Loose nuts are not uncommon. There are quite a few ways to remove them, from WD-40 to cutting grinder. But sometimes it happens that none of the options works, and it is impossible to crawl into a hard-to-reach place of the same angle grinder. What should you do in such a situation? Can help out here ordinary screwdriver, of course, with a special attachment. Let's try to figure out what needs to be put in a bag with a tool so as not to find ourselves in a hopeless situation.
Read in the article
- 1 When is the use of a screwdriver justified
- 2 When you may need such equipment
- 3 The nuances of using cutting discs when working with a screwdriver
- 4 Using a screwdriver when trimming studs and bolts
- 4.1 Preparing bolts for cutting
- 4.2 Cutting a bolt with a screwdriver
- 5 Surprising next: what else can you use a screwdriver for
- 6 Final part
When is the use of a screwdriver justified
It should be immediately noted that it is better if among the tool there is a device specially designed for working in hard-to-reach places. We are talking about an engraver, or as it is also called a dremel. This device is equipped with a flexible shaft and a huge number of different discs and attachments. But not everyone has such a tool, which means that sometimes the use of a screwdriver is justified. However, in order to use it for such purposes, you need to purchase a special attachment that will allow you to install a cutting disc on the tool. But first things first.
When you may need such equipment
Usually, a stuck nut is soaked and torn off, or, in the most difficult situations, cut off with an angle grinder. However, the following may turn out, for example. Many years ago, the mixer installed on a ceramic sink needs to be removed. But during installation, the gasket rose unevenly and water leaked along the thread during operation. In this case, it is unlikely that it will be possible to unscrew the mixer fastening nut without damaging the ceramics. Also, you will not be able to use a grinder. Then, in the absence of an engraver, you will have to use a screwdriver.
The nuances of using cutting discs when working with a screwdriver
The rotations of the screwdriver are much lower than that of angle grinder, which means that you should not be afraid that the disk will break. Another thing is that it is precisely the low speed that contributes to the rapid abrasion of the disc. In addition, it is not always possible to crawl into hard-to-reach places with a large circle, which means that it is better to have a small supply of "remnants" with you.
When cutting metal with a screwdriver, do not neglect personal protective equipment such as glasses. The fact is that it is precisely because of the low speed and rapid abrasion of the cutting wheel that a huge amount of abrasive dust will fly in the air. But she is not the most dangerous. Much more serious will be the consequences if a particle of wire enters the eye, with which the cutting disc is reinforced.
Using a screwdriver when trimming studs and bolts
If a situation arises when it is necessary to quickly cut off a few bolts, and the grinder is not at hand, the screwdriver can provide an invaluable service. Of course, you can use a hacksaw for metal, but this work will take a very long time. It is best to combine the two, and we will now look at how to do that.
Preparing bolts for cutting
To begin with, mark the required length of the bolt with a marker. Next, two nuts are screwed onto the bolt so that they are on the side of the head from the risks. In this case, one of them is set flush with the risk, and the second so that it acts as a locknut. Then the bolt is clamped into the screwdriver chuck by the thread, which is superfluous.
Cutting a bolt with a screwdriver
A hacksaw for metal is used as a cutting blade. It is held in place (it is good if it is possible to fix the canvas). The bolt rotating with a screwdriver is leaned against the canvas and cut off rather quickly. In this case, the nuts play another important role. After cutting, slight damage to the thread is inevitable. So, when you unscrew the nut, it is restored.
Surprising next: what else can you use a screwdriver for
The ingenuity of our people knows no bounds. And if somewhere abroad a screwdriver is used only for its intended purpose, then our people are clearly not satisfied with this state of affairs. We bring to your attention a selection of interesting ways to use this power tool, which could only be thought of in Russia, and, perhaps, in China (up to some).
1 out of 7
Note to the electrician: with the help of a special bit, you can very quickly make tight and high-quality twists
If you buy a Chinese nozzle, the screwdriver turns into scissors for metal
How about an engine for a rubber rowing boat? Seems not bad
If desired, you can even make a vacuum cleaner from a screwdriver
For lovers of ice fishing, such a drill will be very useful.
And even in cooking, the screwdriver found its application.
And this is generally a masterpiece: by combining a screwdriver and a door closer, you can get an electric door drive
Well, you can not even talk about various electric bicycles, children's ATVs and scooters driven by a screwdriver engine.
Final part
The screwdriver can really be considered a versatile tool. Of course, other equipment is also undergoing alterations, but the plus of this power tool is its light weight and compact size. In addition, today such devices are becoming more powerful, the voltage given out by their batteries is getting higher. And it is not known what else our craftsmen will think of in the near future. In the meantime, we can say that in the presence of various attachments and accessories, a screwdriver is quite capable of replacing almost any power tool in the arsenal of a home craftsman.
We hope that the information presented by us was interesting and useful to the dear reader. HouseChief editors will be happy to answer your questions, if any, have arisen in the process of reading the article. You just need to summarize them in the discussions below. There you can also comment on what you have read, express your personal opinion or share your use of the screwdriver, if one was not included in our review.
Did you like the article? Then do not forget to rate what you read. Your feedback is extremely important to us. And finally, as has already happened, we offer you a short video for viewing, which will help to more fully reveal today's topic. Take care of yourself, your loved ones and be healthy!
