🏡 cover the well with your hands: the most popular versions

Once at the site appeared well, it's time to think about his accomplishment. This will not only give the structure a beautiful appearance, but will close against the water surface debris. We offer to find out how to make the cover for the pit with their hands, which are needed for this material and tools. Properly manufactured product will last long enough.

How to make your own hands the wooden cover for the well, two popular options

The tree is traditionally used for the manufacture of the well cover. This material is available and can be easily processed by hand. But such a design of the cover may vary. We offer to meet the available options.

Cover-shield

Rather simple embodiment, wherein ease of execution. Make the size of the well. Cover-shield is pretty simple to assemble. It serves as a relatively short time. It needs constant treatment. When properly matched paint and varnish materials will last for more than 5 years.

Materials and tools

Preferably use for the manufacture of alder, lime, oak, birch. Board size may be any, but is preferably the panel 15 cm wide and 20 mm thick. For compounds boards require bars. Of the tools necessary to prepare:

• saw or jigsaw;
• a hammer or screwdriver. Selection depends on the fasteners: nails or screws;
• crowbar;
• loop;
• pencil;
• building level suitable size;
• measuring tool

Step by step instructions on making

The cover-shield of the planks is manufactured as follows.

Illustration	Description of the action
	Originally produced from planks and bars strays shield. To do this, the board is sorted and placed as close as possible to each other. It should achieve the minimum clearance. The width of the formed board should be consistent with the external dimensions of the well and the dimensions of shaft
	On the back of the boards are nailed to the bars. They have laid perpendicular to the panels. To ensure sufficient levels of rigidity in the center of the board is attached
	With the desired level outline circle diameter. To do this, one end is fixed, and the second begins to shift along the formed sheet, prorisovyvaya circle the correct diameter
	Using the jigsaw is made by cutting contoured line
	With the selected edges with a jigsaw cut door, through which water will accrue. Originally worth doing cuts only on two sides.
	After installation of the door hinge is completely separated from the ground shield.
	To increase the service life, the structure is treated with a preservative. Thereafter, the water pump can be dialed either via the bucket.

Attention! If the diameter of the well is relatively small, it is possible to abandon the manufacture of doors, making the cover-panel removable.

Cover in the form of a house with door

Cover-boards are of limited use. The most popular cover in the shape of houses. We offer to find out how to make a similar design with their own hands.

Materials and tools

For the manufacture of the house need a standard set of tools. You should also prepare:

• timber 100 × 100 mm²;
• board 100 × 30 mm or water-resistant plywood sheathing for the house;
• timber 50 × 50 mm²;
• beam diameter suitable for forming drum.

Step by step instructions on making

The manufacturing process of the cover to form a well in the cabin can vary. Some collect design directly at the installation site. This may not be the best way impact on product appearance. To avoid typical mistakes, it is necessary first to make the basic elements and then produce their assembly at the installation site.

Completing elements

Before proceeding to the assembly design, it is worth to prepare the main elements of the components:

Illustration	appointment
	Quadrangular base frame. Its size should be matched to the dimensions of the well. The outer edge is more internal - less
	Support legs for drum. Their height should match the height of the house, and the angle formed on the one hand - with the angle formed at the attachment of the roof. At the desired height bore holes under the handle of the drum
	Drum. hewn logs should be used for its production. Before the start of the drum assembly must be connected to a handle

Attention! The size of the board are cut by a house which is sheathed.

construction assembly

construction assembly involves the installation quadrangular frame on the well. Then there was a support attached to the drum and the drum itself is mounted. It is the frame. Check the efficiency of the design. The drum must spin freely when turning the knob. If there are difficulties, its spatial position is adjusted.

On the frame is mounted prepared plating material. Cut a hole for the door. The latter is hinged by hinges. The design is painted in the color selected for protection against external adverse factors.

We also offer watch a video detailing the cover of the manufacturing process on the well:

Cover well with your hands from metal and PCB

Time service wooden structure is substantially limited, even with timely maintenance. In this situation, it is worth paying attention to the alternative options that would provide a solid and reliable lid on well from metal and PCB.

Materials and tools

To work required:

• metal rectangular or corner;
• textolite sheets of suitable size;
• electrodes;
• welding machine;
• Bulgarian.

Step by step instructions on making

To assemble the cover of the well, you must first prepare thoroughly. To do this, the place of installation bring the necessary materials, tools and equipment, and then start to work.

Completing elements

As component elements in this case are lengths of sheet steel and PCB. Before beginning installation, cut them to size. In metal intended to form the frame, the ends are cut at an angle of 45º. This will get in the place of the elements connected by a straight angle.

With prepared corners or square tube formed rugged frame. Previously prepared elements are welded together. Seams are formed on both sides to provide sufficient strength, then are stripped convenient way. It is desirable for this purpose to use a grinder.

Rectangular profile pipe welded together to produce the movable cover. The length of the pipes should be at least 1 cm over the length for ease of opening the door during operation.

Attention! Prepared elements amplified by a pipe welded diagonally.

construction assembly

In the process of assembling the frame is connected to the access door. Cut in size textolite plate screwed to the chassis with screws. To eliminate the freezing of the door in the winter, the contour paste insulation materials: foam or polystyrene.

Master-class on making of concrete cover

If you need a concrete cover for the well, do not despair. It also can be made with your own hands. The process is quite laborious and lengthy. We offer to get acquainted with detailed instructions to help cope with the task.

Materials and tools

For the manufacture of concrete cover for the well will need:

• concrete mortar;
• fittings;
• bricks;
• evroruberoid;
• assembling mixer;
• Master OK.

Step by step instructions on making

Process serial conversion concrete mortar into a finished product includes a plurality of different sub-steps. Offer to get acquainted with the list of actions that need to commit to at the well appeared sturdy and reliable design of concrete.

Completing elements

To prepare for the production of concrete cover, it is necessary to:

• cut in the size of the valve and form it can help frame the contours of which will be fully repeated silhouette of the house next to the well;
• prepare the formwork. If there is none, you should create it using bricks;
• to prepare a concrete mix, mixing the components in the desired percentage.

construction assembly

To make the cover of concrete, it is necessary to:

Illustration	Description of the action
	Forming formwork using bricks, arranging them in the correct sequence. To exclude leakage of concrete outside the inner walls obkladyvayut evroruberoida. Fill the prepared design of concrete and carefully tamped
	We laid on top of the previously welded fittings. Dent it in concrete. Give the stand for 2-3 days
	Fill the top layer of concrete. Give the product to dry completely
	Set the finished end of the concrete pit

Share in the comments, some lodge for well do you prefer? How satisfied are you in such a constructive execution?