Laying laminate own hands: step by step video instructions and tips

Do you want to refresh floor in my home? You have chosen a laminate for this purpose? If so, then with his hands laying laminate (step by step video instruction at the end), which is described in this article is for you. After reading it, you can make sure that it is very simple. After covering can be laid on their own, without resorting to costly professional. Skills in construction work, of course, not prevent, but without them, with some effort, you are sure to do the task.

Which laminate flooring to choose?

It all depends on the location in which you want to lay this type of coverage. To choose the type of material affects:

• relative humidity in room;
• The load on the floor;
• The frequency of the mechanical action of heavy objects on the surface of the deck;
• The presence of water tanks located on the floor;
• The impact of thermal radiation that may come from the heaters;
• Color spectrum interior.

For sale is a huge laminate selection with varying degrees of protection. You remain determined by the above listed indicators of what material to buy, thin or thick, water-resistant or not resistant or home, light-colored or dark. Next, you will learn how to correctly and without difficulty to lay laminate own hands with good examples on video.

How to put a laminate floor with their hands with an explanation and a video demonstration

The first is to make sure that the floor has been prepared for installation. It should be flat and smooth. Remove any unevenness can be by any means at hand, and to carry out major works need some tools. Here is a list of them:

• fretsaw or hacksaw wood;
• A hammer, a chisel, a hatchet;
• Level, monofilament, tape, pencil;
• Stationery knife, tape.

Nuances when mounting the laminate on different surfaces

Depending on the type of subfloor principle of stacking the laminate differs. So, if the floor concreteThen it first spreads heater polystyrene or foam because such a floor will be given to cold laminate. If the floor is wooden, it is necessary to process antiseptic and eliminate all moving area (if any), and then you can proceed to the installation of the laminate. When the material is spread on the old linoleum, You need to put it over a special substrate denser structure than the standard.

A calculator for calculating the required number of laminate

Simple laying laminate by hand. Step by step video instruction + a detailed description

You can study the performance of the installation procedure from a video laminate flooring with your own hands and use the instructions below.

Step-by-step instruction

Step One

First priority should be given to marking the floor along its entire length and width. Use of the laminate strip. And when you record the layout, leave a small space from the wall. Depending on the characteristics of the coating and the room in which it is positioned, the gap should not be less than 8 mm and not more than 12.

Self-stacking feature is based on the fact that each individual laminate layer attached to another via grooves. Part of this is reminiscent of the assembly of mosaic or puzzle. If you attach the laminate items using assembly adhesive, then be prepared for the fact that after some time, it will perform a surplus on the floor. This may happen because the temperature drop which usually occurs in the room.

Step two

If during installation, you notice any discrepancies or irregularities, do not be discouraged, but rather pay attention to the tips that will be described below.

Tip! At the location where the laminate layers are connected with each other at two different ends of the hammer on one nail, and then pull the fishing line or a thin thread and strengthened by these most nails. In this way you can give yourself the confidence that the laminate lies so exactly as you would wish.

step three

Immediately after you have prepared the floor, designated markup, and picked up the dates of your layers, they must be removed. In addition, the entire surface of a film to be distributed, the main purpose of which will be waterproofing. Please note that the professionals are advised to lay flooring in stages, to the extent that, as you will be laid directly flooring itself.

the fourth stage

At the end of the waterproofing laying flooring, it is necessary to take care of the cushion flooring. This layer will also serve soundproofing and strength. If we talk about what material should consist of a cover, this may be the most common polyethylene or felt. Just like the previous one, it is desirable to stack the layer gradually rather than all at once. In this way you can put it smoothly and safely.

Related article:

What a substrate under a laminate better. Choosing a material like laminate, do not forget about quality substrate from which the beneficial properties of the floor covering depends largely. In our review, we find out what the substrate under a laminate better and how to choose the right.

stage five

At that moment, when you're ready to begin immediately to lay laminate own, make sure that the glue that you want to use, was the desired consistency. Then, enter it in a special, assembling the syringe and spread evenly over the end side of the plate. Try to calculate the dosage of the adhesive so that the groove laminate he filled completely, but at the same time did not come out of his face. In case if at the junction of the two plates, the adhesive still perform, use a spatula to remove it from the surface.

