Error 651 occurs when there is no Internet connection
CONTENT
- 1 What does "Error 651" in Windows when connecting to the Internet
- 2 Causes of failure
- 3 What if the reason is the lack of a physical connection
- 4 How to fix the error 651 when incorrect settings, network connection
- 5 Problems with the provider
What does "Error 651" in Windows when connecting to the Internet
When you see this problem on the user's screen displays a system message with the information that the communication device used to connect to the network returned an error code. After the appearance of this information in the monitor, most try to call your ISP to find out the reasons for failure, but more often likely the problem is the lack of physical connection or incorrect configuration of the network connection on the side user. The appearance of the error is the inability of a connection, what the system reports an error 651.
failure is accompanied by the emergence of a system message indicating the approximate cause trouble
Causes of failure
There are few of the most common causes leading to the emergence of such trouble on your computer. Some of them are associated with physical failures, and some may be caused by incorrect settings:
- Damage to the power cable or equipment;
- mismatch network card drivers;
- failure in the normal operation of the PPPoE client;
- and blocking the outgoing or incoming connection firewall Antivirus;
- presence in the user's computer a second network card.
Cable damage can occur not only in the apartment, but also outside it, then it is the fault provider
In rare cases, the lack of high-speed connection can occur through the fault of the provider (the work on the line, a hardware failure, preventive measures).
As practice shows, often the lack of connection arises due to incorrect actions of Users who unknowingly or accidentally made changes to the operating system in the normal operation of the network settings.
What if the reason is the lack of a physical connection
If the source of the problem are not the actions of the provider, the correction of errors do not require the user to more knowledge of the operating system. It is important to observe a sequence of diagnostic steps to identify the cause and then fix the failure.
Reconnect the plug into the socket should be implemented until it locks padlock
Damage to the power cable or connector
One of the most frequent causes of lack of high-speed connection is a LAN cable damage. Despite the apparent protective insulation, it is easy enough to scratch or break. This can happen in the presence of pets, who love to chew wires. Also damage the power cord can be furnished. To eliminate the trouble should be a check on the integrity of the wire. If there is visible damage, replace it with a new one.
Sometimes it fails on a roll connector. Therefore, another method of correction is to reconnect the wires to the appropriate connector on the computer. When connecting should hand a click lock.
If the damage of the router does not make sense to repair it, it is better to buy a new
Failure of a modem or switch
It is likely that the problem was caused by a malfunction of the router. To verify this fact, it is recommended to perform two consecutive steps:
- Disable the device from the outlet for a few minutes. This is necessary in order to reset the current session. After switching back again to try to establish a connection.
- In the absence of such, you must try the direct connection. This means that a network cable coming into the apartment, you need to connect directly to PCs, without going through a router or switch.
TONOTICE! (Click to see)
With a direct connection to enter the login and password issued by the service provider at the conclusion of a contract for services.
If it turns out that a direct connection is made, then we can safely say that the problem is an error in the router, which is need to change.
Even a small "sample" of static electricity may cause damage to the network card
Faults network PC card
Third physical malfunction that can lead to failure, the problem is from the network card. It is likely that there was a small voltage drop due to a temporary failure in the normal operation of this unit. Solve the problem usually will restart your computer.
Also, make sure the network card performance can be visually. Near the connectors for the plug indicator light that lights up in the presence of the network. If the cable is connected it is not lit, it indicates physical damage to the card. In this case, the only way to solve the problem is to purchase a new part and its replacement.
Last minute availability indicators show the connection of the working card status
How to fix the error 651 when incorrect settings, network connection
Identification of physical problems is the fastest method to solve the problem and does not require any knowledge of the internal features of the operating system. Few things are more complicated when the error 651 is a consequence of the OS system failure or incorrect operation. To solve the problem will require a little more time and knowledge.
Not to check which one is not working, it is better to organize a new connection
Check the router settings and protocols
The simplest and quickest way to solve the problem if there is a software failure is to create a new connection. This saves the user from long search malfunctioning protocol and will make sure that the reason is an incorrect configuration of the router, or the router.
Built-in connection wizard gives clear hints to the user's actions
Run a new connection as follows:
- View "Panel Control" menu and go to "Control Center Network and Sharing Center." The user will see all the available connections. You must select the one that is causing the error 651, and remove it by clicking the right mouse button and selecting the appropriate option from the pop-up menu.
- Next, press the keyboard combination Win + R. In the command prompt, type the command rashone.exe.
- These actions are necessary to display the settings of the new connection wizard. The first thing you want to select the "High Speed".
