The best hacksaw according to buyers' feedbacks

What is the difference between a good hacksaw and a bad hacksaw? Perhaps, the metal from which its main part is made. A bad saw has little teeth. And even if they seem sharp, then they cease to be so after one or two works. A good hacksaw has such a steel, which does not rust, and its sharpness holds for a long time. In this material, we tried to talk about the best hacksaw - to these tools there are not any serious claims. And it will only deal with manual models, as the "Viborovest" already told about the elektronozhovkas.

Hand hacksaw of which company to choose

Many companies are engaged in the production of hand tools. There must be at least a couple of such enterprises in each country. And only a few companies were able to reach the world level. It can not be said that they have won success due to the quality of their products. No, everything depended on luck and marketing. Therefore, one should not think that high-quality hack saws are produced only by companies whose name is on hearing. However, let's not seriously develop this topic.

If you do not trust little-known firms, then pay attention to the products under the following brands:

1. ENCOR

2. IZHSTAL

3. VIRA

4. STANLEY

5. FIT

Usually products under these trademarks are notcause any complaints. And do not be scared that some of these brands are domestic.

The best hacksaw for wood

ENKOR 9858

Hacksaw belonging to the "Wolf" series, as evidenced by the inscription on its working part. The tool has a plastic handle on which there is a rubber lining. Hacksaw is designed for sawing wood. To do this, it is equipped with a set of teeth 4.5 mm high. Each tooth is sharpened at three angles, which greatly accelerates the sawing.

The length of the tool can be called slightly shorter - it is 400 mm. The handle is screwed onto three screws, which makes it possible not to doubt its reliability. The cloth was made of high-strength steel. A plastic cover is supplied with the tool, which performs a protective role during transportation.

Advantages:

• Hooked at three corners;
• The handle is securely fastened to the fabric;
• The blade is polished;
• On the handle there is a rubber lining;
• Supplied with plastic sheath;
• Teeth are hardened;
• Low price.

Disadvantages:

• None.

ENKOR 9857

Another joiner's hacksaw from the well-known Russian manufacturer. But she belongs to the family "Beaver" - the corresponding inscription can be found again on the canvas. As in the case of "The She-wolf", the fastening system to the handle consists of three screws. Also there is a rubber pad, which reduces the load on the palm. At rest, the hacksaw must be in the plastic case supplied.

The blade of this product is made of polished and high-strength steel. Teeth are universal - they are sharpened only at two angles. As for the handle, it allows you to delineate angles of 45 ° and 90 ° without using any auxiliary tools. A distinctive feature of the ENKOR 9857 hacksaw is the length increased to 500 mm.

Advantages:

• Diluted and very sharp teeth;
• There is a plastic case;
• Low cost;
• Increased to 50 cm in length;
• The handle is securely attached to the fabric;
• There is a rubber lining.

Disadvantages:

• Teeth are not hardened;
• Teeth are sharpened only on two sides.

IZHSTAL 030108-050

The 500 mm hacksaw made in Izhevsk is distinguished by its low cost. This is one of the cheapest hacksaws among those that have a two-sided grinding of teeth. However, you will have to accept that the teeth are not diluted here, which will definitely affect the speed of sawing wood. If you do this very rarely, the hacksaw IZHSTAL 030108-050 will be a profitable investment. If you saw something regularly, it is better to consider the tool more expensively.

The handle in this model is made of plastic in orange. It is fixed to the canvas with the help of three bolts. As for the teeth, their pitch is 6.5 mm. The size of the teeth can be called average. Unfortunately, the handle does not have any additional functions - you can not draw corners with it.

Advantages:

• Reliable attachment of the handle to the canvas;
• There is a rubberized part;
• Very low price tag;
• 500 mm length.

Disadvantages:

• Only two-sided sharpening;
• The tooth is straight;
• Teeth are not hardened.

The best hacksaws for aerated concrete

ENKOR 19183

Hacksaw from the company ENCOR, belonging to the family "Fox".From other tools is distinguished by a small tooth, the height of which does not exceed 2.5 mm. The teeth are hardened, which indicates their long life. The manufacturer recommends using saws to saw products made of aerated concrete. The length of this model is 500 mm - an ideal parameter.

As in the case of the hacks mentioned above, the canvas is attached to the handle with three screws. This is the most reliable system - it will not be possible to break the tool by accident. The handle was made of yellow plastic. Most of it is covered with rubber, thanks to which you can work with this saw without gloves.

Advantages:

• The handle has a rubber coating;
• Hardened teeth;
• Copes well with aerated concrete;
• Optimum length;
• The handle is securely attached to the canvas;
• We used high-quality steel.

Disadvantages:

• High cost.

ENCOR 9847

This saw is even very different from its competitors. As a web, a carbide insert is used here. It is on it is located the teeth, which are very large. Such a hacksaw turned out to be heavier than a steel analog. But it copes without any problems with sawing aerated concrete and products from other abrasive materials.