Step six

Now you need to go back to the time slot you laminate panels filled with glue. Give it a little bit dry, and then type in the tongue groove, which is located on the edge of the other plate. Further, the adhesive filling the next floor covering plate and the groove in it, respectively, also enter the groove. Continue in this way, as long as it laid the first row of flooring.

seventh stage

After all of the above processes will be completed and completed successfully, it is necessary to pay special attention to this step. Because on it, your main task will be accurate measurement interval between the wall-end final formation. This can be achieved in the following way: Full-layer overlaps the previous so that the extreme spike of the sheet was docked with the adjacent wall.

eighth stage

If you have followed all of the above tips, then by the time you come to the eighth stage, you have laid the first row of flooring. After that, you should immediately take the alignment of its individual layers. At an earlier stage you've already pulled a strong thread or fishing line and now with its help will be able to carry out this procedure. On the part determine how the plates are rejected and if the slope is large enough, use wedges to return laminate plate in place along the taut fishing line. In addition, you can adjust the plate in relation to one party or another, you can also drive these very wedges layer below or on the contrary, to raise it.

Note! It shows construction practice and experience in many apartments, especially the old-fashioned, often laying laminate necessarily carried out next to the pipes or batteries. To work around this difficult situation can be very simple without making any extra effort. It is necessary only to cut the laminate formation, which will adhere to the pipe piece commensurate with a protrusion on the battery cover. If you cut off a piece of considerably less than required, then this can be easily corrected on the spot. And if you cut a recess was over, then fill the space you have available mounting adhesive. If your light-colored laminate flooring, to fill the space, you can use a mixture of glue and sawdust. Thus, the extra space will be less noticeable.

the ninth stage

This stage can be called a break or rest. Immediately after the flooring is smooth, all the flaws and errors have been rectified and corrected, you need to give the floor to "rest." At this time, the glue dries and solidifies, the plates securely thereto affixed to each other and with the walls of the room. It is enough to be a break of one hour long.

tenth stage

Further, after the break, you need to go beyond the installation of the second, and most important layer of flooring. A side panel (side, top or bottom) should be moved a short distance (less than 50 cm and not less than 30) from the rail of the first row of panels. A more detailed features of the process of laying the second layer of a laminate is most often described in the attached instructions.

But it is worth noting that in this case there is a secret. In order to laminate panels easier connected to each other, use a small block of wood and hammer or other heavy object.

eleventh stage

Be sure to follow all of these tips and instructions and you can be sure that your floor will look spectacular and will last for many years. Mainly pay attention to the fact that each successive layer of the laminate is superimposed on the previously stacked layers of two or more substrates. It is also important to note that one and other type of substrates are superimposed on each successive layer overlapping by 7 cm. And the place where they are connected to each other need to carefully smear glue, for greater reliability. Features of the correct folding of the laminate made with his own hands, will be shown in the video, which is located at the end of the article.

the twelfth stage

Each type of laminate flooring has its own characteristics and it is natural that some aspects of laying coating instructions may vary. But it is worth noting that in general, the theory and process in the same self-laying laminate.

Instructions above make it possible to perform all steps of the process. A study in detail the documentation attached to the flooring, you can get more of it advanced information and will know at what point you should pay special material Attention. In addition, the guide will tell you about the features of care.

Important! Never make cutting pieces without first Having measured the exact size. If eventually you will run out of the material, not the fact that the store where you bought it to be the remains of the desired model.

An example of how to lay laminate own hands: video instruction

Perhaps the video version of turn-based instruction laying laminate with their hands will be more informative for meticulous craftsmen

findings

Every person aspires to equip their housing for maximum comfort and style. And the head of the family is trying to do everything yourself. No exception and laying laminate own hands with the help of step by step video and text instructions. Do not be afraid to discover new experiences in this field, for developing, you grow in the eyes of others.