TONOTICE! (Click to see)
To complete the setup, simply follow the wizard. During the creation of the connection need to enter a user name and password issued by the provider at the conclusion of the contract.
The bottom panel all manufacturers specify credentials for the router's menu
A similar process occurs when using a wireless router. To create a new connection and configuration of equipment is required to connect the device to a PC via a patch cord and connect it to the network cable coming into the apartment. Further, through the computer, follow these steps:
- enter the router menu. To do this, the browser will need to dial the corresponding address;
- after accessing the router's settings need to open the tab Internet or Network (depending on the model);
- Next, you need to select the connection type (PPPoE by default), and enter the username and password issued by ISP.
TONOTICE! (Click to see)
Most often, the manufacturer places on the bottom panel of the router label, which shows the details of the entry (IP address, username and password). Usually a bunch of admin / admin is used to access the menu, and for the address 192.168.0.0 or 192.158.0.1
To connect through a wireless router you need to select PPPoE
More dramatic correction methods arising trouble is reset TCP / IP settings and change the type of connection when using the router.
For the commission of the first action the user should take the following steps:
- Start a command prompt with administrator rights (cmd / i).
- Further, the reset command netsh winsock reset.
- To input a new value through the team's nets hint ip reset c: \ resetlog.txt.
- Reboot the computer and verify access to the network.
TCP / IP - the data exchange system used for internet use
When using the router and your computer has the operating system Windows 10 problem with the inability to login to the network can occur with a change in the type of connection. For issuing the correct option will need to log on the router, go to the Internet tab or Network, and select the correct type (PPPoE). Further settings you need to save and reboot the PC.
To change this, you can use the appropriate command
Troubleshoot problems with Antivirus or firewall
Included defenders can block access to Internet applications that are considered suspicious. In this case the correct method of solving the trouble will be the inclusion of the program to the exceptions list.
Firewall - is a program that blocks unwanted network connections
TONOTICE! (Click to see)
Not recommended at all off the security system, as in this case increases the likelihood of contracting a PC virus. To avoid this cause of the problem, it is possible for some time to turn off the firewall or anti-virus and produce a login attempt to the network.
Creating a connection rules will make exceptions for programs or processes that are not objectionable
To create an exception in your firewall, do the following:
- go to "Control Panel";
- go to the tab "System and Security";
- select "Firewall";
- open list "Resolution interact with the application";
- the Exceptions tab, select the program for which the exception will be made;
- the final action will be exhibiting ticks opposite buttons "public" and "private network".
To save the results need to simply click OK and try to go to the Internet. Do not be amiss to pre-reboot.
Similarly, you can create rules for access to the network of trusted processes in the antivirus
Updating drivers
Among the causes of the occurrence of error 651 are properly working network card driver. To update them, the most correct way would be to visit the manufacturer's website site and download the latest version for your device. After completion of the process required to restart your computer for the changes to take effect.
For information about the manufacturer network card can use special tools of diagnosis
Remove the conflict in the presence of the second connection
Connection to a single computer network of two parallel sessions recognized by the system as a conflict. In this case, an error may occur. To eliminate it is not enough just to remove the cable. It should go to the "Control Panel", open the "Network and Sharing Center" and to disable one of the adapters via the context menu of the right mouse button.
Solution to the problem of the parallel network connection is forced off the second adapter
Actions with the registry for the server OS
If the problem occurs when the server version of the operating system, then it can be solved by modifying the system registry. This action is not a simple thing, but for people who understand the computer is not difficult to make the necessary adjustments:
- open the registry editor regedit command;
- find the branch HKEY_LOCAL_MACHINE \ SYSTEM \ CurrentControlSet \ Services \ Tcpip \ Parameters;
- on an empty area of ββthe window right click and select "New", then - parameter DWORD;
- EnableRSS assign a name with a value of 0;
- DisableTaskOffload create additional parameter with the value 1.
TONOTICE! (Click to see)
When the last line is present in the registry, the user just need to change the value in the "unit".
After that, it is necessary once again to restart your computer for the changes to take effect.
Creating a new string parameters in the registry requires a user defined knowledge
Problems with the provider
If you have problems with the provider, the only way will be waiting for the moment when everything will be fixed. The user can get an answer when they call on the phone hotline support. As a rule, if the planned works are carried out, or have been damaged in the pipeline, the company that provides services, trying to fix everything as soon as possible.
Problems with the provider occur infrequently, usually during maintenance activities on the line
Do not be afraid of the error 651. It is not critical and, in compliance with the correct sequence of actions quite easily corrected. More time to see how to solve this problem, it is possible from the submitted videos.