On the handle of the hacksaw from the series "Raven" you can not say something special. It was created from the plastic of yellow color, which is customary for products from ENCOR.A part of the handle is covered with a rubber lining, which makes it possible to work without gloves. It is attached to the canvas using a traditional system consisting of three screws.

Pluses:

• There is a rubber lining;
• Reliable attachment of the blade to the handle;
• The blade was made of carbide;
• Serves very long;
• Excellent coping with sawing abrasive materials.

Disadvantages:

• Many people will find the hacksaw very expensive.

The best hacksaw for metal

VIRA 801010

A very simple hacksaw, serving for sawing metal. Her handle was created from two components. The main one is plastic. The second component is a rubber lining, thanks to which the palms almost do not get tired, just as they do not have corns. As for the remaining parts of the hacksaw, they are made of tool steel. The canvas here uses a standard - 300 mm long, it can always be replaced.

Pluses:

• Traditional canvas, sold in every store;
• On the handle there is a rubber lining;
• Easy blade replacement;
• Secure grip of the handle to the main part;
• Pocket for almost everyone.

Disadvantages:

• Someone will find the complete canvas not sharp enough.

YATO YT-3161

Cute externally locksmith's hacksaw. Uses a traditional 300 mm canvas. The supplied cloth is of the 24TPI type. It should be noted very easy to replace it - no auxiliary tools are required. Also, buyers praise this product for the ergonomic handle. It is equipped with a large layer of rubber, so that the palm remains in order even after several hours of work.

Pluses:

• On the handle is a pad of quality rubber;
• Robust construction;
• Quick change of cloth;
• The supplied cloth is of high quality;
• Optimal for working with metal length.

Disadvantages:

• Cost - obviously overstated.

STANLEY Mini 0-20-807

Sometimes a worker needs to cut a metal part in a hard-to-reach place. Or he needs to cut a very small piece of metal. For all these purposes, a traditional metal hacksaw does not fit - you need something smaller. This is something like the STANLEY Mini 0-20-807.This hacksaw turned out to be very miniature. In fact, it is made in the form of an ordinary knife, but with some reinforcement - otherwise the design would quickly fall apart.

The product uses a 300 mm canvas, 50 mm of which are hidden in the handle. The handle is single-element - it was created from plastic by the method of injection molding. The length of the canvas is adjustable. All this allows you to saw "flush" with the surface. It is interesting that theoretically the hacksaw allows the use of even broken cloths.

Advantages:

• Unique miniature design;
• Broken canvases may be inserted;
• It is possible to work in cramped conditions;
• Minimum cost;
• Standard fabrics are used;
• Difficult to break.

Disadvantages:

• Handle is not rubberized;
• Not suitable for cutting large quantities of metal.

Best gypsum plasterboard saw

STANLEY Fatmax 0-20-556

Very small hacksaw. Most of all, it resembles a private knife. The difference lies only in the presence of teeth. The length of the tool is 302 mm. The handle is rubberized, so that the palm on it practically does not slip. In general, this is the best option for processing drywall - such a hacksaw leaves a clean cut after itself.

Pluses:

• Cloth is made of durable metal;
• Very good cut drywall;
• Rubberized handle;
• High reliability;
• Minimum weight;
• Compact size.

Disadvantages:

• The price is difficult to call low.

Which hand hacksaw to buy

1. If you are engaged in carpentry, then you should consider buying ENCOR 9858. This hacksaw has hardened teeth, sharpened on three sides. The cloth is screwed to the handle with three screws - this design is the most reliable.

2. The ENKOR 9857 is a bit simpler than the saw. This tool also does a good job with any sorts of wood, but the process in this case will go slower, since the teeth are sharpened only on two sides. But this hacksaw is 100 mm longer.

3. Even more cheap product is IZHSTAL 030108-050.This is the best option for those who need a hacksaw once a year or even less often. Then you definitely will not regret your savings.

4. For sawing aerated concrete the ENKOR 19183 hacks should be used. Its cost is quite high, but it does not have any serious drawbacks. In this case, a small tooth is used, which should positively affect the accuracy of the work.

5. Even better with aerocrete is ENCOR 9847. However, this hacksaw due to the materials used here is much more expensive. It should be bought only in case of subsequent regular use of the instrument.

6. For work with metal, you can buy VIRA 801010 and YATO YT-3161.These hacksaws are approximately the same. They have rubber inserts, their cloths are easy to change, and the cost of tools does not cause fright( although the latter is the latter fact to a lesser extent).

7. If there is not enough space for sawing the metal, STANLEY Mini 0-20-807 will come to the rescue. This is a miniature tool that is no bigger than any knife. In this case, they are supported by standard 300 mm canvases.

8. If you regularly work with gypsum boards, we recommend that you purchase STANLEY Fatmax 0-20-556.It is a narrow tool with large enough teeth, which saws with a clean cut.