malfunction with a lock. Replace it with a brand new one.
• The control module has broken. Replace it.

to the contents ↑

The message "door"

The 1st, 3rd, 4th indicator lights up. Most likely the lock broke.

What to do:

• The lock contact is missing. Make sure that all wires are connected correctly and cutouts are excluded.
• The hatch is not tight enough. Close the hatch again.
• The lock or the door jumped. Correct the hatch or lock.
• The chain between the control module and the manhole lock was broken. Use the tester to test the circuit.
• Problems with the lock connector. Check if the wires were connected correctly and in general.

to the contents ↑

Display F12

The 1st and 2nd indicators should light. It is quite possible the breakdown of the engine's triathode.

What became the cause:

• The engine of the car broke. Replace it.
• The motor winding was cut off. Carry out the replacement of the motor.
• Contact missing. Check the condition of the connector and wires.

to the contents ↑

Display F13

In this case, the 1st, 2nd, 4th indicators will be lit. The problem with this error code is the washing machine "Atlant", that there is no single-valued reason for the failure.

Usually - this is a problem with the contacts or with the wiring. Check the wires and contacts.

to the contents ↑

The 1st and 2nd indicators will start emitting on the display of the F14

.There was a failure in the program.

The program failed because of incorrect programming of the electronics module. Urgent replacement of this module.

to the contents ↑

Display F15

This error code for the washing machine "Atlant" indicates that a water leak has been detected. The reasons for this phenomenon:

• The tank was depressurized. Replace it.
• Flows through the locked door. Replace the manhole cuff.
• The sealing of the drain hose, drain coupling, nozzles is broken. Try to determine the location of the leak, and then eliminate it. Make sure that the yokes tightly fixed the nozzles, and the pipes and drain hose are in integrity and safety.

In this article we have made an overview of the most common error codes for washing machines Atlant - with and without display, so you can independently figure out what causes the breakdown. Remember that the replacement of the engine is a very expensive pleasure, the repair of the electronic control card is carried out only by masters of special qualification. But to deal with the drain pump, pump, hatch, for example, if the washing machine "Atlant" has issued an error F4 or the code Door, you probably will be able to independently.